20 Most Recent 2005 Honda VTX 1300 R Questions & Answers


Hi, Tom before testing any electrical component in the Starter Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries. Depending on battery voltage starter relays and starter solenoids can make the same noise when you hit the starter button. You can easily determine which one is at fault by two simple tests:
STARTER RELAY- place your thumb and index finger on the starter relay and press the starter button, if you feel the click then the relay is faulty and needs to be replaced.
STARTER SOLENOID- bridge the positive and negative poles of the solenoid with a small screwdriver if you get a loud clunk then the solenoid needs to be rebuilt or replaced as necessary. If the engine turns over then replace the starter relay.
A motorcycle starter relay is an electronic mechanical switch that has a small coil winding around a piece of metal that requires low amperage and thin wires to be activated. When you turn on your ignition switch power 12 volts is sent to the relay coil which in turn becomes a magnetic contact point that pulls a spring-loaded contact point to itself completing an electrical circuit that allows more amperage necessary to be accessed by the starter solenoid which in turn acts in the same way as the relay but on a larger scale with its stronger heavier contacts making available the necessary amperage to turn the starter motor. If your battery has low voltage it, in turn, makes the magnetic contact point weak in trying to pull its counterpart to make a connection. These relays are usually encased in a plastic housing that is sealed, depending on the quality of the product. When activated they will produce a small amount of heat to their metal components which in turn can create the perfect environment for condensation to form depending on weather conditions and how careless you may be with a water hose or sprayer while washing your bike. After a period of time, several months to several years depending on the circumstances this condensation is the starter button for electrolysis and the slow build-up of corrosion which ends by preventing the magnetic contacts in making a solid connection and alerts you to this situation with the customary greeting "CLICK or BUZZ" if you get a single loud "CLUNK" then the starter solenoid is at fault and needs to be rebuilt or replaced as necessary. The relay is inexpensive and needs to be replaced however in a pinch they can be forcibly opened cleaned and resealed with silicone. In a nutshell, motorcycle starter relays take in low amperage and send out higher amperage when activated and for curious minds, the voltage remains constant at whatever your battery reads at the time.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.vtxcafe.com/threads/2005-1300r-vtx-will-just-click-after-with-new-battery.85443/
https://www.youtube.com/watch?v=MlY-0L50x2c
https://www.manualslib.com/manual/722750/Honda-Vtx1300s.html#product-VTX1300R
https://www.partsfish.com/page/oem-parts-for-honda
http://owners.honda.com/assets/ownerlink/model/own_man/powersports/2004/2004_vtx1300c.pdf

2005 Honda VTX... | Answered on Jul 23, 2020


Hi, Remi for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.vtxcafe.com/threads/replacing-speed-sensor-any-tips-or-tricks.183441/
https://www.google.com/search?q=Speedometer+relay+location+2005+Honda+VTX+1300+R&source=lnms&tbm=isch&sa=X&ved=0ahUKEwim1s7Bu-jkAhUBHqwKHYGmAlIQ_AUIEygC&biw=1440&bih=757
https://www.manualslib.com/manual/722750/Honda-Vtx1300s.html#product-VTX1300R
https://www.partsfish.com/page/oem-parts-for-honda
https://www.vtxcafe.com/threads/2005-vtx-1300r-owners-manual.57763/

2005 Honda VTX... | Answered on Sep 24, 2019


Hi, Mike and the usual suspects are:
1. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
2. Failed alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. A failed main circuit breaker or ignition switch, check for loose connections and continuity.
5. Failed system and or ignition relay, check for continuity.
6. Failed ignition coil, stator, magneto, ignition/electronic module.
7. Failed CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Faulty neutral, side stand or clutch lever safety switch.
10. Faulty or corroded kill switch.
11. Accelerator pump damaged or not working.
12. Water or dirt in the fuel system, carburetor or filter.
13. Restricted, blocked or kinked fuel line.
14. Fuel tank empty.
15. The gas cap is not venting properly or fuel tank venting system blocked, loosen the gas cap and go for a test ride.
16. A failed fuel pump, pressure regulator and or fuel injectors.
17. Vacuum line from the intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
18. Needle and seat stuck closed in the float bowl.
19. Petcock clogged or damaged.
20. Lean angle switch is faulty or needs adjustment.
21. Catastrophic engine failure, perform a compression test.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.vtxcafe.com/threads/motor-dies-while-driving-sometimes-wont-start.213186/
https://www.vtxoa.com/forums/7-vtx-1300-riders-board/200094-bike-died-while-riding-any-ideas.html
https://www.manualslib.com/manual/722750/Honda-Vtx1300s.html
https://www.partsfish.com/page/oem-parts-for-honda
https://www.manualslib.com/manual/785609/Honda-Vtx1300c-Vtx-2004.html

