20 Most Recent 1983 Honda vt 500 ft ascot - Page 3 Questions & Answers


clutch slipping, splines on drive shaft worn,thottle setting too high

Honda vt 500 ft... | Answered on Jul 04, 2010


sounds like the new used one is bad too. The only thing that regulates voltage is the rectifier.

Honda vt 500 ft... | Answered on Oct 14, 2009


SOURCE: scoopy
There is a fuel shutoff valve on the bottom of the tank that stops fuel flow when the engine is not running.
At a guess while the scooter was in storage the fuel evaporated from the carby and fuel lines. Now you are trying to start it again the fuel is slowly flowing down to the carby but not fast enough to fill the carby and start the engine.
You are probably close to starting if you cranked it for about 1 minute.
Three posibilities, keep cranking, keep adding fuel to the inlet to keep it kicking over until the carby gets fuel or take the vacuum line off the carby and suck on it for a while to let the fuel flow down to the carby.
Either way you should be close to it starting assuming its just the fuel shortage in the carby.

Honda... | Answered 2 days ago


Yes, most voltage regulators are internal in todays alternators. There are automotive electric repair shops that can replace or repair parts inside of your alternator that will usually cost less than replacing the alternator. The problem is that you have to take the bad alternator to the place and typically drop it off for however long it takes them to get to it. Most people would tell you to just replace it.

Honda... | Answered on Dec 30, 2020


Sitting on the bike #1 Left Rear #2 Left Front #3 Right Rear #4 Right Front

Honda... | Answered on Dec 29, 2020


https://www.youtube.com/watch?v=hHD47CbnH5k THIS VIDEO LINK WILL PROVIDE YOU COMPLETE INFORMATION ABOUT YOUR QUESTION.

Honda... | Answered on Dec 25, 2020


If it will not spin over at all I'd check the battery and starter connections and battery state of charge first .

Honda... | Answered on Nov 25, 2020


maybe nos or junkyard. its gonna be a long search for you. check e bay also...good luck

Honda... | Answered on Nov 17, 2020


To run a petrol internal combustion engine it requires four things.
Air
Fuel
Compression
Ignition.
Which is missing ...............................

Honda... | Answered on Nov 13, 2020


Valve clearance need adjusting a fraction. not dangerous, better to be a tad loose than too tight and have valves partially open.

Google

year make model adjust valve clearance

It's an easy job and will take 15 minutes with basic tools and a feeler gauge.

https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&sxsrf=ALeKk03IHsZ6iXxD-60eHjyK0Amn6xmIrA%3A1604713857741&ei=gf2lX-LfLNXQtQaV77ww&q=honda+160cc+valve+adjustment

..

Honda... | Answered on Nov 07, 2020


<a href="https://portabledownloads.com/maxon-cinema-4d-studio-r22-with-crack/ "> Maxon Cinema 4D </a> Maxon CINEMA 4D Studio R22 With Crack Introduces powerful new tools, opportunities, and improvements in modeling, animation, and shading. The perfect package for all 3D artists, both beginners and professionals. It has a wide range of tools and resources to quickly achieve impressive
<a href="https://windowcrack.com/pixologic-zbrush-2020-1-3-crack// "> Pixologic Zbrush </a>

Honda... | Answered on Nov 03, 2020


Hi, Rene for this scenario you will need your service manual that has all fastener torque specs -fluid capacities and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://itstillruns.com/remove-honda-shadow-starter-5007585.html
https://www.hondashadow.net/threads/starter-removal-on-vt1100-shadow.434250/
https://www.manualslib.com/manual/1188474/Honda-Shadow-Vt1100.html
https://www.partsfish.com/page/oem-parts-for-honda
https://www.manualslib.com/manual/899170/Honda-Shadow-Vt1100.html

