20 Most Recent 2003 Hyosung GV 125 Aquila - Page 7 Questions & Answers


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs -fluid capacities and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Peugeot, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://answers.yahoo.com/question/index?qid=20070227134313AAKNcav
https://www.youtube.com/watch?v=d5vENUdeaRg
https://www.scribd.com/doc/88481582/Peugeot-JetForce-50-125-Workshop-Service-Repair-Manual
https://www.oemmotorparts.com/oem4.asp?M=Peugeot&T=JET%20FORCE%20%20-%2050%20cc&Y=2003&L=PE-JET_FORCE_50
https://www.manualslib.com/manual/820642/Peugeot-Jetforce.html

Motorcycles | Answered 3 hours ago


Hi, Anonymous and the usual suspects are:
1. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
2. Failed alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. A failed main circuit breaker or ignition switch, check for loose connections and continuity.
5. Failed system and or ignition relay, check for continuity.
6. Failed ignition coil, stator, magneto, ignition/electronic module.
7. Failed CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Faulty neutral, side stand or clutch lever safety switch.
10. Faulty or corroded kill switch.
11. Accelerator pump damaged or not working.
12. Water or dirt in the fuel system, carburetor or filter.
13. Restricted, blocked or kinked fuel line.
14. Fuel tank empty.
15. The gas cap is not venting properly or fuel tank venting system blocked, loosen the gas cap and go for a test ride.
16. A failed fuel pump, pressure regulator and or fuel injectors.
17. Vacuum line from the intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
18. Needle and seat stuck closed in the float bowl.
19. Petcock clogged or damaged.
20. Lean angle switch is faulty or needs adjustment.
21. Catastrophic engine failure, perform a compression test.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://www.hondahornet.org.uk/messageboard/viewtopic.php?f=60&t=32239
https://www.youtube.com/watch?v=DrI6WbKy368
https://www.carlsalter.com/honda-service-manuals.asp
https://www.partsfish.com/page/oem-parts-for-honda
https://www.manualslib.com/manual/922653/Honda-Cb600f.html

Motorcycles | Answered 3 hours ago


Hi, Guy I would love to help you with your motorcycle question but due to the magnitude of yesterday's solar flare the batteries in my crystal ball are dead and my telepathy headset circuitry was melted. I need the year, make, and model of your motorcycle please click on " Ask For More Information" directly below and provide this information in the box that will open and then click on the green "SEND" box in the bottom right-hand corner. Good luck and have a wonderful day.

Motorcycles | Answered 3 hours ago


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs -fluid capacities and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Lexmoto, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.themotorbikeforum.co.uk/viewtopic.php?t=49149
https://www.youtube.com/watch?v=y20M_yxSV3k
http://www.mychinamoto.com/forums/showthread.php?7111-Pulse-adrenaline-125-workshop-manual
https://www.chinesemotorcyclepartsonline.co.uk/microfiche/7971
https://www.bikingdirect.com/shop/lexmoto-owners-manual-pdf/

Motorcycles | Answered 3 hours ago


Hi, Anonymous the vast majority of service, parts fiche, and owners manuals on the internet are "FREE" to download and all service manuals contain specs-fluid requirements and capacities and wiring diagrams in the back pages. Another "FREE" source is online libraries you can join for a one month "FREE" trial then cancel at the end of the month. The rest usually charge a modest fee from $15-$20 and there is a handful of obscure, rare, obsolete, and very old models that are no longer or never were available, for these rare occasions I shall look on eBay and find the cheapest one available. Most of the manuals will cover your exact make, model, and year otherwise one will be provided that comes as close as possible to your bike and will have most of the same info that an exact manual would have. If there is no $ sign after the manual link it is free to download view and print.
To download your manual for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?sxsrf=ALeKk02tbdX3PsVfL3SwEEtB6uUNuxbqPg:1593931006718&source=univ&tbm=isch&q=Eurotrac+125+T+City+Lite+scooter+service+manual+pdf&sa=X&ved=2ahUKEwj6rc7bv7XqAhXjUt8KHR5WD4AQsAR6BAgKEAE&biw=1440&bih=757
https://www.monsterscooterparts.com/
http://www.family-motorsports.net/GY6-50cc-150cc.pdf