2005 Honda VTX... | Answered on Sep 23, 2019


Hi, Anonymous I would love to help you with your engine or chassis noise but I just loaned my brand new pair of listening ears to your local dealer's chief technician so he could take your bike for a test ride and give you his professional opinion and estimate about your noise and repair cost. If you are a little short on "DRACHMA" and a Dealership is not on your list of fun places to visit then perhaps the list below will help soothe your worried mind so you can make an informed decision.
1. Bearings---SCREECH---WHINE
2. Belts---CHIRP
3. Brake Rotors---BUZZ
4. Cam Chains---CLICKIT
5. Clutches---CHATTER
6. Cylinders---PING
7. Fairing Panels---WHISTLE
8. Fenders---SCRAPE
9. Fronk Forks---Plunk
10. Fuel pumps---WHIRR
11. Gears---WHINE
12. Head Gasket---HISS
13. Hydraulic Lifters---TAP
14. Instrument Clusters---BUZZING
15. Kick Starter---GRINDS
16. Pistons---SLAP
17. Power Valves---CLINK& RATTLE
18. Radiators---GURGLE
19. Rear Chains---RATTLE
20. Rear Shocks---SQUEAK
21. Relays---CLICK&BUZZ
22. Shaft Drives---WHIRR
23. Shifting Trans---CLUNK
24. Solid Lifters---TICK
25. Speedometers---bzzz
26. Starters---CLICK
27. Rods Go---KNOCK-KNOCK---who's there, it's me "*****"
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.vtxcafe.com/threads/loud-rear-end-noise.18377/
https://www.vtxoa.com/forums/7-vtx-1300-riders-board/271334-rattling-rubbing-grinding-noise-driving-me-crazy.html
https://www.manualslib.com/manual/722750/Honda-Vtx1300s.html
https://www.partsfish.com/page/oem-parts-for-honda
https://www.manualslib.com/manual/1123139/Honda-2007-Vtx1300s.html

2005 Honda VTX... | Answered on Sep 23, 2019


Hi, Cristilike19 and the usual suspects are:
1. Contaminated or faulty speed sensor.
2. Faulty turn signal module.
2. Corroded, broken or loose connector pins/sockets in the wire harness between the speedometer and the ECM or TSSM and the sensor.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Speedometer Not Working
Help speedo not working
Honda VTX1300S Service Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda VTX1300C VTX 2004 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2005 Honda VTX... | Answered on Feb 19, 2018


Hi, Shirleypaw and the usual suspects are:
1. Fuel cap or fuel tank is not venting properly.
2. Fuel filter clogged.
3. Fuel line pinched or kinked.
4. Vacuum line from the petcock to intake manifold cracked.
5. Float needle and seat sticking.
6. Float level too low.
7. Carburetor bowl vent line clogged/blocked/pinched.
8. Idle adjusting screw set too low.
9. Air/fuel mixture screw set too lean.
10. Idle port, transfer ports, slow air jet clogged.
11. Slow fuel jet clogged.
12. Faulty fuel pump.
13. Faulty auto choke or wiring connection.
For more information about your issue and valuable "Free" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
07 VTX 1300S won idle after adjusting screw to 2 1 2 turns out 2005 VTX1300 won stay running
Honda VTX1300S Service Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda VTX1300C VTX 2004 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2005 Honda VTX... | Answered on Feb 18, 2018


Hi, Vijay_gautam the answer to this question is way above my pay grade for this situation, I would call or visit my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts inquiry.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Honda VTX1300S Service Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda VTX1300C VTX 2004 Owner Manual
Honda VTX 1300 2005
Honda VTX Series

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2005 Honda VTX... | Answered on Feb 18, 2018


Hi, Michaeldanny for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Clutch Adjustment
How to adjust motorcycle clutch cable
Honda VTX1300S Service Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda 2007 VTX1300S Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


2005 Honda VTX... | Answered on Feb 18, 2018


Yes you did, floats are not closing needle valves.

