Top 20 2000 kawasaki ZX-6R Ninja Questions & Answers


Go back and check your work. maybe wrong pads too thick something. just look

2000 kawasaki... | 93 views | 0 helpful votes


Hi, Anonymous and the usual suspects are:
1. Idle port, transfer ports, slow air jet clogged.
2. Idle adjusting screw set too low.
3. Air fuel mixture adjustment too lean.
4. Pilot/slow fuel jet clogged.
5. Faulty accelerator pump.
6. Float level too low.
7. Float bowl contaminated old fuel, water, dirt, rust, etc.
8. Carburetor bowl vent line clogged/blocked/pinched.
9. Fuel line to carburetor kinked or pinched.
10. Fuel filter clogged.
11. Intake manifold leak.
12. The gas cap is not venting properly or fuel tank venting system blocked.
13. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
14. Needle and seat stuck closed in the float bowl.
15. Multi carburetors not in sync.
16. Faulty fuel pump or internal fuel line has pinholes.
17. Fuel injectors clogged or faulty.
18. Faulty throttle position sensor.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Ninja starts but dies when open the throttle
http://www.newninja.com/forums/f161/zx-6r-starts-fine-but-dies-when-throttle-is-applied-16041.html
Kawasaki Ninja ZX 6R Service Manual
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2000 kawasaki... | 395 views | 0 helpful votes


carbs might need cleaning also the tank ! how old is the fuel ??

2000 kawasaki... | 125 views | 0 helpful votes


Hi, Mike before testing any electrical component in the Starting Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Engine Run Switch is "FAULTY" or corroded.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
5. Bank angle sensor needs a reset or is faulty.
6. FOB battery low or dead.
7. Faulty ignition switch.
8. Faulty starter button.
9. Faulty kickstand, clutch, neutral safety switch.
10. Security alarm needs a reset.
11. Starter relay, solenoid, starter motor or circuit wiring faulty.
12. Starter armature or field coils have failed.
13. Main fuse or circuit breaker may be blown or faulty.
14. Faulty ignition relay.
15. The electric starter is working but starter clutch has failed.
16. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
98 zx6r won start turn over nothing KawiForums Kawasaki Motorcycle Forums
2003 ZX6R Won Start 1 Engine Won Turn Over
Kawasaki Ninja ZX 6R Service Manual
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


2000 kawasaki... | 161 views | 0 helpful votes


Hi, Frank for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Replace Ignition Lock on 2006 Ninha ZX 6R Sportbikes net
2005 Kawasaki Ninja ZX6R 636 stuck ignition tumbler issue
Kawasaki Ninja ZX 6R Service Manual
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


2000 kawasaki... | 397 views | 0 helpful votes


Most yoshimura exhausts have a large circlip holding in the baffle, some have an 8mm Bolt or alun head bolt, remove the retainer and grip baffle twist an pull slightly to remove some baffles have silicone around them to seal it which could hamper removal

2000 kawasaki... | 400 views | 1 helpful votes


G'day,
I have a suggestion.
It worked with no airbox( airbox lid I guess you mean).
Then I would think that your problem would almost certainly be a blockage or restriction to the air flow entering the airbox intake.
Look in the airbox,with the lid off-And see where the air enters the box- the air ducts on each side.
Make sure these are clear of any obstruction.
Check the air intake vent in the front of the fearing for obstructions.
I feel pritty sure you'll find your problem here(I hope!).
See how you go
Kind regards Andrew Porrelli

2000 kawasaki... | 222 views | 0 helpful votes


Has the bike been setting up over winter or for a length of time over a couple weeks, with gas in the gas in the tank? If so, the ethanol additive to gas has caused the fuel to gum up and block carb jets and passages. My recommendation, if setting up is the case is to put a can of SeaFoam in the fuel tank, shake the bike back and forth to mix the fuel and SeaFoam. Start the bike and run at high idle for a few minutes. Shut it down and let set a couple hours and start and run at high idle again. Repeat this several times trying to accelerate. If it's a gum problem, it should clean itself up with one can of SeaFoam. If it doesn't, it could be an adjustment problem, or the carbs will need a manual cleaning.

