20 Most Recent 2000 Husaberg Fe 600 Questions & Answers


Hi, Cheyneweathe and the usual suspects are:
1. Fuel tank empty.
2. The fuel tank has old dead gas.
3. Fuel tank bottom contaminated with ethanol sludge, dirt, water, rust, etc.
4. Fuel supply valve/petcock turned off.
5. Fouled spark plugs.
6. Engine flooded as a result of overuse of the choke.
7. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
8. Fuel valve/petcock or filter clogged.
9. Fuel line to carburetor or throttle body pinched, kinked or blocked.
10. Carburetor float stuck.
11. Fuel injectors clogged.
12. Fuel injectors stuck open.
13. Quick disconnect check ball stuck.
14. Compression below 75 PSI.
15. A stuck-bent-burnt valve.
16. Improper valve clearance (too tight)
17. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a cursory reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
18. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
19. Loose or corroded wire connection at the coil or plug between ignition sensor and ECM module.
20. Spark plug cables in bad condition and shorting check for spark leakage in the dark, cable connections are loose or connected to the wrong cylinders.
21. Ignition timing incorrect due to a faulty ignition coil, ignition module or MAP, CMP, CKP, O2, TPS, ETP, IAC sensors.
22. Faulty neutral, clutch, kickstand safety switch.
23. Faulty fuel pump or fuse or relay.
24. Faulty or corroded run/stop switch.
25. Tilt sensor needs a reset.
26. Security system not disarming alarm needs a reset.
27. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://husaberg.org/fuel/2325-2000-fe600-wont-start-hot-especially-if-i-drop.html
What To Do If Your Motorcycle Doesn Start
http://www.keustermans.nl/Husaberg_FE600_99_repair_manual.pdf
http://www.cyclebuy.com/husaberg/parts.htm
https://www.manualslib.com/manual/1088074/Husaberg-Enduro-Fe-400.html#product-ENDURO%20FE%20600

2000 Husaberg Fe... | Answered on Jun 13, 2019


you need a micrometere or vernier caliper to measure how thick they are that how you tell how worn the clutch is. the manual will list the specificational limit (how thin you should allow them to get and how do the basket and innser hub looks like). if they have small teeth on them they are worn.,

2000 Husaberg Fe... | Answered on Nov 10, 2008


ProClean is good stuff but not worth the money. The only reason I had it was because I won a create of it at our clubs Supercross race it's too expensive in my opinion. I buy 40 litre containers of stuff called TFR which stands for Traffic Film Remover, it basically is a detergent like ProClean, Simple Green and all the others, only it costs a fraction of the price and isn't deluted. This means you can delute it to your own strength for different causes. You can see it removing dirt as you watch, like someone said above. You can not use it pure on the bike however, it will make alloy parts go dull - as my buddy found out lol. ,,,

2000 Husaberg Fe... | Answered on Nov 10, 2008


i always just put some on the o-ring before i put it back in but no you dont need to have oil on it,

2000 Husaberg Fe... | Answered on Nov 10, 2008


depends on what material is stained.. Aluminium stains can be very tricky to get clean if not impossible...some cleaners will also cause a orange/reddish stain wich will not come out unless you use some harsh chemicals to get them out. problem is it's hard to get to those chemicals. IF you happen to have a truck wash nearby where they wash the big trucks (18 wheelers)take your parts there and tell them to use some brightener on it it's a chemical that really cleans aluminium.it may cost you a little bit of money but that stuff really works and i haven't been able to find that stuff for private sale anywhere. the number 2 reasons for stains on the bike are : 1) waiting to long to wash the bike some types of sand/mud especially the red dirt we have down south here will stain a bike if you leave it on the bike not only that it dries as hard as concrete and is very difficult to remove , so was your bike ASAP. 2) washing chemicals. Some chemicals / soaps when they are left too long on aluminium will leave stains as it reacts with the aluminium , these stains are almost impossible to get out. ,,,

