2004 Husaberg Fe 650 e - Answered Questions & Fixed issues


Get a new battery. It is probably not holding a full charge overnight and only gives a weak spark when morning comes.

2004 Husaberg Fe... | Answered on Apr 13, 2009 | 367 views


Backfires are when fuel travels through the cylinders without combusting then explodes in the exhaust pipe. Fuel supply/combustion issue. It seems likely there's a problem either with the mix going into the cylinders (carbs fuel lines or air intake), or with timing. These can affect a bike at particular speeds and throttle positions. If using the choke has helped at some point that's a further indication (the choke changes the gas/air mix). ,,,

2004 Husaberg Fe... | Answered on Nov 10, 2008 | 320 views


Hi, Anonymous and the usual suspects are:
1. Fuel cap or fuel tank is not venting properly.
2. Fuel filter clogged.
3. Fuel line pinched or kinked.
4. Vacuum line from the petcock to intake manifold cracked.
5. Float needle and seat sticking.
6. Float level too low.
7. Carburetor bowl vent line clogged/blocked/pinched.
8. Idle adjusting screw set too low.
9. Air/fuel mixture screw set too lean.
10. Idle port, transfer ports, slow air jet clogged.
11. Slow fuel jet clogged.
12. Faulty fuel pump.
13. Faulty auto choke or wiring connection.
For more information about your issue and valuable "Free" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://husaberg.org/fuel/5956-only-runs-choke-any-hints.html
WHY your motorcycle only runs on CHOKE
https://www.repair-manuals.eu/cat/motorcycle_repair_workshop_manuals/repair_manuals_husaberg
http://www.cyclebuy.com/husaberg/parts.htm
https://www.manualslib.com/manual/813892/Husaberg-E-400-E.html#product-FC%20550/4

Husaberg... | Answered on Jun 13, 2019 | 44 views


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Husaberg, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?q=Replace+the+battery+2002+husaberg+470-fxe&source=lnms&tbm=isch&sa=X&ved=0ahUKEwjHooyGkObiAhXqqFkKHcIWB3kQ_AUIESgC&biw=1440&bih=757
http://husaberg.org/electrical/9274-new-owner-fx-470-2002-battery-replacement-question.html
http://husaberg.org/mechanical/11215-workshop-manual.html
http://www.cyclebuy.com/husaberg/parts.htm
https://www.manualslib.com/manual/640214/Husaberg-05.html

Husaberg... | Answered on Jun 13, 2019 | 50 views


The main fuse protects all power consumers of the vehicle. It is located in the starter relay housing under the air filter box lid. (A spare fuse is located in the starter relay)

The fuse box containing the fuses of individual power consumers is located under the seat

Husaberg... | Answered on Feb 26, 2017 | 56 views


Hi, Pete and the usual suspects are:
1. Severely drained or faulty battery.
2. Faulty regulator/rectifier or high output coil.
3. Faulty power valve, solenoid or installation.
4. Clogged air filter or exhaust.
5. Cracked or incorrect float level.
6. Float needle is not seating.
7. Faulty reed valve.
For more information about your question please visit the website below. Good luck and have a nice day.
HUSABERG Pure Enduro Service

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Husaberg... | Answered on Nov 11, 2015 | 75 views


Its a long shot, but try Youtube.
They have tons of DIY videos.

Husaberg... | Answered on Jan 08, 2015 | 66 views


Basically the only way water can get in the oil is if there is a corrosion hole in the housing behind the pump impellor. Water pumps have only 1 seal and if that leaks water will drain from a hole in the pump housing under neath the pump.

Husaberg... | Answered on Mar 11, 2013 | 297 views


apparently it is telling you there is 'No Support' for the vehicle or the function you are trying to test like ABS braking system.

https://www.amazon.com/Innova-3020d-Severity-Emissions-Diagnostics/product-reviews/B07BM9YQBB?reviewerType=all_reviews

Manual_3020a_E.pdf - Innova.com

csr.innova.com > Content > Manual > Innova

PDF Not all vehicles support all fifteen Monitors. When the. Code Reader is linked to a vehicle, only the icons for Monitors that are supported by the vehicle under test ...