Honda... | Answered on Nov 02, 2020


Hi, Benny for this scenario you will need your service manual that has all fastener torque specs -fluid capacities and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?sxsrf=ALeKk00Ke070HT_38mpoB7-cEtaQ5ULDew:1604340664889&source=univ&tbm=isch&q=Shifter+will+not+return+to+its+proper+place+honda+tmx+125&sa=X&ved=2ahUKEwiaobfbuuTsAhXqt1kKHW31BboQjJkEegQIAhAB&biw=1440&bih=757
https://www.youtube.com/watch?v=PJtElClDQrM
http://onthelastepisode.com/forums/topic/honda-tmx-125-alpha-service-manual/
https://www.partsfish.com/page/oem-parts-for-honda
https://www.manualslib.com/manual/1638127/Honda-Wave-110-Alpha-2018.html#product-TMX%20125a%202018

Honda... | Answered on Nov 02, 2020


Hi, Mike for this scenario you will need your service manual that has all fastener torque specs -fluid capacities and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?sxsrf=ALeKk01Okl2d16DczFcHcoO5tIe34ytNsA:1604247315638&source=univ&tbm=isch&q=How+to+remove+the+flywheel+Honda+TMX+155&sa=X&ved=2ahUKEwjPhYX73uHsAhWlp1kKHZHXBSgQjJkEegQIERAB&biw=1440&bih=757
https://www.youtube.com/watch?v=B7Ne2yPgIqk
http://www.magnariders.cz/files/hcsm.pdf
https://www.partsfish.com/page/oem-parts-for-honda
https://www.manualslib.com/manual/1681597/Honda-Tmx-Supremo-Series.html

Honda... | Answered on Nov 01, 2020


Hi, Verna you need to repost your question under the Honda Generator category, not Motorcycles. Thanks, Gregg

Honda... | Answered on Nov 01, 2020


Hi, Leoveli the vast majority of service, parts fiche, and owners manuals on the internet are "FREE" to download and all service manuals contain specs-fluid requirements and capacities and wiring diagrams in the back pages. Another "FREE" source is online libraries you can join for a one month "FREE" trial then cancel at the end of the month. The rest usually charge a modest fee from $15-$20 and there is a handful of obscure, rare, obsolete, and very old models that are no longer or never were available, for these rare occasions I shall look on eBay and find the cheapest one available. Most of the manuals will cover your exact make, model, and year otherwise one will be provided that comes as close as possible to your bike and will have most of the same info that an exact manual would have. If there is no $ sign after the manual link it is free to download view and print.
To download your manual for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://piesuccesadd.files.wordpress.com/2015/10/honda-wave-100r-service-manual.pdf
https://www.partsfish.com/page/oem-parts-for-honda
https://www.manualslib.com/manual/826702/Honda-Wave-110i.html
https://bikez.com/motorcycles/honda_wave_100_2013.php
https://en.wikipedia.org/wiki/Honda_Wave_series

Honda... | Answered on Nov 01, 2020


Do the plugs spark out of the engine so you can see ...

Honda... | Answered on Oct 30, 2020


A too tight tappet adjustment can do more than reduce mileage - it effectively changes the valve timing and can lead to burned valves and seats.

It is best not to prejudge such situations - it is generally believed the expansion of metals when the engine is at working temperature causes the tappet clearance to reduce. This isn't always the case when an aluminium cylinder head is used. Aluminium expands a much greater amount than steel and so working temperature can cause the valve clearances to increase.

Honda... | Answered on Oct 30, 2020


This sounds like it may be a vacuum leak. When more air than normal is leaking into the engine, the idle will be higher than normal. The easiest way to find a vacuum leak is to take some carburetor cleaner or WD-40 and spray it around the areas where you suspect a leak may exist. If the engine idle goes up when you spray, there is a leak around that area.

Honda... | Answered on Oct 29, 2020

Not finding what you are looking for?
1983 Honda vt 500 ft ascot Logo

47 questions posted

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6523 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

217 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

vt 500 ft ascot Honda

  • vt 500 ft ascot Honda

Most Popular Question

much oil add honda vt 500 motorcycle

  • Motorcycles
Loading...