2000 Husaberg Fe... | Answered on Nov 10, 2008


and had the bike souped for it. Anyway the throttle is SUPER touchy.. You breath on it and it takes off.. Because of this I ended up dumpin it 30 min after I got on..haha... My question is is there a way to stiffen up the throttle so that i have to crank the grip harder to give it gas? I am very inexperienced, and when it took off, i tensed up, hittin the throttle even harder. I know i will appreciate the the responsiveness when I get more experience, but i dont want to die in the process..lol.. thanks for you help! ,UYou need to learn to hold on to the bike with your legs, so you aren't pulling on the bars during acceleraion. The throttles are supposed to be easy to turn, so that it will snap completely closed when you let off. You can replace the throttle cam (the part that the cable attaches to) with a slower-opening unit that will give you more control. The amount you have to turn the throttle from closed to full-open will stay thesame, but it will open slower in the first half of the throttle pull, keeping you from getting such an abrupt surge of power. Once you get a little more time on the bike, you won't have this issue any longer. You will learn proper throttle control, and your wrist will get used to the throttle pull. ,,,

2000 Husaberg Fe... | Answered on Nov 10, 2008


Hi, Anonymous and the usual suspects are:
1. Fuel cap or fuel tank is not venting properly.
2. Fuel filter clogged.
3. Fuel line pinched or kinked.
4. Vacuum line from the petcock to intake manifold cracked.
5. Float needle and seat sticking.
6. Float level too low.
7. Carburetor bowl vent line clogged/blocked/pinched.
8. Idle adjusting screw set too low.
9. Air/fuel mixture screw set too lean.
10. Idle port, transfer ports, slow air jet clogged.
11. Slow fuel jet clogged.
12. Faulty fuel pump.
13. Faulty auto choke or wiring connection.
For more information about your issue and valuable "Free" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://husaberg.org/fuel/5956-only-runs-choke-any-hints.html
WHY your motorcycle only runs on CHOKE
https://www.repair-manuals.eu/cat/motorcycle_repair_workshop_manuals/repair_manuals_husaberg
http://www.cyclebuy.com/husaberg/parts.htm
https://www.manualslib.com/manual/813892/Husaberg-E-400-E.html#product-FC%20550/4

Husaberg... | Answered on Jun 13, 2019


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Husaberg, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?q=Replace+the+battery+2002+husaberg+470-fxe&source=lnms&tbm=isch&sa=X&ved=0ahUKEwjHooyGkObiAhXqqFkKHcIWB3kQ_AUIESgC&biw=1440&bih=757
http://husaberg.org/electrical/9274-new-owner-fx-470-2002-battery-replacement-question.html
http://husaberg.org/mechanical/11215-workshop-manual.html
http://www.cyclebuy.com/husaberg/parts.htm
https://www.manualslib.com/manual/640214/Husaberg-05.html

Husaberg... | Answered on Jun 13, 2019


The main fuse protects all power consumers of the vehicle. It is located in the starter relay housing under the air filter box lid. (A spare fuse is located in the starter relay)

The fuse box containing the fuses of individual power consumers is located under the seat

Husaberg... | Answered on Feb 26, 2017


Hi, Pete and the usual suspects are:
1. Severely drained or faulty battery.
2. Faulty regulator/rectifier or high output coil.
3. Faulty power valve, solenoid or installation.
4. Clogged air filter or exhaust.
5. Cracked or incorrect float level.
6. Float needle is not seating.
7. Faulty reed valve.
For more information about your question please visit the website below. Good luck and have a nice day.
HUSABERG Pure Enduro Service

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Husaberg... | Answered on Nov 11, 2015


Its a long shot, but try Youtube.
They have tons of DIY videos.

Husaberg... | Answered on Jan 08, 2015


Basically the only way water can get in the oil is if there is a corrosion hole in the housing behind the pump impellor. Water pumps have only 1 seal and if that leaks water will drain from a hole in the pump housing under neath the pump.