Motorcycles | Answered 16 hours ago | 11 views


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs -fluid capacities and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at [email protected] Good luck and have a wonderful day.
https://www.google.com/search?sxsrf=ALeKk00BZQnv4NHUXf-frogVqxFERQK57w:1600932109334&source=univ&tbm=isch&q=1975+harley+fxe+fuse+box+location&sa=X&ved=2ahUKEwjfhr7toIHsAhVBu1kKHZV6ArMQjJkEegQIBRAB&biw=1440&bih=757
http://www.mediafire.com/file/g9b5qc86j56cqlu/1975__Harley_FXE_Service_Manual.pdf/file
https://www.jpcycles.com/1975-harley-davidson-super-glide-electric-start-fxe
http://mybikemanuals.com/harley-davidson/
https://www.6ya.com/how-6ya-works to speak to me personally.

Motorcycles | Answered 24 hours ago | 56 views


Motorcycles | Answered Yesterday | 28 views


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs -fluid capacities and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Suzuki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.dirtbikeaddicts.com/content/threads/ds80-kick-start-shaft-replacement.10204/
https://www.youtube.com/watch?v=FZ0qiMVq1Vo
https://www.tradebit.com/filedetail.php/277569821-1981-1982-1983-1984-1985-1986-1987 $15
https://www.partsfish.com/page/oem-parts-for-suzuki
https://issuu.com/rudy72ralodi/docs/suzuki_ds_80_owners_manual

Motorcycles | Answered Yesterday | 1,023 views


Hi, Anonymous and the usual suspects are:
1. Improper clutch adjustment or not disengaging.
2. Bent shift shaft.
3. Shift fork bent or seized.
4. Gear seized on the shaft.
5. Gear positioning lever binding.
6. Shift return springs weak or broken.
7. Shift return spring pin loose
8. Shift mechanism arm spring is broken.
9. Shift mechanism arm is broken.
10. Shift drum is broken.
11. Shift lever loose on the shift shaft.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://thumpertalk.com/forums/topic/580498-coolster-xr2-125-shifting-from-stop-problem/
https://www.youtube.com/watch?v=FdXsWDaVSZQ
https://coolster.com/manuals-diagrams/
https://coolster.com/shop/sort-by-vehicle-model/dirt-bike-parts/
https://wmsbrighton.freshdesk.com/support/solutions/articles/19000095328-coolster-dirt-bike-owner-s-manual-downloads

Motorcycles | Answered Yesterday | 93 views


Hi, Anonymous and the usual suspects are:
1. Spark plugs in bad condition or have an improper gap or are partially fouled.
2. Spark plug cables in bad condition.
3. Battery damaged or nearly discharged, should have 12.5 volts.
4. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Throttle controls not adjusted correctly.
6. Water or dirt in the fuel system.
7. Water or dirt in the carburetor.
8. Intake air leak.
9. Fuel tank vent hose and vapor valve plugged, or the fuel line is closed off, restricting fuel flow.
10. Choke valve inoperative.
11. Engine lubricant to heavy (winter operation).
12. Ignition is not functioning properly (possible sensor failure).
13. Faulty ignition coil.
14. Valves sticking.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://www.migcruisers.com/Jim/Hard_To_Start_Marauder_VZ800.pdf
https://www.youtube.com/watch?v=O-lSk-9Imfw
https://www.manualslib.com/manual/824096/Suzuki-Vz800.html
https://www.partsfish.com/page/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki/