OWNER'S MANUAL

Motorcycles | Answered 3 hours ago


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs -fluid capacities and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.boltonmotorcycles.com/partFinder/fiche/honda/1990/vt250-spada/cam-chain-tensioner
https://2fiftycc.com/index.php?threads/honda-spada-vtr-250-camchain-replacement.9780/
https://issuu.com/merrillmarx/docs/honda_vt250_spada_service_repair_manual_downl.pdf
https://www.partsfish.com/page/oem-parts-for-honda
https://www.manualslib.com/manual/918333/Honda-Spada-Vt250.html

Motorcycles | Answered 4 hours ago


Hi, Will the answer to this question is way above my pay grade for this situation, I would call or visit my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts enquiry.
Good luck and have a wonderful day.

Motorcycles | Answered 4 hours ago


Hi, Ashley for this scenario you will need your service manual that has all fastener torque specs -fluid capacities and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Skyjet, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.bikechatforums.com/viewtopic.php?t=294615
https://www.youtube.com/watch?v=trAvYgEFDdM
http://capitadiscovery.co.uk/gateshead/items/489399
https://www.chinesemotorcyclepartsonline.co.uk/manufacturers/Skyjet
http://www.family-motorsports.net/GY6-50cc-150cc.pdf
https://absolutelyscooters.net/pdf/CGEN_dawg_scooter_manual.pdf

Motorcycles | Answered 4 hours ago


Hi, Ben and the usual suspects are:
1. Dirty or clogged air filter.
2. Faulty spark plug.
3. Bad Gas.
4. Improper oil level.
5. Improper chain adjustment and lubrication.
6. Low tire pressure.
7. Dirty or contaminated carburetor needs cleaning and tuning.
8. Broken carburetor spring.
9. Carburetor spring on backwards.
10. Vacuum leak on carburetor or intake boot.
11. Too much slack in the throttle cable
12. Clogged or faulty fuel pump filter or injectors.
13. Faulty pressure regulator.
14. Improper valve adjustment.
15. Slipping clutch.
16. Improper timing.
17. Low compression.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://howtomendit.com/answers.php?id=172987
https://www.scootershack.co.uk/threads/gilera-runner-vx-125-problem-losing-power.24957/
https://www.manualslib.com/manual/1014411/Gilera-Runner-50-1997.html#product-Runner%20VX125%202004
https://www.motorcyclespareparts.eu/en/gilera-parts/2003-runner-125-vx-4t-scooters
https://butminake.files.wordpress.com/2015/09/gilera-runner-user-manual.pdf

Motorcycles | Answered 4 hours ago


Hi, Anonymous you need to repost your question under the Kawasaki ATV category, not Motorcycles. Thanks, Gregg

Motorcycles | Answered 4 hours ago


Duplicate question already answered

Motorcycles | Answered 4 hours ago


Hi, Anonymous and the usual suspects are:
1. Fuel tank empty.
2. The fuel tank has old dead gas.
3. Fuel tank bottom contaminated with ethanol sludge, dirt, water, rust, etc.
4. Fuel supply valve/petcock turned off.
5. Fouled spark plugs.
6. Engine flooded as a result of overuse of the choke.
7. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
8. Fuel valve/petcock or filter clogged.
9. Fuel line to carburetor or throttle body pinched, kinked or blocked.
10. Carburetor float stuck.
11. Fuel injectors clogged.
12. Fuel injectors stuck open.
13. Quick disconnect check ball stuck.
14. Compression below 75 PSI.
15. A stuck-bent-burnt valve.
16. Improper valve clearance (too tight)
17. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a cursory reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
18. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
19. Loose or corroded wire connection at the coil or plug between ignition sensor and ECM module.
20. Spark plug cables in bad condition and shorting check for spark leakage in the dark, cable connections are loose or connected to the wrong cylinders.
21. Ignition timing incorrect due to a faulty ignition coil, ignition module or MAP, CMP, CKP, O2, TPS, ETP, IAC sensors.
22. Faulty neutral, clutch, kickstand safety switch.
23. Faulty fuel pump or fuse or relay.
24. Faulty or corroded run/stop switch.
25. Tilt sensor needs a reset.
26. Security system not disarming alarm needs a reset.
27. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://atvconnection.com/forums/1-engine-problems/340684-110-d-taotao-won-t-start.html#:~:text=If%20the%20engine%20is%20stopped,if%20the%20engine%20will%20crank.
https://www.youtube.com/watch?v=HWMUTQhyS2E
http://chineseatvmanuals.com/chinese-assorted-manuals-tao-tao-50cc-110cc-chinese-engine-service-manual-set-p-325.html
https://www.taotaopartsdirect.com/
http://chineseatvmanuals.com/chinese-assorted-manuals-taotao-ata-110-110cc-chinese-atv-owners-manual-p-257.html

