20 Most Recent
2000 Harley Davidson FXDL Dyna Low Rider - Page 5 Questions & Answers
How do i time a 1986 harley fxr?put new timing
properly, remove inspection cover on left side case. the wheel is marked. TDC and the proper just before TDC I believe. with a timing light... adjust plate till you see the proper timing mark. IF IT IS TOTALLY STOCK ...off hand, put the plate in the center of its adjustment... it will run there...
you can adjust it slightly in either direction. usually it is slightly clockwise from center. when it starts right.. ride it. if it diesels.. back it off a little.
it works.
2000 HD Lowrider not getting gas to the carb. Is
no its not but most petcocks have a filter in side of them would check that first it is the bowl looking part on the bottom may have a wrench head made on it remove the bowl part after turning off the gas remove and clean or replace filter but while its off stick a paper cup under the valve and see if gas flows out if not it could be the screen on the inside. Then you have to drain the tank and unsrew the assm and check the screen
Engine match bike?
'77 would be 74" factory, who's to say it's not been bored or stroked. Only way to really tell is to pull the top end and measure.
On two seperate occassions, my 1988 HD FXRS seemed
The latter part sounds like insufficient play on the clutch lever--the clutch seems to be slipping. Sudden power loss is usually linked to the ignition system. Have you checked the lube level in the transmission? You could be having a bearing seizure if the lube is low.
Scematics for starter removal 2000 dyna fxds
Remove battery and batt box. Remove primary cover. Look for jack shaft and take off locking nut retainer. Unscrew shaft bolt. Go back over to starter side and remove 2 allen bolts. Start slides back toward you. Drink a beer.
How do i replace the jiffy stand sensor on my dyna low rider from 2008
See below. Are you aware of this recall? Do you know if the bike has been checked?
HARLEY-DAVIDSON MOTOR COMPANY
Make / Models : Model/Build Years:
HARLEY-DAVIDSON - FXD - 2009 HARLEY-DAVIDSON - FXDB - 2009 HARLEY-DAVIDSON - FXDC - 2009 HARLEY-DAVIDSON - FXDF - 2009 HARLEY-DAVIDSON - FXDL - 2009
NHTSA CAMPAIGN ID Number:
Recall Date:
DEC 10, 2008
Component:
STRUCTURE - MOTORCYCLE KICKSTAND - CENTER STAND
Potential Number Of Units Affected:
Summary:
HARLEY-DAVIDSON IS RECALLING 3,285 MY 2009 FXD, FXDF, FXDC, FXDL, AND FXDB MOTORCYCLES. THE JIFFY STAND SPRING ANCHOR MAY HAVE BEEN BUILT WITH A DEFECTIVE WELD THAT MAY ALLOW THE JIFFY STAND ASSEMBLY TO NOT RETRACT AS INTENDED.
Consequence:
HIS CONDITION COULD LEAD TO A CRASH WHICH COULD CAUSE INJURY OR DEATH TO THE RIDER.
Remedy:
DEALERS WILL REMOVE THE ORIGINAL JIFFY STAND SPRING ANCHOR AND REPLACE IT WITH A NEW SPRING ANCHOR FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN ON OR ABOUT DECEMBER 22, 2008. OWNERS MAY CONTACT HARLEY-DAVIDSON AT 1-414-342-4680.
Notes:
HARLEY-DAVIDSON RECALL NO. 0137. CUSTOMERS MAY ALSO CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION'S VEHICLE SAFETY HOTLINE AT 1-888-327-4236 (TTY 1-800-424-9153), OR GO TO HTTP://WWW.SAFERCAR.GOV.
Where can I find a
I doubt you are going to find an online repair/service manual for your Harley. Harley-Davidson is very protective of their copyrighted material. From time to time, you may see something online on the repair and servicing of H-D motorcycles but it doesn't stay there long. I would suspect that the webmaster gets a call from Harley's legal department. You can buy an OEM manual from your local shop or licensed dealers or you can get one of the other manuals such as a Clymers. Look at it this way, if you manage to fix one thing on your bike using the manual as a guide, at todays labor prices, the manual just paid for itself and the rest is free.
Good Luck
steve
How to change primary chain tension on 2007 Harley
hi,
Sooner or later, every bike will need a new chain and sprockets. Once a chain begins to wear, its pitch changes and wears the sprocket teeth. Then the chain begins to wear even faster. Then it's time for a new chain, and a new pair of sprockets.
The rear wheel on my motorcycle had been misaligned (I had used the inaccurate etched indicators on the swingarm-rather than a ruler against the sprocket-to set wheel alignment) and ridden hard through a gritty, salty winter. The rear sprocket was in rough shape, and the chain was making lots of popping sounds as the bike went down the road.
Changing a chain is a fairly basic job that requires a chain breaker / riveting tool and whatever is needed to remove the rear wheel and sprockets. It's nice to have a blow torch and a torque wrench on hand for this job, too.
The ingenious Terra-X chain tool is made in Australia out of tool steel, and weighs just 150 grams. A big hollow bolt threads into the bigger of the two holes, and is used when pressing outer plates onto new master links. A smaller bolt with a pin can thread into the hollow bolt, and is used to push link pins out of old chains or to peen new master link pins by pushing them against a grub screw threaded into the steel body's other hole. That little grub screw with a rounded steel end screws into the smaller hole of the chain breaker. It fits into and peens the hole of the new master link.
When changing a chain, the first step is to loosen the bolts on the front sprocket. It's good to get those loose while the chain is still on the bike, partly to avoid putting undue stress on the transmission, and partly to avoid getting deep into the job and finding that the front sprocket bolts are stuck. In this case, the small allen bolts needed a bit of heat to come undone.
After the bolts are loose, it's time to break the chain. With the Terra-X chain tool, you remove the small grub screw and use the small bolt with the pin to push out one of the chain's pins. No grunting or swearing required.
Then comes sprocket replacement. Six nuts on the rear sprocket, the two bolts on the front sprocket, and that step is done. I had a torque wrench handy, so I could get the torque values just right when putting everything back together.
The next step is the big one: installing the master link that joins the ends of the new chain together. The master link comes with a little bag with some X-Rings, a master link, and some sticky tan lube. Smear the lube on the pins and inside the X-Rings, then begin to assemble the master link around the two ends of the chain, making sure to get the X-Rings in the right spots.
Pressing the outer plate onto the master link is the hardest part of the job. I removed the pin bolt from the Terra-X tool and used the hollow bolt to push the outer plate onto the master link's pins. It took a few tries, but eventually I got it in the correct position.
After the sprockets are on and the master link is in position, the master link's pins need to be peened. With the Terra-X, the pin bolt pushes the master link pin against the grub screw's steel ball, and flares the pin. It takes a lot of effort-mostly because it's not easy to get a lot of leverage on tools when they're underneath a motorcycle.
Position the wheel for proper chain tension, torque everything to the correct specs, and you're back on the road. The new chain is smooth, nearly silent, and ready for thousands of miles of high-speed running.
Not finding what you are looking for?