2004 BMW K 1200 GT - Answered Questions & Fixed issues

0helpful
1answer

Bmw 2004 k1200gt started then bogged out while idling. Now it won't start. Just keeps turning over

Most likely the fuel pump regulator.
10/27/2015 5:13:47 AM • 2004 BMW K 1200... • Answered on Oct 27, 2015 • 133 views
0helpful
1answer

Leaking abs modular

Very common problem, if you havent replaced the unit already it can be rebuilt. My company rebuilds these (i work on these specific controllers) and we will be more then happy to rebuild your original unit, no reprogramming required. Basically you need a new controller or yours rebuilt. Hope this helps, Best Regards, Tim 423 327 4108
6/6/2014 9:26:42 PM • 2004 BMW K 1200... • Answered on Jun 06, 2014 • 115 views
0helpful
1answer

Hi My bmw K 1200 Gt cruse control does not work.

Your local BMW dealer can help you with that
9/14/2013 3:38:12 AM • 2004 BMW K 1200... • Answered on Sep 14, 2013 • 120 views
0helpful
1answer

2003 K1200GT WOBBLE AT ABOUT 130KM/PH IN NOT SURE

Bad tie rod ends
2/3/2011 11:43:57 PM • 2004 BMW K 1200... • Answered on Feb 03, 2011 • 164 views
0helpful
1answer

Need to know the abs

Front .1-1.7mm and Rear .2-1.5mm Anything within this range is OK.

However, most of the newer bikes have no provision to adjust the sensor gap.

Good Luck!
9/12/2010 2:02:43 PM • 2004 BMW K 1200... • Answered on Sep 12, 2010 • 209 views
0helpful
1answer

I need 4 exhaust cone bolts, what size are they

there in the uk but will post over sea's go to,,,,,
www.motorworks.co.uk they stock every thing for bmw's
6/26/2010 11:01:33 PM • 2004 BMW K 1200... • Answered on Jun 26, 2010 • 86 views
0helpful
1answer

WANT TO WIRE POWER SUPPLY FOR GARMIN SO ITS LIVE

Bmw accessory plugs can be fitted any where on the bike , i have 3 one for vest, one for passenger vest , one for the garmin
4/22/2010 12:31:01 AM • 2004 BMW K 1200... • Answered on Apr 22, 2010 • 215 views
0helpful
1answer

Bmw k1200 gt

nice bike
1/30/2015 8:16:01 PM • BMW K 1200 GT... • Answered on Jan 30, 2015 • 102 views
0helpful
1answer

How does the bmw 2004 k 1200 gt cruse control work

To set the cruise control it is a two step process if it's not on yet. Step one is to turn it on by flicking the (usually) grey cruise button inward (towards the center of the handle bar, step two is to set the cruise control, this step has to be performed while riding above 25MPH, and it's to flick the now fully exposed tab either forward or backword. This should set the cruise control and the indicator on the dash should confirm it.
5/20/2014 4:59:03 PM • BMW K 1200 GT... • Answered on May 20, 2014 • 128 views
0helpful
1answer

K1200gt head apparently needs shimms at huge cost accourding to the mechanic it has low compression but it runs beautiful,, no oil loss or tappet noise either, this was at the 100000 Kilometer service

Well, the shim adjustment must be done, the question is are you too late? I presume that you are talking about valve shims, which is how the valves are adjusted. Valves work their way into the head, over time, and this closes the clearance, when you hold the valve slightly open, the valve and seat get damaged.This is the time to fix the low compression cylinder, as it will only deteriorate more from this point. Likely a valve issue...And it appears that is what your mechanic is indication. NO MORE adjustment means that the valve has worked its way into the head too far. Valve job time. Sorry.
1/22/2012 1:39:02 AM • BMW K 1200 GT... • Answered on Jan 22, 2012 • 168 views
0helpful
1answer

Noise from right side of

Hello and welcome to FixYa!

I suspect that it's the timing chain tensioner as well. It really makes noise when worn out. I strongly suggest that during the tensioner replacement, have the timing chain be replaced too. This will prevent future engine breakage.

Hope this helps and thank you for using FixYa! Have a good one!
5/24/2011 11:49:18 PM • BMW K 1200 GT... • Answered on May 24, 2011 • 345 views
0helpful
1answer

I have a 2004 K1200GT

Yes, there is a 12 V accy. socket on your bike which can be used to charge the battery while it is still in the bike or for powering 12 V gadgets. If memory serves the socket is located on the LHS of the bike.

GPS consume very little power, so you could wire it directly to the battery with a small (3-5A) fuse in the line. Battery is located directly under the seat.
8/19/2010 12:57:36 AM • BMW K 1200 GT... • Answered on Aug 19, 2010 • 229 views
0helpful
1answer

Mine is BMW 259rt, everything was working well I just washed the bike my Delft carefully but bike cannot start after washing.

you have wet the ignition system , carefully use a hair dryer to dry it out and spray with WD40.
8/18/2021 3:22:38 AM • BMW Motorcycles • Answered on Aug 18, 2021 • 25 views
0helpful
1answer

K 1200. Where is the fuse box?

ever look under the seat
5/8/2021 5:06:19 PM • BMW Motorcycles • Answered on May 08, 2021 • 35 views
0helpful
1answer

2017 BMW HP4 Race owners manual

BMW Owners Manual PDF ,ALL MODEL- get your manual now! https://www.repair-guidebook.com/bmw-owners-manual-pdf-free-download-pdf/
11/7/2020 3:12:05 AM • BMW Motorcycles • Answered on Nov 07, 2020 • 186 views
0helpful
1answer

2004 BMW R1150RS 7,700 Sat for 2 yr with some starting. No spark, bought coils and new plugs. Bike has never been in rain or outside.New battery. turns ovr nice. Please respond if you know this bike

I don't know the bike but I doubt it is much different in principle than many others. The first possibility to consider is whether any immobiliser is functioning properly and is being properly disarmed before attempting to start. The owner's handbook would be a good place to begin... Once you know the immobiliser is disarmed and power is flowing to the parts it is supposed to flow to, using the circuit diagram, the various supplies and grounds can be checked and using an oscilloscope check the output from the various sensors as applicable (crankshaft, camshaft). Even though the bike has never been outside it might not have been immune from the effects of damp and condensation that can defeat many moisture barriers. It isn't unusual for electronic unit and sensor terminals to become dull, oxide coated and a barrier to current flow...
3/6/2020 6:06:44 AM • BMW Motorcycles • Answered on Mar 06, 2020 • 87 views
0helpful
1answer
0helpful
1answer

Driving lights wiring diagram 2006 BMW R1200GS

Easiest way would be to install a switch between the lights and the high beam switch. That way it would still come on only when high beams are on but you could turn them off. Alternately you could rewire them completely so they run only off of a switch, but then you would have to tun them on and off manually all the time. ---> expect to be pulled over for not dimming your lights when you encounter an oncoming police car and you forget they are on.
2/10/2020 3:10:44 AM • BMW Motorcycles • Answered on Feb 10, 2020 • 461 views
Not finding what you are looking for?
2004 BMW K 1200 GT Logo

7 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top BMW Experts

Arnie Burke
Arnie Burke

Level 3 Expert

7095 Answers

mark woodring
mark woodring

Level 3 Expert

498 Answers

woodzowl307

Level 3 Expert

668 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...