already replaced gasket,seals-inner primary,5th gear,new bearing.
Most inner primary leaks come from the alternator o-ring the best thing to do is put on a new one and put clear silicone on the primary and the engine case.
Posted on Mar 03, 2010
my 1998 Dyna has a small leak or drip coming from a small nipple that sticks down from the petcock. Is it time for a enw petcock or will some other trick stop the drip?
Sounds like you have a hole in the vacuum diaphragm that opens and closes the petcock. This is one of the problems with the vacuum operated device. The other problem is that sometimes they don't open and you're left stranded with a full tank of gas and not a drop in the carburetor. I changed to a manual operated petcock. Personally, I'd rather have a Pingle petcock than another vacuum operated Harley petcock. If you do change to a manual operated petcock, don't forget to plug the small vacuum hose.
If you want to keep your vacuum operated device, I think you can buy a replacement diaphragm. You will have to drain the tank and remove the petcock. There are four small screws on the backside. Remove the screws and the backplate will come off. The diaphragm and a sping is all that is in that section of the petcock.
Posted on Apr 01, 2010
step by step proceedure to remove rear fender from 2000 fxdwg
1. Follow the taillight and rear turn signal wire harness to the 8-pin connector under the seat. Separate the connector. Remove the seven wires and the attached socket terminals from the connector.
2. Cut the cable strap from around the harness in front of grommet in the fender. Pull harness thru grommet in fender.
3. Remove (from underside front of fender) screw and washer from speednut on frame.
4. Remove turn signal lamps.
5. Remove screws and washers from rear of fender supports.
6. Remove license plate bracket.
7. Remove screws and washers from front of fender supports.
Posted on Jan 21, 2011
How to remove and replace a starter on a FXWG wide glide 1980 Shovelhead harley
To remove the starter from your Shovelhead, first disconnect the battery and take it out of the battery tray. Remove the battery tray, two bolts that bolt to the oil tank and the rubber mounts. Take the battery cable off the starter motor and take the bracket that supports the rear of the starter motor off. The bracket is bolted to the transmission and the rear of the starter motor. Take the remaining long bolt out of the starter. Work the starer out of the starter drive housing. Do not allow the starter motor to come apart as the two long slender bolts that you removed also hold the sections of the motor together. The same when you install the new motor. It will come apart and unless you've got some experience in getting the brush holder back on the armature, it can be a problem. Don't let the motor come apart.
http://www.bikebandit.com/1980-harley-davidson-flh1200/o/m775#sch183316
Good Luck
Steve
Posted on Aug 30, 2011
There are two (2) plugs on the bottom of what looks like the large oil pan. I know it is separated on the inside and one of the plugs is for the transmission oil. Which one; left a little more towards the front or on the right sorta midway from the back.
Hi, Dude for this scenario you will need your service manual that has all fastener torque specs -fluid capacities and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at [email protected]. Good luck and have a wonderful day.
https://www.youtube.com/watch?v=k-GyRDst7Y8
http://www.mediafire.com/file/ixi9v51eb2kb99u/1998_Harley_Dyna_Service_manual.pdf/file
https://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
https://serviceinfo.harley-davidson.com/sip/service/document/6300
https://www.6ya.com/how-6ya-works to speak to me personally.
Posted on Mar 10, 2021
What are the proper front and rear tire pressures?
Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs -fluid capacities and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at [email protected]. Good luck and have a wonderful day.
https://www.hdforums.com/forum/dyna-glide-models/425361-dyna-tire-pressure.html
http://www.mediafire.com/file/l8mk1291i3fiprh/2000_Harley_FXD_Servive_Manual.pdf/file
https://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
http://mybikemanuals.com/harley-davidson/harley-davidson-dyna-glide-owners-manuals/
https://www.6ya.com/ to speak to me personally
Posted on Mar 13, 2021
starter spins but won't engage
Hi Anonymous, it sounds the like starter drive/clutch has gone south, it has components inside, that when spinning, centrifugal forces cause them to grab or lock into permanently fixed counterparts. The gear only spins one way and locks the other way. If you have one that spins both ways it has failed and needs to be replaced. Please visit the web site below for more help and good luck.
Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e
Posted on Jun 04, 2015
2000 Harley Davidson FXDWG Dyna Wide Glide what does d01clr mean? @
Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs -fluid capacities and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at [email protected]. Good luck and have a wonderful day.
https://www.hdforums.com/forum/dyna-glide-models/607772-2000-fxdx-diagnostic-trouble-codes.html
https://www.fuelmotousa.com/p-29661-harley-trouble-codes.html
http://www.mediafire.com/file/l8mk1291i3fiprh/2000_Harley_FXD_Servive_Manual.pdf/file
https://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
https://serviceinfo.harley-davidson.com/sip/service/document/6300
https://www.6ya.com/ to speak to me personally
Posted on Mar 18, 2021
how to adjust clutch inside primary case?
Solve your your problem. Check the attached links,instruction and guides, Good luck
How To Fix 5 Common Bike Issues RideApart
Motorcycle Service and Repair Manuals
http://www.carlsalter.com/motorcycle-manuals.asp
How to Diagnose Motorcycle Electrical Problems Dennis Kirk Inc
How to Diagnose Motorcycle Electrical Problems Dennis...
Electrical issues on motorcycle can...
Posted on Apr 19, 2016
How to bypass the bank angle sensor 2000 wide glide @
Hi, Bobbie a Bank Angle Sensor-Tilt Sensor-Tip Over Sensor are electrical components usually mounted around the battery area. These sensors shut down the engine when the motorcycle leans or tilts pass a specific amount of degrees from vertical. The degree angle varies from make-model-year but normally it's around 45 degrees. Recycling the ignition switch from off to on to off with the bike in the vertical position generally will reset the sensor so your engine will start again, you should refer to your owners manual for specific instructions if recycling does not work on your machine.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at [email protected]. Good luck and have a wonderful day.
https://www.hdforums.com/forum/ignition-tuner-ecm-fuel-injection/59276-how-do-you-bypass-a-bank-angle-sensor-on-a-twin-cam.html
http://www.mediafire.com/file/l8mk1291i3fiprh/2000_Harley_FXD_Servive_Manual.pdf/file
https://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
http://mybikemanuals.com/harley-davidson/harley-davidson-dyna-glide-owners-manuals/
https://www.6ya.com/
Posted on Mar 08, 2021
261 questions posted
Usually answered in minutes!
114 Questions
107 Questions
104 Questions
30 Questions
20 Questions