Husaberg... | Answered on Mar 11, 2013


Hi, Christopher for this scenario you will need your service manual that has all fastener torque specs -fluid capacities and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://goldwingdocs.com/forum/viewtopic.php?t=14251
https://www.youtube.com/watch?v=_fKe5QglIQY
https://www.manualslib.com/manual/1069155/Honda-Goldwing-Gl1100.html
https://www.partsfish.com/page/oem-parts-for-honda
https://www.manualslib.com/manual/1022151/Honda-Gold-Wing-Gl1100.html

Motorcycles | Answered Yesterday


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs -fluid capacities and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?sxsrf=ALeKk02b65sTZKw2_cshcMeEiSzfxxf5Cw:1594395296228&source=univ&tbm=isch&q=honda+wave+100+wiring+diagram&sa=X&ved=2ahUKEwi3zIyqgcPqAhUmmuAKHZM3DSMQsAR6BAgKEAE&biw=1440&bih=757
https://www.pinterest.com/pin/825636544167746825/
http://www.family-motorsports.net/GY6-50cc-150cc.pdf
https://www.partsfish.com/page/oem-parts-for-honda
https://absolutelyscooters.net/pdf/CGEN_dawg_scooter_manual.pdf

Motorcycles | Answered Yesterday


Hi, JB before diagnosing your blown fuse issue, check the bottom of your seat, if its metal and comes in close proximity to the positive battery post you need to take the necessary steps to ensure there is no contact (electrical tape, thick rubber insulation, hammer a dent in the seat bottom, etc.) You are going to need a wiring diagram from your service manual, a test light, an ohmmeter and plenty of extra fuses.
If you turn on your ignition switch and immediately blow a fuse you have a hard/dead short and is usually easy to find. With a test light connected to the hot side of the blown fuse holder start stabbing the wire/s that leads away from the fuse holder and towards the ignition switch, you test light will illuminate validating the short. When the test light fails to illuminate you have passed the short and need to back up until the test light illuminates, then look in the immediate area for the short.
If you driving down the road for 30 minutes or 15 miles and blow a fuse you have soft/flying short and may take some time and patience to find.
If the main fuse/circuit breaker constantly blows/trips while riding you probably have a faulty battery terminal connection. Check battery terminals for damage or corrosion, check battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary. Any other fuses that constantly keep blowing while riding are usually caused by a loose or corroded ground wire in the circuit, which means you have to check, inspect, test each and everyone with an ohmmeter set on a low ohm scale 100 ohms or less . Simply touch one lead to the ground source and the other lead to the battery negative terminal, a reading of zero indicates a clean solid ground. Any reading or infinity indicates a poor ground and needs to be repaired. Poor or weak grounds require excessive additional amperage to complete the circuit which in turn blows the small amperage fuse.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://kzrider.com/forum/4-electrical/538225-main-fuse-getting-real-hot-and-blowing
https://www.youtube.com/watch?v=kw11Onl7OLQ
https://bitbin.it/4OxDef39/
https://www.partsfish.com/page/oem-parts-for-kawasaki
https://www.zigwheels.ph/new-motorcycles/kawasaki/barako-ii/specifications

Motorcycles | Answered Yesterday


Hi, Haydn, I would love to help you with your motorcycle question but due to the magnitude of yesterday's solar flare the batteries in my crystal ball are dead and my telepathy headset circuitry was melted. I need the year, make, and model of your motorcycle please click on " Ask For More Information" directly below and provide this information in the box that will open and then click on the green "SEND" box in the bottom right-hand corner. Good luck and have a wonderful day.