Motorcycles | Answered 4 hours ago


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs -fluid capacities and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at [email protected] Good luck and have a wonderful day.
https://www.westendmotorsports.com/motorcycle-exhaust/harley-exhaust/tri-glide-exhaust/
http://www.mediafire.com/file/zysvm408rrcaij9/2012_Harley_Tri_Glide_Service_Manua.zip/file
https://www.files2zip.com/
https://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
https://ownersmanuals2.com/harley-davidson/tri-glide-ultra-classic-2012-owners-manual-66734
https://www.6ya.com/how-6ya-works to speak to me personally.

Motorcycles | Answered 4 hours ago


Hi, Erica I would love to help you with your motorcycle question but due to the magnitude of yesterday's solar flare the batteries in my crystal ball are dead and my telepathy headset circuitry was melted. I need the year, make, and model of your motorcycle please click on " Ask For More Information" directly below and provide this information in the box that will open and then click on the green "SEND" box in the bottom right-hand corner. Good luck and have a wonderful day.

Motorcycles | Answered 5 hours ago


Hi, Mika you need to repost your question under the Bank Account category, not Motorcycles. Thanks, Gregg

Motorcycles | Answered 5 hours ago


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs -fluid capacities and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://tampasportbikes.com/forum/showthread.php?62210-2001-gsxr-600-starter-removal
https://www.youtube.com/watch?v=xI4LPbLCnaU
https://www.manualslib.com/manual/1122837/Suzuki-Gsx-R600.html
https://www.partsfish.com/page/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki/suzuki-gsx-owners-manuals/

Motorcycles | Answered 5 hours ago


Hi, Anonymous I would love to help you with your motorcycle question but due to the magnitude of yesterday's solar flare the batteries in my crystal ball are dead and my telepathy headset circuitry was melted. I need the year, make, and model of your motorcycle please click on " Ask For More Information" directly below and provide this information in the box that will open and then click on the green "SEND" box in the bottom right-hand corner. Good luck and have a wonderful day.

Motorcycles | Answered 5 hours ago


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs -fluid capacities and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at [email protected] Good luck and have a wonderful day.
https://www.fuelmotousa.com/p-29661-harley-trouble-codes.html
https://www.mediafire.com/#bv2yvz0ub3olt
https://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
http://mybikemanuals.com/harley-davidson/
https://www.6ya.com/how-6ya-works to speak to me personally.

Motorcycles | Answered 5 hours ago


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs -fluid capacities and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://dirtrider.net/forums3/threads/how-much-fork-oil-in-1992-cr250.140416/
https://www.youtube.com/watch?v=FcIzfQjz-h4
https://www.carlsalter.com/honda-service-manuals.asp
https://www.partsfish.com/page/oem-parts-for-honda
https://www.manualslib.com/manual/677844/Honda-Cr250r.html
https://www.manualslib.com/manual/998674/Honda-Cr500r.html#product-CR250R

Motorcycles | Answered 5 hours ago

Not finding what you are looking for?
2003 Hyosung GV 125 Aquila Logo

9 questions posted

Ask a Question

Usually answered in minutes!

Top Hyosung Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6379 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Are you a Hyosung Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

GV 125 Aquila Hyosung

  • GV 125 Aquila Hyosung

Most Popular Question

hyosung gv 125 aquila top speed

  • Motorcycles
Loading...