20 Most Recent
2003 kawasaki GPZ 500 S - GPX 500 R Questions & Answers
Overheating
I've never been a big fan of automotive oil in a bike. That being said, maybe the Castrol can be used in bikes too I don't know. Anyhow, hopefully someone will be along that can better answer that part of your question. There have been many discussions pertaining to what oil to use. Drop a PM to OilDoc. He can probably answer that question very quickly for you. If this was a car, I'd say that the thermostat was stuck. Maybe start there.
NINJA 500 MOTORYCLE JUST QUIT RUNNING. IT JUST
put the bike in neutral, find where the positive wire is bolted to the starter, hook a jumper cable to the positive terminal on the battery and with the ignition on, touch the other end to the positive bolt on the starter. if the starter works, then its likely your kill switch is malfunctioning. take it apart if necessary clean or replace... hope this helps.
Change fork seals Kawasaki GPZ 400
If you are not VERY mechanically inclined...and have the special tools required... .please take this to a professional!! it will be less expensive in the long run.!!
It takes some special tools that only dealers have.
I lost my key to
Before you attempt to take out the ignition, call a dealer and ask him if they can get you a key for your bike by using the VIN as reference. Harley and some metrics can do it this way.
No fire to the motor
check coil or wire from coil. could be blown fuse or bad brain...aka CDI in which case you could open it after locating it and possibly discover a bloated capacitor which you can snip off and solder in a new one for 2 bucks. at a radio shack or electronics parts store
Motorbike wont move
sidestand lockout switch is sticking...bike thinks that you're trying to ride away with the stand down so it kills the sparks.
How do u no if ur coil packs are fireing
If you have a wiring diagram, trace out the ignition system this way you trace problems. But you could pull the plugs and put them in the wire and ground it against the head, away from the spark plug hole, turn the engine over and see if it fires, i use a spark tester, but a known good plug will do. If there is no spark then check to see if you have volts at the primary side of coil "the little wires that hook to it test them with the ignition on" if no volts there then begin your volt chace checking all wire and connectors. You will need a multi meter ok. let me know how it goes, just takes patience and time k.
It drives great 1st gear
The cakey, white oil color is water emulsified with the oil. Rainwater, car wash spray, condensation in the tranny, rain water or sprinklers have contaminated the oil. If the tranny will not shift into a higher gear, there is a bent shift fork or two creating the problem. This can be a costly repair and is not recommended for the novice mechanic. Below is a diagram showing how the shift drum rotates to move shift forks left and right to change gears.
Took the carbs off toclean
I would say if you have not messed with the adjutments on your carbs , they are prob ok.
It sounds like if you drain your fuel, tank, all filters, what is left in the carbs
will work it self out, you can remove and drain either way. Go buy new spark plugs and filters
Charge your battery to full charge slow trickle while you working on the other . I am confident that you will be happy with the results .
How can i start a
boost it, it should stay running if the charging system is good, then you can check charging rate
Hi
i got a kawasaki
Kawasaki's are notorious for the waterpump seals going. There are little rubber doughnut seals (3 if i remember) that run along the impellor shaft. When these break down, you get the leak. I would be pretty certain on a bike of this age, that this is your problem. It isnt a massive job to do, but if your not technically minded it can get messy. The shaft is connected by a circlip on the opposite side to pump prop, and should, i emphisise the word SHOULD slide out, once the clip is released. But beware as ALOT of these become siezed and stuck fast, so some more dissasembly may be required. You can try taking off the cover and using a good instant gasket, providing that your running temp is fine, no water in the oil (if your lucky) but these cover seals are designed to pop if there is too much pressure behind them, hence me telling you about the impellor seals.
Hope this helps mate,
Mista B.
Need to clean radiator but
drain the coolant and fill with water and about a half cup of tide powder detergent, run the bike a while and drain, you will have to flush with water several times to remove all detergent before refilling with coolant.
Not finding what you are looking for?