Motorcycles | Answered Yesterday


Hi, Anonymous you need to repost your question under the Bandit Stump Grinder category, not Motorcycles. Thanks, Gregg

Motorcycles | Answered Yesterday


Hi, Anonymous the vast majority of service, parts fiche, and owners manuals on the internet are "FREE" to download and all service manuals contain specs-fluid requirements and capacities and wiring diagrams in the back pages. Another "FREE" source is online libraries you can join for a one month "FREE" trial then cancel at the end of the month. The rest usually charge a modest fee from $15-$20 and there is a handful of obscure, rare, obsolete, and very old models that are no longer or never were available, for these rare occasions I shall look on eBay and find the cheapest one available. Most of the manuals will cover your exact make, model, and year otherwise one will be provided that comes as close as possible to your bike and will have most of the same info that an exact manual would have. If there is no $ sign after the manual link it is free to download view and print.
To download your manual for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?sxsrf=ALeKk00FQSOFf7aYJuJQRhoY2L8cNGh6-w:1594394054266&source=univ&tbm=isch&q=Rear+swingarm+assembly+parts+diagram+Yamaha+pw80&sa=X&ved=2ahUKEwjGyvHZ_MLqAhVhkuAKHfNzBk8QsAR6BAgJEAE&biw=1440&bih=757
https://www.bikebandit.com/oem-parts/1983-yamaha-pw80-pw80k-swingarm-rear-shocks/o/m147070sch212569
https://www.manualslib.com/manual/581554/Yamaha-Pw80-P.html
https://www.partsfish.com/page/oem-parts-for-yamaha
https://www.manualslib.com/manual/581541/Yamaha-Pw80-X.html

Motorcycles | Answered Yesterday


Hi, Anonymous derestrict is a negative term rider's use to express their wish to improve performance on their bike or scooter. Depending on the country and motor vehicles laws some bikes and scooters are designed to conform with said laws and their performance is slightly lower than other countries. All vehicles in the world are designed to perform at 75-80% of their maximum potential, this ensures the longevity of the engine. Derestricting or improving performance is always possible on any vehicle but the tradeoff of engine longevity numbers go down, how much depends on the number and type of performance upgrades. Your local dealership or reputable independent shop are best equipped to provide you with technical data and willingness to comply with your needs.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://korider.com/index.php?topic=5102.0
https://www.bikechatforums.com/viewtopic.php?t=127108
https://www.manualslib.com/manual/406853/Hyosung-Comet-125.html
https://www.hyosungwholesale.com/collections/gt125r
https://www.manualslib.com/manual/803358/Hyosung-Comet-250-R.html#product-COMET%20125%20-%20SERVICE

Motorcycles | Answered Yesterday


Hi, Anonymous and the usual suspects are:
1. Spark plugs in bad condition or have an improper gap or are partially fouled.
2. Spark plug cables in bad condition.
3. Battery damaged or nearly discharged, should have 12.5 volts.
4. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Throttle controls not adjusted correctly.
6. Water or dirt in the fuel system.
7. Water or dirt in the carburetor.
8. Intake air leak.
9. Fuel tank vent hose and vapor valve plugged, or the fuel line is closed off, restricting fuel flow.
10. Choke valve inoperative.
11. Engine lubricant to heavy (winter operation).
12. Ignition is not functioning properly (possible sensor failure).
13. Faulty ignition coil.
14. Valves sticking.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.kawasakiforums.com/forum/general-tech-9/very-confused-wont-start-ke100-11056/
https://thumpertalk.com/forums/topic/1287286-kawasaki-ke-100-wont-start/
https://www.tradebit.com/filedetail.php/281558262-kawasaki-ke100-motorcycle-complete-workshop-service-repair $20
https://www.partsfish.com/page/oem-parts-for-kawasaki
https://ownersmanuals2.com/kawasaki/ke100-1988-owners-manual-53102

Motorcycles | Answered Yesterday

Not finding what you are looking for?
2000 Husaberg Fe 600 Logo

10 questions posted

Ask a Question

Usually answered in minutes!

Top Husaberg Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6386 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Bill Boyd

Level 3 Expert

53812 Answers

Are you a Husaberg Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Fe 600 Husaberg

  • Fe 600 Husaberg

Most Popular Question

1999 husaberg fe not starting

  • Motorcycles
Loading...