Razor Motorcycles - Recent Questions, Troubleshooting & Support


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Razor, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?q=Fuse+box+location+Razor+Dirt+Rocket+MX500&source=lnms&tbm=isch&sa=X&ved=0ahUKEwiM34n6mJviAhURheAKHSXGD8IQ_AUIDygC&biw=1440&bih=757
https://www.youtube.com/watch?v=saGHHj0CaB0
http://hostmaster.skissle.com/razor_motorcycle_manual.pdf
http://manuals.monsterscooterparts.com/recreational/Razor/manual-razor-mx500-mx650.pdf
https://www.manualslib.com/manual/627248/Razor-Dirt-Rocket-Mx500.html

Razor Dirt... | Answered on May 14, 2019


the batt must read 12.6v always-no less--the alternator probly not workin rite--new brushes may need--stay away from that mechanic and nevr evr replace parts til solution known-relax

Motorcycles | Answered 22 minutes ago


Hi, Mark it should be noted that the reasons your FI light stays on constantly or flashes and your bike will or will not start and may turn over or may not and run great or sputter, these conditions will vary from bike to bike depending on the year, make, and model and you should always refer to your owners/service manual for proper diagnostic procedures. It should also be noted that any type of prior work done to the bike or an abnormal event occurrence IE: adding accessories, electrical curiosity/adventures, laying the bike down/crashes, rain storms/bike washings just before FI light issues started can be significant hints/aids into tracking down the gremlin, also carry the appropriate jumper wire to access fault codes to reduce the risk of being stranded or towed. The newer the bike the more sensitive the ECM becomes and will not let the bike start when aftermarket accessories have been installed without being reprogrammed. That being said the usual suspects are:
1. Faulty Fuel Pump, fuse or system relay switch.
2. Battery starting to fail due to old age/damage, perform a load test.
3. A discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Faulty safety switches/sensors: run/off, ignition, clutch lever, neutral, side stand, tip over, fuel, and or their connections.
5. Broken wire or worn insulation exposing wire to a ground situation especially inside wire harness at tight bends around fairing brackets, under dash panels, under fuel tanks over cylinder heads, etc. Many harnesses are open on the ends that will allow water to enter and accumulate at v-bends.
Dielectric grease and contact cleaner are your best friends for wire/cable/harness connectors, look for corroded, broken, or loose pins/sockets.
6. Installation of aftermarket accessories ie. exhaust systems, mufflers, air cleaners, fuel tuners, electrical component, etc.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://gsx1400owners.org/forum/index.php?topic=1383.0
https://www.gixxer.com/threads/fi-code-flashing.15091/
https://www.manualslib.com/manual/1004329/Suzuki-Gsx1400.html
https://www.partsfish.com/page/oem-parts-for-suzuki
https://www.manualslib.com/manual/905098/Suzuki-Gsx1400.html

Motorcycles | Answered 12 hours ago


Yes, it can be fixed because the company only changes the design, not the capacity and size.

Motorcycles | Answered Yesterday


ASK GOOGLE

Motorcycles | Answered on Jun 02, 2020


Tyre pressure is correct. Jack the front up and check the steering head bearings. Also check steering damper if you have one.

36 psi
The Shop Manual recommends 36 psi front and rear for solo riding, 36 front and 40 rear with passenger.Apr 13, 2014

2003 Heritage Tire pressure - Harley Davidson Forums

Motorcycles | Answered on Jun 01, 2020


Hi, Keith for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Lexmoto, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://125ccbikeclub.awardspace.co.uk/valve_clearance.htm
Lexmoto ZSB 125 Checking and Setting Valve Clearances
Lexmoto ZS125 30 Arizona 2003 2015 Repair Manuals
Lexmoto Arizona 125 ZS125 30 Parts and Accessories Lexmoto Motorcycles and...
Lexmoto Arizona 125 ZS125 30 owners manual and spare parts book eBay

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Motorcycles | Answered on May 29, 2020


NOT FROM FIXYA WE DIDN'T MAKE IT OR SELL IT TO YOU DID WE?

Motorcycles | Answered on May 28, 2020


Try adjusting the air/fuel mixture and raising the rpm

Motorcycles | Answered on May 26, 2020


WELL FIXYA DOESN'T HAVE ONE

Motorcycles | Answered on May 25, 2020

Not finding what you are looking for?
Razor Logo

1 questions posted

Ask a Question

Usually answered in minutes!

Top Razor Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6354 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

richard libby

Level 2 Expert

209 Answers

Are you a Razor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...