2001 Cagiva Raptor 650 - Answered Questions & Fixed issues
What oil fits best my bike?
Stick with the major brands; Pennzoil, Quaker State, Mobil or Shell. 10w40 is what goes in the engine. I am not familiar with the Cagiva brand motorcycle, but you probably have an oil dipstick on the end of the oil filler cover. Fill the gearbox until the oil is mid-point in the indicated range, probably 3 quarts will do.
Change the oil filter also, (assuming the bike has one). Recheck oil level after running the engine for a minute. This allows the oil filter to fill up. Often the oil capacity is shown right next to the oil filler hole. If there is no dipstick and no oil capacity information at the filler hole then best to contact the dealer and ask.
Please rate this answer. Thanks Octavia! < nice name
4/6/2009 1:47:52 PM •
2001 Cagiva...
•
Answered
on Apr 06, 2009
•
410 views
Genral oil change
1.Get your supplies ready and expose your engine
2.Unscrew the Oil Filler Cap
3.Remove the Oil Drain Plug
4.Remove and Replace the Crush Washer
5.Clean the Oil Drain Plug
6.Remove the Oil Filter
7.Remove and Clean Plastic Mesh Filter
8.Lubricate the O-ring of the New Filter and Attach it to the Engine
9.Motorcycle Oil Change - Replace Oil Drain Plug & Plastic Mesh Filter Pour Oil
10.Check the Oil Level,,
11/10/2008 4:51:06 PM •
2001 Cagiva...
•
Answered
on Nov 10, 2008
•
134 views
Brake dust removal
long-armed brush is usually the best way scrub off brake dust and dirt. Apply a wheel cleaner first and let it settle before scrubbing it off. Chrome wheels will require specific cleaners so be aware of your wheel's finish before purchasing a cleaner.
Don't use tire dressing products as their glossy finishes can compromise grip,,
11/10/2008 4:51:05 PM •
2001 Cagiva...
•
Answered
on Nov 10, 2008
•
93 views
I Have 2013 350 raptor wont start. Replaced ignition coil and ici box and spark plug.. No spark. Still wont turn over
You have written some conflicting information. How can you know that your engine has no spark if it will not turn over? No problem, please write back and elaborate on its issue, symptoms, engine codes and things you have checked and tested so far. At this point I would start looking around. Inspect the battery and power distribution box. Check that the battery connections are clean and tight. Check that the ground cable, going to the body panel is clean and tight. Check all the fuses for damage (over heating or corrosion) and the same for the relays. Is the antitheft system working (does it recognize your ignition key?)? When you turn the ignition hey to the RUN position. Does the gauge cluster respond like it always does? Do you see the lights come on and go out and can you read the odometer mileage? Please write back and let me know. Good Luck.
9/20/2018 3:45:56 AM •
Cagiva...
•
Answered
on Sep 20, 2018
•
65 views
How do you set up timing on a cagiva river 600
Remove the side cover so you can have access to the stator. Then you will be looking for a notch on the inner case. Once you locate the notch you will line up the stator ( which also has a little line or notch on it ) with that notch.
10/20/2016 2:09:26 PM •
Cagiva...
•
Answered
on Oct 20, 2016
•
303 views
CAGIVA CANYON 500 MANUAL
Hello, you need to use manual? If so, the best return to the original car, and you are interested in motorcycle aspects? If you can, you have time to look at.http://www.motorpartstore.com.Good luck and have a nice day
4/9/2016 6:52:01 AM •
Cagiva...
•
Answered
on Apr 09, 2016
•
135 views
Dies when put in gear
Check the kickstand interlock switch. As deemed mandatory by the DOT.. all street legal motorcycles come with a switch in the kickstand pivot area that detects whether or not it is in the upright (or down) position. This is supposed to prevent riders from taking off with the kickstand down, which can ruin your day when the first left hander comes up- This switch will essentially shutdown the electrics to the engine once you attempt to engage first gear (in the down position)...These switches are fairly reliable but can fail. To test it, take a small jumper wire and connect the two wires (going to the switch) together.
1/29/2016 4:43:49 PM •
Cagiva...
•
Answered
on Jan 29, 2016
•
61 views
I need to replace the left tail fairing and I need to know if I can use one from an older model
Possibly depends if your model is still being made or find out if not when the style and looks changed after your year an usually you find bits like fairings exhausts etc are interchangeable from earlier models but not to disshearten you but being cagiva or aprillia you need the same year or atleast model from when it was started until next model changed hope it helps pal
1/14/2014 11:38:03 PM •
Cagiva...
•
Answered
on Jan 14, 2014
•
84 views
Need circuit diagram for ARLEC 15e 6-24Volt 15Amp Electronic battery charger OR their later model BC58
I can't find a diagram.
The small potentiometer on the control board likely serves as an adjustable component to fine-tune specific parameters. Here are some possibilities:
Voltage Regulation:
The potentiometer might control the output voltage. By adjusting it, you can set the desired charging voltage for different battery types (e.g., 6V or 12V).
Current Limit Adjustment:
It could be used to set the maximum charging current. Adjusting the potentiometer allows you to limit the charging current based on the battery's capacity and condition.
Sensitivity or Threshold:
Some potentiometers act as sensitivity controls. For example, it might adjust the threshold at which the charger switches between charging and maintenance modes.
Setting the Potentiometer:
Without the specific circuit diagram or detailed information about your charger, I recommend the following general steps:
Observe the Potentiometer:
Identify the potentiometer on the control board. Note its position and any markings (if present).
Consult the User Manual:
Check the user manual or operating instructions. It might provide guidance on adjusting the potentiometer.
Trial and Error:
If no specific instructions are available, start with the potentiometer set to its mid-position.
Gradually adjust it while monitoring the charger's behavior (e.g., charging current, voltage).
Observe how the charger responds to changes in the potentiometer setting.
Fine-tune it based on your specific battery type and desired charging characteristics.
Remember that precise adjustments depend on the charger's design and the battery you're charging.
4/18/2024 7:22:52 PM •
Motorcycles
•
Answered
13 hours ago
•
24 views
What is the length of lift cables on a 1993 model 2693 hilo camper and any info on what after market part to use ? thanks
The lift cables on a 1993 model 2693 Hilo camper are 30 feet,2 3/4 inches long and fit the standard height lift of 11 feet 8 inches high to the top of the overhead. The lift uses two cables. According to a Hi- Lo camper travel trailer forum, cable replacement is basically the same on all years and models, with the main difference being the length of the cables from model to model. You can use a cable cut chart to find what cable length you need for your camper, and you'll need to know your year, model name, and box (body) length: Lift cables typically wear out after three to five years, so it's important to replace them as needed and keep them regularly maintained.
4/12/2024 1:26:15 AM •
Motorcycles
•
Answered
on Apr 12, 2024
•
17 views
Not finding what you are looking for?