2005 Honda VTX... | Answered on Feb 18, 2018


Hi, Monte348 and the usual suspects are:
1. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a cursory reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
2. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Spark plugs in bad condition or partially fouled.
4. Spark plug cables in bad condition and leaking check for spark leakage in the dark
5. Spark plug gap too close or too wide.
6. Faulty ignition coil, module, and or sensor.
7. Loose, dirty, or corroded ignition module connector at crankcase.
8. Faulty CKP or CMP, MAP, ETS, ATS, TPS, O2 sensor.
9. Dirty air filter.
10. Intake air leak.
11. Water, dirt, or rust in the fuel system.
12. Carburetor contaminated, sticky float, plugged jets.
13. Carburetor has oil in the bowl due to excessive oil in pre-mix.
14. Carburetor vacuum diaphragm torn, cracked, not seated or installed improperly.
15. Multiple carburetors out of sync.
16. Fuel filter clogged.
17. Old or contaminated fuel.
18. Fuel tank vent system plugged or carb vent line closed off.
19. Gas cap diaphragm valve faulty.
20. Vacuum line from intake manifold to fuel valve is broken, cracked, pinched, or missing.
21. Carburetor controls misadjusted.
22. Incorrect valve timing.
23. Valve springs floating, weak, or broken.
24. Damaged intake or exhaust valve.
25. Incompatible performance parts.
26. Control module may be in "LIMP" mode
27. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
engine misfire very intermittent
Misfire question
Honda VTX1300S Service Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda VTX1300C VTX 2004 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2005 Honda VTX... | Answered on Feb 10, 2018


Hi, Donalddangle for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Driveshaft fluid change
Final Drive Service VTX NSR Tech wmv
Honda VTX1300S Service Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda VTX1300C VTX 2004 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


2005 Honda VTX... | Answered on Feb 04, 2018


Hi, Chris_I_hard if you have changed your engine size, fuel delivery system, air filter size or flow rate, mufflers or exhaust system or a significant change in altitude your carburetors need re-tuning and if your fuel system (gas tank, filters, fuel valve, and carburetor) is contaminated with ethanol sludge, varnish, rust, dirt, water etc. or your bike has been sitting for months or years without running these components must be "PROPERLY" cleaned and reassembled "CORRECTLY" before any adjustments can be made. Tuning your carburetor is fairly simple once you understand the basic principals. You engine is a simple airbox sucking air in and blowing it out, it is finely tuned at the factory for maximum performance once you upset that delicate balance by changing air filters, camshafts or exhaust systems your performance may go down the and the engine may run poorly, you need to compensate the air-fuel mixture in the carburetor in order for the engine to run smoothly and at peak performance. If you are running multi carburetors you need to sync them first and make sure your air cleaner element is clean and dry for paper elements or lightly oiled for foam and meshed elements and properly installed. Here is how and where you compensate trouble: "TIP" if your engine "BOGS" you're not getting enough fuel.
1. Close to 1/8 throttle is managed by the air screw and pilot/slow jet.
2. 1/8 to 1/4 throttle is managed by the air-screw, pilot/slow jet, and throttle slide.
3. 1/4 to 1/2 throttle is managed by the throttle slide and jet needle.
4. 1/2 to 3/4 throttle is managed by the jet needle, needle jet, main jet, and air jet.
5. 3/4 to wide open throttle is managed by the main jet and air jet.
6. A wide open throttle is managed by the main jet.
If you are running lean, spark plug electrode color is white, engine runs hot and feels like it is starving for fuel you need to go up on the jet size or move the c-clip down one notch. If you are running rich, spark plug color is black or dark gray, the engine runs cool, and bogs down when accelerating you need to go down on jet size or move the c-clip up one notch. When your carburetor is properly tuned for maximum performance your spark plug electrode will be a light tan color like coffee with cream. If you prefer fuel economy over performance you can go down on main jet sizes until a satisfactory level of lower performance is acceptable versus MPH, your spark plug color will be whiter and your engine will run warmer. These tuning adjustments will only make improvements if your intake and exhaust system have no air leaks or sealing issues and the entire electrical system is in proper working order and you have no mechanical issues.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Rejetting Instructions
Carburator Theory and Tuning
Honda VTX1300S Service Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda VTX1300C VTX 2004 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2005 Honda VTX... | Answered on Feb 03, 2018


Hi, Gary and the usual suspects are:
1. Throttle cables misaligned or misrouted.
2. Damaged or restricted fuel tank venting system.
3. Intake system air leak.
4. Vacuum piston malfunction.
5. Pinholes or torn diaphragm.
6. Accelerator pump leaking or no output.
7. Plugged bowl vent or overflow.
8. Fuel level in bowl too low.
9. Restricted fuel supply passages.
10. Plugged jets or passages.
11. Worn or damaged needle or needle jet.
12. The choke valve not seated or leaking.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://www.vtxcafe.com/archive/index.php/t-107778.html
no acceleration on throttle 1 2 and more
Honda VTX1300S Service Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda VTX1300C VTX 2004 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2005 Honda VTX... | Answered on Jan 21, 2018


Hi, Papawolf295 for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
2005 HONDA VTX 1300 HORN RELAY LOCATION Google Search
Fixing Motorcycle Horn Circuit
Honda VTX1300S Service Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda VTX1300C VTX 2004 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