Motorcycles | Answered Yesterday | 15 views


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs -fluid capacities and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Big Dog, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.bigdogbiker.com/threads/how-to-adjust-your-clutch-05-and-newer.2025/
https://www.youtube.com/watch?v=kFasAn8qG4A
https://www.motorcycle-manual.com/big-dog/
https://mobile-global-apps-storage.life/away.php
https://www.bigdogbiker.com/threads/2007-big-dog-pitbull-owners-manual-and-service-manual.72901/

Motorcycles | Answered Yesterday | 45 views


Hi, Anonymous and the usual suspects are:
1. Low coolant level.
2. Restricted radiator airflow.
3. Faulty thermostat.
4. Coolant pump or fans inoperative.
5. Vent hose crimped.
6. The air in the coolant and needs bleeding.
7. Engine idling too long or bike moving too slow.
8. Coolant too old needs to be replaced.
9. Faulty temperature sensor, wiring or connector.
10. Radiator veins clogged or corroded needs repair
11. Cooling system leak.
12. Ignition timing retarded.
13. Spark plug heat range too high.
14. Faulty radiator cap.
15. Carburetor jetted too lean.
16. Damaged top end.
17. Blown head gasket.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.honestjohn.co.uk/forum/post/index.htm?t=45162
https://www.motorcycleforum.com/threads/help-please-03-yzf600r-overheating-issue.89598/
https://www.manualslib.com/manual/1003225/Yamaha-Yzf750r.html
https://www.partsfish.com/page/oem-parts-for-yamaha
http://mybikemanuals.com/yamaha/yamaha-yz-owners-manuals/

Motorcycles | Answered Yesterday | 50 views


Hi, Anonymous and the usual suspects are:
1. Fouled spark plugs.
2. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Loose connection at ignition coil or plug between ignition sensor and module.
5. Spark plug cables in bad condition, shorting/leaking, spark plug cable connections loose check for spark leakage in the dark.
6. A faulty ignition coil or electronic control module.
7. Faulty pulse coil.
8. Faulty CKP, CMP, or BAS sensor.
9. Faulty ignition switch.
10. Faulty run/off switch
11. Tilt sensor needs a reset.
12. Security alarm failing to disarm needs reset
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.buggydepot.com/tech-center/gy6-150cc-ignition-troubleshooting-guide-no-spark/
https://www.youtube.com/watch?v=UU4S0Ov9q4c
http://www.family-motorsports.net/GY6-50cc-150cc.pdf
https://www.scooterdynasty.com/stockoempartsforscooters-14.aspx
https://www.manualslib.com/manual/1054464/Vento-Phantom-R4i.html
https://absolutelyscooters.net/pdf/CGEN_dawg_scooter_manual.pdf

Motorcycles | Answered Yesterday | 77 views


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs -fluid capacities and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at [email protected] Good luck and have a wonderful day.
https://www.google.com/search?sxsrf=ALeKk00MJDJRB9aLDBtcnYwhVxQkeuKDcg:1600928332381&source=univ&tbm=isch&q=2011+blackline+fxs+softail+wiring+diagram&sa=X&ved=2ahUKEwjoq7_kkoHsAhXDzlkKHVU4Af8QjJkEegQICxAB&biw=1440&bih=757
http://www.mediafire.com/file/stfcd12titrddjv/2011+Harley+Softail+Service+Manual.pdf
https://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
https://ownersmanuals2.com/harley-davidson/blackline-2011-owners-manual-66670
https://www.6ya.com/how-6ya-works to speak to me personally.

Motorcycles | Answered Yesterday | 98 views


What is your question?

Motorcycles | Answered Yesterday | 39 views


Hi, Anonymous the answer to this question is way above my pay grade for this situation, I would call or visit my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts enquiry.
Good luck and have a wonderful day.

Motorcycles | Answered Yesterday | 243 views

Not finding what you are looking for?
2004 Husaberg Fe 650 e Logo

4 questions posted

Ask a Question

Usually answered in minutes!

Top Husaberg Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6480 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Bill Boyd

Level 3 Expert

53816 Answers

Are you a Husaberg Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...