2000 kawasaki... | 329 views | 0 helpful votes


Hi, D_daughtr600 for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Removing the Seat from 2009 ZX 6R
2007 Kawasaki Zx6R How to Take Off Your Seat
Kawasaki Ninja ZX 6R Service Manual
OEM Parts for Kawasaki
Kawasaki Ninja ZX 6R Owner Manual

2000 kawasaki... | 292 views | 0 helpful votes


Please replace your spark plug with new one. Just use the recommended spark plug.

2000 kawasaki... | 211 views | 0 helpful votes


Hi, best thing is to get the tyre removed and fitted at a reputable garrage, not sure if you have a brand new wheel, in which case you will need to remove and replace the bearings and seals from the wheel, seals just push in and bearings are a tight fit and often need renewing when removed, fit into new wheel in the same way, using a lite grease when re fitting, most discs are handed left and right, locate the direction of rotation markings which you will find on one of the spokes on the wheel, remove discs 1at a time and replace on to new wheel on the same side as that it was previously fitted on the old wheel, good luck

2000 kawasaki... | 134 views | 1 helpful votes


do not try starting again until oil level and water level are confirmed. I would have a mechanic take a look at it to know for sure but sounds like you may have blown the head gasket

2000 kawasaki... | 152 views | 0 helpful votes


That is a lean condition,on the bottom side of carbs are mixture screws,if they are located on front side of carb between cylinder they are fuel/air turn counter clockwise1/4 turn to richen,if on backside of carb,between air box/filter they are air/fuel,turn clockwise 1/4 turn to richen,then check,if you blip throttle and rpms drop then rise its to rich,may have to try few times to get it right.

2000 kawasaki... | 157 views | 0 helpful votes


Try to unplug the ventilator and give it directly 12V DC. If it alone works, then your problem is your temperature sensor.

2000 kawasaki... | 118 views | 0 helpful votes


It sounds like that hose which runs fron the cap area (inside) the fuel tank to the back bottom is broke, if you take it to a Kawasaki dealer and have your dealer call Kawasaki there is a good chance it will get covered as long as the tank is damaged. Those hoses (metal) that run inside the fuel tak sometimes crack, there is really not way of fixing them unless you cut the tank open and then you would need to reweld it.

2000 kawasaki... | 1,292 views | 1 helpful votes


I haven't worked on a ninja of this year, but most sport bikes this year require you to remove the seat, then tank, then air box, and the spark plugs should be accessable at that point. It's not difficult, but usually takes a couple hours if you're being careful. Make sure your gentle with the fuel lines.

2000 kawasaki... | 137 views | 0 helpful votes


Start with plugs. If this don't do it. You may have some bad parts in your carbs. Think about having them rebuilt not just cleaned.

2000 kawasaki... | 216 views | 0 helpful votes


no fuel will definitely be a problem. make sure all connections are good.

2000 kawasaki... | 250 views | 0 helpful votes


Stop riding the bike. The tranny could lock up at any moment > like at 60 mph in traffic. The gearbox will need to be opened upand the problem located and fixed. The fix is not going to be cheap $$$$

2000 kawasaki... | 136 views | 0 helpful votes


Hi, Dctalavera for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
2000 Kawasaki ZX 6R Ninja wiring diagram Google Search
Kawasaki Motorcycle Wiring Diagrams
Kawasaki Ninja ZX 6R Service Manual
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2000 kawasaki... | 206 views | 0 helpful votes

Not finding what you are looking for?
2000 kawasaki ZX-6R Ninja Logo

43 questions posted

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6339 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

217 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

ZX-6R Ninja kawasaki

  • ZX-6R Ninja kawasaki

Most Popular Question

remove baffle from yoshimura exhaust

  • Motorcycles
Loading...