20 Most Recent 2003 Cagiva Raptor 650 Questions & Answers

Yes All motorcycle chains currently being manufactured use Buna-N (Nitrile) rubber for their o-rings and x-rings and all these manufacturers recommend kerosene as a cleaner. Here's the formulation of WD-40: 80% Stoddard Solvent (that is similar to kerosene) 20% light lubricating oil and a bit of fragrance. Here's the compatibility of Stoddard Solvent with rubbers and plastics: Good Compatibility (OK for both static and dynamic seals) Buna-N (Nitrile) Chemraz Epichlorohydrin Fluorocarbon Fluorosilicone Kalrez Nitrile, hydrogenated Polyacrylate Teflon, virgin Mixed Compatibility (OK for static seals, but not for dynamic seals) Neoprene Vamac Fair Compatibility (OK for some static seals) Polysulfide Polyurethane, millable Poor Compatibility Butyl Ethylene-Propylene Hypalon Natural rubber Silicone Styrene Butadiene Consequently, WD-40 is safe and effective as a chain cleaner and corrosion inhibitor. Link: http://www.efunda.com/designstandard...dard%20Solvent If you clean with a soft brush and WD-40, and plan to follow-up with a chain lube, you can reduce chain lube sling-off if you first remove the oil residue that WD-40 leaves. This residue seems to prevent some chain lube formulations from sticking well to the chain.,,,

Question edited for clarity. A 'carbonator' is a device that adds carbon dioxide gas to liquids like Coca Cola and other sodas to make it fizzy. The word is 'carburetor'. https://www.google.com/search?q=Cagiva+Mito+125.+Carburetor+and+hose+diagram ..

Yes the CDI unit, the sensor that makes it fire or bad wiring connections even to the ignition switch and kill-switch..https://www.google.com/search?q=Cagiva+canyon+500++weak+and+intermittent+sparkI found a Service Manual but it is in Italian!https://www.manualslib.com/manual/1054149/Cagiva-1997-Canyon-500.html#manual..

You have written some conflicting information. How can you know that your engine has no spark if it will not turn over? No problem, please write back and elaborate on its issue, symptoms, engine codes and things you have checked and tested so far. At this point I would start looking around. Inspect the battery and power distribution box. Check that the battery connections are clean and tight. Check that the ground cable, going to the body panel is clean and tight. Check all the fuses for damage (over heating or corrosion) and the same for the relays. Is the antitheft system working (does it recognize your ignition key?)? When you turn the ignition hey to the RUN position. Does the gauge cluster respond like it always does? Do you see the lights come on and go out and can you read the odometer mileage? Please write back and let me know. Good Luck.

Remove the side cover so you can have access to the stator. Then you will be looking for a notch on the inner case. Once you locate the notch you will line up the stator ( which also has a little line or notch on it ) with that notch.

Hello, you need to use manual? If so, the best return to the original car, and you are interested in motorcycle aspects? If you can, you have time to look at.http://www.motorpartstore.com.Good luck and have a nice day

Check the kickstand interlock switch. As deemed mandatory by the DOT.. all street legal motorcycles come with a switch in the kickstand pivot area that detects whether or not it is in the upright (or down) position. This is supposed to prevent riders from taking off with the kickstand down, which can ruin your day when the first left hander comes up- This switch will essentially shutdown the electrics to the engine once you attempt to engage first gear (in the down position)...These switches are fairly reliable but can fail. To test it, take a small jumper wire and connect the two wires (going to the switch) together.