2005 Honda VTX... | Answered on Jan 13, 2018


Hi, Mac for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Trip meter reset
http://www.vtxcafe.com/archive/index.php/t-14165.html
Honda VTX1300S Service Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda VTX1300C VTX 2004 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2005 Honda VTX... | Answered on Jan 01, 2018


Hi, Ellisbob43 for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Clutch Adjustment
Clutch Adjustment Help Needed
Honda VTX1300S Service Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda VTX1300C VTX 2004 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2005 Honda VTX... | Answered on Dec 12, 2017


Hi, Ozzdog and the usual suspects are:
1. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
2. Failed alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. Failed main circuit breaker or ignition switch, check for loose connections and continuity.
5. Failed system and or ignition relay, check for continuity.
6. Failed ignition coil, stator, magneto, ignition/electronic module.
7. Failed CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Faulty neutral, side stand or clutch lever safety switch.
10. Faulty or corroded kill switch.
11. Accelerator pump damaged or not working.
12. Water or dirt in the fuel system, carburetor or filter.
13. Restricted, blocked or kinked fuel line.
14. Fuel tank empty.
15. The gas cap is not venting properly or fuel tank venting system blocked, loosen gas cap and go for a test ride.
16. A failed fuel pump, pressure regulator and or fuel injectors.
17. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
18. Needle and seat stuck closed in the float bowl.
19. Petcock clogged or damaged.
20. Lean angle switch is faulty or needs adjustment.
21. Catastrophic engine failure, perform a compression test.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Bike died while riding Any ideas
04 VLX VT600CD Engine shutdown while riding
Honda VTX1300S Service Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda VTX1300C VTX 2004 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2005 Honda VTX... | Answered on Dec 06, 2017


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Remove Install of kickstand switch instructions
http://www.fireblades.org/forums/honda-fireblade/34804-kickstand-removal-kill-switch.html
Honda VTX1300S Service Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda VTX1300C VTX 2004 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2005 Honda VTX... | Answered on Dec 05, 2017


Hi, Azucar1974 before testing any electrical component in the Starting Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
4. Bank angle sensor needs a reset or is faulty.
5. FOB battery low or dead.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand, clutch, neutral safety switch.
9. Security alarm needs a reset.
10. Starter relay, solenoid, starter motor or circuit wiring faulty.
11. Starter armature or field coils have failed.
12. Main fuse or circuit breaker may be blown or faulty.
13. Faulty ignition relay.
14. The electric starter is working but starter clutch has failed.
15. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
vtx 1300 won turn over
Troubleshooting Motorcycle that Wont Start Honda VTX 1800 Partzilla com
Honda VTX1300S Service Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda VTX1300C VTX 2004 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


2005 Honda VTX... | Answered on Nov 08, 2017


Hi, Anonymous you need to make sure you have no intake leaks by spraying some Brake Kleen, Contact Cleaner, Starting Fluid etc. around the intake manifold and seals, if the RPM's go up or down significantly then you have a leak that needs to be fixed before you can continue with the carburetor adjustment.
The engine should be at operating temperature with the choke off to set the idle between 950-1050 rpm. Turn the idle skrew clockwise to increase the idle speed and counterclockwise to decrease the idle speed. If you have access to your air-fuel mixture skrew you may turn it as well, if not there is a video below on how to gain access, make sure you start with clean or new spark plugs. Gently turn the air-fuel mixture skrew clockwise until it starts to bottom out "STOP" do not over tighten as it will damage the taper on the end, now back the skrew out 1-1/2 full turns to establish a starting point start the engine and check the idle rpm's and turn the idle skrew accordingly for 950-1050 rpm if necessary, turn the air-fuel mixture skrew 1/4 turn at a time and let the engine settle for about 10 seconds, turn the skrew clockwise for a leaner mixture and counterclockwise for a richer mixture, you are seeking the highest rpm your air-fuel mixture skrew can acquire without going past 3 full turns from bottom then resetting the idle skrew back down to 950-1050 rpm If you can not detect any rpm change and can not stall the engine by turning the air-fuel mixture skrew all the way in then your pilot/low-speed jet is too big and needs to be replaced with the next size smaller. Final adjustment should be made with a clean air filter mounted to the carburetor.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
idle adjustment
vtx 1300 idle adjustment
Rich Lean Adjust VTX 1300R
Honda VTX1300S Service Manual
https://www.partsfish.com/page/oem-parts-for-honda
Honda VTX1300C VTX 2004 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


2005 Honda VTX... | Answered on Nov 01, 2017

Not finding what you are looking for?
2005 Honda VTX 1300 R Logo

216 questions posted

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6480 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

217 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

VTX 1300 R Honda

  • VTX 1300 R Honda

Most Popular Question

location speedometer relay switch 2005

  • Motorcycles
Loading...