20 Most Recent 2005 TN'G Milano 150 Questions & Answers


You should have a solenoid that is the problem. The solenoid is a relay that closes the heavy power to the
starter when the starter switch is closed. The clicking is the solenoid closing but not making contact. The
contacts are burned or dirty. Most solenoids now are not cleanable, just switch out the part.

2005 TN'G Milano... | Answered on Mar 02, 2011


pull up the rubber foot panel and near the back there should be a square panel with 3 or four screws, remove them and take the panel off, battery should be there.

2005 TN'G Milano... | Answered on Jun 13, 2010


thats alot of miles but they run forever. 400 dollars is a good deal so go ahead and buy it

2005 TN'G Milano... | Answered on Nov 06, 2009


The blue header on your posting says a Milano 150cc which is a single cylinder four stroke. You write the bike is 49cc. That small an engine it is probably a two stroke (mix gas with oil)???? Which bike do you have???
Four stroke or two stroke chances are that the carb float has a bit of trash not letting the float needle close fully. Remove the carb and clean it. re-mount it then Remove the water trap bowl from the bottom of the petcock (gas valve). Is there any trash in the bowl?
Dump the bowl and remount. It may be that your bike does not have the water trap bowl I have mentioned.

Use the comments tab to ask other questions.

2005 TN'G Milano... | Answered on Mar 24, 2009


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your TN'G, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?sa=X&q=Open+the+seat+storage+TNG+Milano+150&tbm=isch&source=univ&ved=2ahUKEwie2oviyKLiAhWGylkKHQyFD2EQsAR6BAgIEAE&biw=1366&bih=625
https://www.youtube.com/watch?v=mrfBqjDT5BI
How to Open Your Scooter Seat MegaMotorMadness com
http://www.family-motorsports.net/GY6-50cc-150cc.pdf
https://www.scooterdynasty.com/stockoempartsforscooters-12-2.aspx
https://www.manualslib.com/manual/642297/Tn-G-Milano.html

TN'G Milano 150... | Answered on May 17, 2019


should part of you ing. most times you just turn it the left WITHOUT pushing in
Good luck
M.Woodring

TN'G Milano 150... | Answered on Apr 19, 2011


whats the plug like also whats the mixture on the carb fiddle with this screw until its ok get back to me buddybfa504e.jpg

TN'G Milano 150... | Answered on Sep 23, 2009


According to my service manual, the starter relay is attached to the side of the battery holder, located under the front panel, below the gauge cluster

Motorcycles | Answered 8 hours ago


Hi, Paul for this scenario you will need your service manual that has all fastener torque specs -fluid capacities and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Suzuki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.burgmanusa.com/threads/starting-problems.146778/
https://www.burgmanusa.com/threads/no-start-no-lights-horn-dash.136258/
https://www.manualslib.com/manual/794402/Suzuki-An650.html
https://www.partsfish.com/page/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki/

Motorcycles | Answered 8 hours ago


Hi, Anonymous tail light issues are relatively easy to diagnose and repair always check the tail light fuse first and make sure you have power on both sides of the fuse holder and the usual suspects are:
1. Taillight bulb element is broken.
2. Taillight bulb soldered contacts are extremely worn down.
3. Taillight bulb socket corroded.
4. Taillight bulb socket has no power and or ground.
5. Taillight wiring harness damaged from the rear tire.
6. Taillight rear fender wiring harness connector faulty due to corroded, broken, or loose pins/sockets.
For more information about your issue and valuable "FREE" downloads that you need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.bmwsporttouring.com/topic/93496-2000-r1200c-electrical-issues-114000-miles/
https://www.youtube.com/watch?v=W-MpUdxzhG0
https://www.manualslib.com/manual/368742/Bmw-R-1200-C.html
https://www.ascycles.com/BMW/1998/R1200C/Optional%20Equipment%20and%20Accessories,%20Motorrad.html
https://issuu.com/freemail522/docs/bmw_r1200c_owners_manual_pdf

Motorcycles | Answered 8 hours ago


Hi, John and the usual suspects are:
1. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
2. Failed alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. A failed main circuit breaker or ignition switch, check for loose connections and continuity.
5. Failed system and or ignition relay, check for continuity.
6. Failed ignition coil, stator, magneto, ignition/electronic module.
7. Failed CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Faulty neutral, side stand or clutch lever safety switch.
10. Faulty or corroded kill switch.
11. Accelerator pump damaged or not working.
12. Water or dirt in the fuel system, carburetor or filter.
13. Restricted, blocked or kinked fuel line.
14. Fuel tank empty.
15. The gas cap is not venting properly or fuel tank venting system blocked, loosen the gas cap and go for a test ride.
16. A failed fuel pump, pressure regulator and or fuel injectors.
17. Vacuum line from the intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
18. Needle and seat stuck closed in the float bowl.
19. Petcock clogged or damaged.
20. Lean angle switch is faulty or needs adjustment.
21. Catastrophic engine failure, perform a compression test.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://modernvespa.com/forum/topic91295
https://www.youtube.com/watch?v=v3G4tx3zcCY
https://www.manualslib.com/manual/1105923/Malaguti-Madison-125.html
https://www.scooterdynasty.com/madison1254tlc.aspx
https://absolutelyscooters.net/pdf/CGEN_dawg_scooter_manual.pdf

Motorcycles | Answered 8 hours ago

Not finding what you are looking for?
2005 TN'G Milano 150 Logo

11 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top TN'G Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6422 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Are you a TN'G Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Milano 150 TN'G

  • Milano 150 TN'G

Most Popular Question

scooter sputtered quit while riding gas

  • Motorcycles
Loading...