2008 KTM 250 SX-F - Answered Questions & Fixed issues
2008 KTM 250 SX-F throttle sticks every twist
Yep, lube lube lube.
Take your throttle grip off and lube up your cables.
Check for quick return while it is apart.
Now make sure the grip is not rubbing (common problem), and just move it out till it is free, lube and tighten it back up in this position.
If that doesn't work check for worn out cables?
Good luck.
10/2/2017 1:29:43 PM •
2008 KTM 250...
•
Answered
on Oct 02, 2017
•
230 views
How to tightin my rev cable
Near the throttle body there is two nuts on both cables one is your throttle and the other is your return cable check to see if the return cable is in its cable seat if it is not you will have to reseat it but if both cables are seated correctly you will have to losen both lock nuts on both cables once you have done this twist your throttle to the idel position and hold there tighten both cables and lock nuts and this should fix your problem
5/14/2014 12:40:26 AM •
2008 KTM 250...
•
Answered
on May 14, 2014
•
103 views
What type of clutch oil do I use for my 2006 ktm
Do you mean brake fluid for clutch pump or oil for the engine?If you ask about oil for engine KTM recomend Motorex Power Synt 4T 10W-50.If you ask about the clutch brake fluid you will need brake fluid DOT 4 or DOT 5.1. See link: http://www.manualslib.com/manual/90432/Ktm-250-Sx-F.html?page=36
1/11/2014 12:35:03 AM •
2008 KTM 250...
•
Answered
on Jan 11, 2014
•
580 views
2011 ktm250 sxf wont start
i have a 2009 ktm 450 sxf and was riding yesterday and it stalled out when i switched to fourth gear and wont start back. battery is good and when i hit the e start it just clicks once, and it wont roll start either. any suggestions? could it be the switch under the tank? PLEASE HELP!
12/15/2012 6:23:12 PM •
2008 KTM 250...
•
Answered
on Dec 15, 2012
•
784 views
Ktm 250sxf the clutch does not engage?
hey man bout your clutch not working the master cylinder is prob gone and your hydraulic fluid has all leaked out its an easy fix jus take off cover for your fluid on left hand side of handle bars if the resevoir is empty then you no its master cylinder.
3/22/2012 1:25:23 PM •
2008 KTM 250...
•
Answered
on Mar 22, 2012
•
780 views
How do I install the cam chain back on the cams of
line the TDC mark on the flywheel/crankcasing up , then the cam shaft marks paralell to the cylinder head mating surface then fit chain, fit chain tensioner, take plug out and turn by hand to make sure valves aren't knocking, **** squeeze bang blow! intake fuel, compression, ignition exhaust out
1/27/2012 4:09:27 AM •
2008 KTM 250...
•
Answered
on Jan 27, 2012
•
627 views
I need engine torque settings on my 2008 ktm sxf
Thank you for contacting FixYa with your inquiry. I have been going
over some of the older help requests that have been archieved and
trying to provide solutions for those that didn't get answered. Hope
this information helps.
Try these:
KTM Torque settings
- Collar screw, front wheel spindle Front axle nut 40Nm 30ft lbs
- Brake Caliper front Brake Caliper front Loctite 243 2 19ft lbs
- Brake Disk, front Brake disk front Loctite 243 1 11ft lbs
- Brake Disk, rear Brake disk rear Loctite 243 1 11ft lbs
- Clamping screws, upper fork bridge Top triple clamp 20Nm 15ft lbs
- Clamping screws, lower fork bridge Bottom triple clamp 15Nm 11ft lbs
- Clamping screws, fork stubs Front axle pinch bolts 10Nm 7ft lbs
- Collar nut, rear wheel spindle Rear axle nut 80Nm 59ft lbs
- Hex nut swingarm bolt Swingarm nut 100Nm 74ft lbs
- Hex collar screw handlebar clamp Upper handlebar clamps 20Nm 15ft lbs
- Allen head screw handlebar support Lower handlebar clamps Loctite 243 4 30ft lbs
- Shock absorber top Shock absorber top bolt 60Nm 44ft lbs
- Shock absorber bottom Shock absorber bottom bolt 60Nm 44ft lbs
- Sprocket screws Rear sprocket bolts Loctite 243 3 25ft lbs
- Ball joint for push rod Rear brake pedal pivot Loctite 243 1 7ft lbs
- Engine mounting bolts Engine mounting bolts 45Nm 33ft lbs
- Engine brace Engine brace 33Nm 24ft lbs
- Screw adjusting ring spring preload Shock preload collar bolt 8Nm 6ft lbs
- Spoke nipple Spokes 5Nm 4ft lbs
- Other Screws on chassis M6 10Nm 7ft lbs
- M8 25Nm 19ft lbs
- M10 45Nm 33ft lbs
- Other collar nuts on chassis M6 15Nm 11ft lbs
- M8 30Nm 22ft lbs
- M10 50Nm 37ft lbs
- Front Sprocket 44ft lbs
TF
10/29/2011 7:35:35 PM •
2008 KTM 250...
•
Answered
on Oct 29, 2011
•
524 views
Not finding what you are looking for?