1996 kawasaki ZXR 400 - Answered Questions & Fixed issues
I have a 2004 Kawasaki
Sounds like a bad starter without knowing what sounds it made when you turned it over etc. if it did absolutely nothing when you tried to start it but started when jumped via solenoid it’s either wiring between the button and starter or wiring between the solenoid and starter itself
Dead wet spark plugs
over fueling , when was carbs cleaned out last and fuel system cleaned ? is choke sticking on slightly
Trouble starting and oil cloudy
try removing your spark plug then turn your engine over a few times but be careful there may be some oil or gas that sputters out so have a rag ready. Do that a few times until you dont see anything coming out then replace spark plug and try starting it again. If that doesnt solve it you may have to replace you rings ( on the pistons)
My silencer is blowing between
Remove the silencer and clean up the down pipe and silencer ends.
Use a liberal amount of exhaust repair paste and push the silencer back on.
Refit the clamp that holds the pipes together and replace any perished rubberised band that may be used.
Run the motor on idle for about 10 mins to harden the paste and the leave overnight.
Recheck the clamp for tightness and hopefully all should be well with the world, the sun will be shining and you can go for a ride.
I replaced plug wires:
hi you dont say what model kawasaki you have im assuming you have a transverse four like a z1000 generally speaking as you sit on the bike the outer cylinders are 1 and 4 the inner cylinders are 2 and 3 ,now again im assuming you have two coils, each coil has two plug leads
coming out of them coil number one will serve cylinders 1 and 4 it doesnt matter which of these leads goes to either 1or 4 as bikes use a wasted spark system and will spark on the exhaust stroke as well, coil number 2 will serve cylinders 2 and 3 again it wont matter which plug lead goes to either 2or3 ok now for the tough part
you need to find the sparking point for no1 cylinder remove no1 spark plug probably the outer left cylinder as your sat on the bike and turn the engine over by putting the bike in gear (only do this with no plug leads connected as it could start unexpectedly in gear ) and push or bump the bike gently with the clutch out to bring the piston to the top of the bore a small torch would be handy for this to shine down the plug hole you then need to find a timing cover on the outside of the engine
you may need a service manual for this as there are many variations but usally there are two pick up modules one for each coil the timing marks correspond to each coil with cylinder 1 at the top of the bore the timing mark should be near number 1 pick up module now that you know which module number one is follow the wiring back to the coil ,each pick up wiring is a different colour like black and orange wires for one coil and black and green for another when you have found number one coil attach plug leads to it and fit them to cylinders 1 and 4 you then fit the remaining coil with plug leads to 2 and 3 cylinders refit the spark plug take the bike out of gear and go for a start good luck with this
Problematic carburetor on 400cc Kawasaki
I'll need some more information. Does the bike start at all? Does it idle fine, but then dies if you give it gas? Try to explain in detail what is going on so I can help you with this. There are a few things to check for, start by making sure your gas is good DON'T USE ANY GAS WITH ETHANOL (corn stuff) and that it is new. Another thing is to make sure you are getting spark. A simple way is to take the spark plug out while keeping it in the wire and touching it to the outside of the engine (grounding it), turn the motor over and you should see spark. If not, thats something you will need to correct. You don't have a year or what type of motorcycle so I'm assuming its a late 70's, early 80's KZ400 you are talking about. If so, the points could be the culprit as well (if the spark isn't going). But for the most part, the "needle" settings will only help with it's ability to rev high (main jet) and if it dies at idle, your idle jet is plugged up. Get back to us on the specifics and I can help more.
Bruno
Here is a great site if it IS a KZ400
http://www.kz400.com/
Wont start turn the key
TO ELMINATE THE STARTER, FOLLOW THE WIRE FROM THE + SIDE OF THE BATTERY TO THE STARTER REAY IE SOLENOIDE, YOU WILL SEE 2 X NUTS HOLDING THE CABLES TO IT, THE SOLENODE IS A MAGNETIC SWITCH WHEN YOU PRESS THE STARTER BUTTON THE SWITCH JOINS TOGETHER THE 2 WIRES, TO TEST THE STARTER MANUALY YOU WILL NEED TO JOIN THESE 2 WIRES TOGETHER,EITHER BY REMOVING 1 WIRE AND JOINING IT TO THE OUTHER. OR BY USEING AN INSULATED PAIR OF PLIERS AND BRIDGING BOTH CONTACTS, BA AWARE THAT SPARKS NEAR TO YOUR BATTERY COULD CAUSE YOU BATTERY TO EXPLODE AND CAUTION SHOULD BE USED WHEN ANY BATTERY WORK IS UNDERTAKEN, SAFETY GLASSES SHOULD BE WORN AND PROTECTIVE GLOVES, ONLY CARY OUT THIS TYPE OF TEST IF YOU ARE CONFIDENT YOU COULD DO IT WITHOUT CAUSING INJURY,
I have a 2002 Kawasaki Mean Streak 1500 I'm customizing it can the rectifier be moved so it's not just hanging there.
Absolutely, the rectifier on your Kawasaki Mean Streak 1500 can be repositioned during a customization project. The rectifier is a crucial part of the motorcycle's electrical system, converting alternating current (AC) from the stator into direct current (DC) to charge the battery and power the bike's electrical components.
While relocating the rectifier, it's important to consider a few key factors:
- Space and Mounting: Assess the available space on the motorcycle to find a suitable location for the rectifier. Ensure that the new position allows for proper mounting and secure attachment without interfering with other components or the bike's functionality.
- Heat Dissipation: The rectifier generates heat during operation, so it's essential to relocate it to an area with adequate airflow for cooling. Mounting it in a well-ventilated area helps prevent overheating issues.
- Wiring and Connections: When moving the rectifier, ensure that the wiring can be appropriately rerouted to reach its new location. Take care to maintain proper electrical connections and ensure a secure, stable wiring setup.
- Protection: Consider adding protective measures, such as shields or guards, to safeguard the relocated rectifier from road debris, water, or other potential hazards.
Modifying the placement of the rectifier may require custom brackets, mounts, or fabrication work to secure it in the desired location. It's crucial to execute the relocation carefully, maintaining proper electrical connections and ensuring the rectifier's safety and functionality.
If you're not confident in performing these modifications yourself, consulting a professional motorcycle mechanic or technician with experience in customizations can be highly beneficial. They can offer guidance, expertise, and ensure that the modifications are carried out safely and effectively.
12/23/2023 9:33:25 PM •
kawasaki...
•
Answered
on Dec 23, 2023
•
695 views
Not finding what you are looking for?