20 Most Recent
1997 Honda XR 600 R Questions & Answers
Overflowing fuel from carb needlejet and holder ok
The fuel control valve on the fuel tank must be defective on the gas tank, it is designed to shut off when the engine vacuum signal is not present, I susspect yours is stcuk on, this causes the carb to overfill and run out the tube.
I have a newly acquired 96 Honda XR600 that will
try making the idol higher.
also if the bike will move with choke open/half way ride it and slowly close the choke as your moving.
this isnt something to worry about to much just that you will burn more fuel because of this. it is something to you will want to fix but it will not ruin the bike
good luck
Hi re: Honda xr600r
Check the wiring from the fuse box to the light itself it can be that the wire is loose
The taillight and headlights blow
The charging system is over charging or you are putting the wrong replacement bulb in. My first thought is that the rectifier has burned out or somehow other malfunction. You will also need to check the battery as a malfunction in the rectifier will over charge the battery and actually boil the liquid (acid) out of it.
Want to know what the
Carburetor jet is not adjustable. It has a precise hole size. For richer mixture, replace jet with larger hole.
Dear expert, I just bought
Hi,
Carburettors are notoriously difficult things to balance without the correct tools. I could not advise that you attempt to try this yourself as there are too many possible variations on the fuel mix and manifold vacuum pressure in the carbs.
The only way to balance carbs properly is to use a mercury manometer. The manometer measures intake manifold vacuume pressure and this tool is specifically designed to set the carbs properly. This will have a major effect on the overall performance of your bike.
Take your xr600 to a proper tuning shop and for a small fee they will set the carbs up properly for you. You will notice a major improvement in the bike and you will definitely not regret it!
Please remember to rate my answer through our rating system. Many thanks for using FixYa.
Honda 500 TRX fa6 has PS on the dash….what does it mean ?
The Power Steering has failed. There has been a factory recall for a suddenly failing electrical steering shaft, that could cause the rider to loose control. This does not have to be your problem but anyhow either the electronics or the pump failed. Error codes or messages usually have to be erased by a simple reset procedure or disconnecting a plug, after repairs are done.
3/31/2024 4:25:47 AM •
Honda...
•
Answered
on Mar 31, 2024
Hiss works but
On the bottom of your speedometer on the left side there is 2 buttons
press the far left one for a couple of seconds and the light should go on
1/8/2024 6:42:24 AM •
Honda...
•
Answered
on Jan 08, 2024
What to torque the head on my 99 CBR 929 Honda in
For a 1999 Honda CBR929RR, the cylinder head bolt torque specifications are essential to ensure proper engine assembly and function. When tightening the cylinder head bolts, it's crucial to follow the manufacturer's recommended torque settings to prevent damage to the engine components.
For the CBR929RR, the cylinder head bolt torque specifications are typically as follows:
1. **Initial Torque:** 29 Nm (2.9 kgf-m, 22 ft-lbs)
2. **Final Torque:** 64 Nm (6.4 kgf-m, 47 ft-lbs)
It's essential to tighten the cylinder head bolts in the specified sequence and in multiple stages, gradually increasing the torque until reaching the final specified torque. The exact tightening sequence can usually be found in the service manual specific to your motorcycle model.
When torquing the head bolts, ensure you're using a reliable torque wrench calibrated in the appropriate units (Nm or ft-lbs). Always follow the tightening sequence precisely to ensure even pressure distribution across the cylinder head gasket.
Additionally, it's advisable to use new cylinder head bolts if the old ones have been previously tightened or stretched beyond their yield point. This helps maintain proper clamping force and ensures the integrity of the engine assembly.
As always, referring to the service manual or consulting a professional mechanic experienced with motorcycle engine assembly can provide additional guidance and ensure the correct torque settings are applied during the cylinder head installation process.
12/10/2023 4:27:33 AM •
Honda...
•
Answered
on Dec 10, 2023
2006 Honda Shadow Arrow 750 VT missing on the rear cylinder fire
. One possibility is that the spark plug or plug wire is faulty 1. Another possibility is that the carburetor needs cleaning and adjustment It could also be due to a valve adjustment issue or a bent rod.
I would recommend taking your motorcycle to a professional mechanic who can diagnose and fix the issue. If you prefer to troubleshoot it yourself, you can start by checking the spark plug and plug wire for any damage or wear and cleaning the carburetor. However, please note that working on a motorcycle engine can be dangerous and requires specialized knowledge and tools. Please take all necessary safety precautions and follow the manufacturer's instructions when working on your motorcycle.
10/22/2023 2:01:22 PM •
Honda...
•
Answered
on Oct 22, 2023
Not finding what you are looking for?