20 Most Recent 2005 Benelli TnT Questions & Answers

Dont do it ... motorcycles are delicately balanced for best operation. Not to mention removing the baffle will annoy those of us who will have to listen to you roar past.

You say "COOLANT LEVEL IS ON THE LOW MARK OR BELOW BUT THERE IS NO ROOM FOR ME TO ADD MORE."
That doesn't make sense - if it is low, there must be room to add more.
I would bleed the whole system - you may have an air block. Pay particular attention to the water pump.

1.Get your supplies ready and expose your engine 2.Unscrew the Oil Filler Cap 3.Remove the Oil Drain Plug 4.Remove and Replace the Crush Washer 5.Clean the Oil Drain Plug 6.Remove the Oil Filter 7.Remove and Clean Plastic Mesh Filter 8.Lubricate the O-ring of the New Filter and Attach it to the Engine 9.Motorcycle Oil Change - Replace Oil Drain Plug & Plastic Mesh Filter Pour Oil 10.Check the Oil Level,,

Put it up on your stand lossen the axel and remove the bolt on the bottom of the shock. Then tighten your chain and lift your swingarm up until its horizontal with the ground, then the chain should have almost no play. Not completely tight, but almost no play. Tighten the axel, and the bolt on the shock, and your set,,,

Yes All motorcycle chains currently being manufactured use Buna-N (Nitrile) rubber for their o-rings and x-rings and all these manufacturers recommend kerosene as a cleaner. Here's the formulation of WD-40: 80% Stoddard Solvent (that is similar to kerosene) 20% light lubricating oil and a bit of fragrance. Here's the compatibility of Stoddard Solvent with rubbers and plastics: Good Compatibility (OK for both static and dynamic seals) Buna-N (Nitrile) Chemraz Epichlorohydrin Fluorocarbon Fluorosilicone Kalrez Nitrile, hydrogenated Polyacrylate Teflon, virgin Mixed Compatibility (OK for static seals, but not for dynamic seals) Neoprene Vamac Fair Compatibility (OK for some static seals) Polysulfide Polyurethane, millable Poor Compatibility Butyl Ethylene-Propylene Hypalon Natural rubber Silicone Styrene Butadiene Consequently, WD-40 is safe and effective as a chain cleaner and corrosion inhibitor. Link: http://www.efunda.com/designstandard...dard%20Solvent If you clean with a soft brush and WD-40, and plan to follow-up with a chain lube, you can reduce chain lube sling-off if you first remove the oil residue that WD-40 leaves. This residue seems to prevent some chain lube formulations from sticking well to the chain.,,,

This simptom is for low battery voltage. I know that you changed the battery but check the voltage from it. If the voltage is somewhere 12.5 - 12.8 V the battery is ok. If not the battery is discharged. Also the amperage is important. If you new battery has less Amps that the producer recommended the bike won't start. I guess for you a battery with minimum 10-12Amps is ok. If the battery seems ok than check also the cables if they are attached properly to the battery. Also you could remove them and clean the contact zone. As a solution for the moment to start the bike is to "donate" some power from a car with some proper cables. Beware at polarity. + with +, - with - . If you put + with - is not good. If the bike's battery is pretty dead than you will need to keep the "donor" car started a few minutes with the cables connected to the car and bike in the same time to allow to the drained battery to charge a little. Please post the result.

The seat lock and key are pretty low security. How to open without a key https://www.google.com/search?q=how+to+open+scooter+seat+without+key New lock and three keys. Also check for a number on the silver face of the lock. Get a key from Benelli https://www.motor-x.com/czesci-do-motocykla,zamki-siedzenia,c,benelli,b.html ..

Try some of the Benelli owners websites as someone might have one or there could be one being sold for spares. Personally I would consider getting a one made as new. There are companies out there that can build exact copies if they have the old one as a template.

Two stroke oil? Page 34 of the manual. The filler is under the seat. when the light comes on, you have 100km left. https://manuall.co.uk/benelli-quattronove-x-scooter/ ..

Try Benelli.com

Hi there I’ve got a Benelli 50cc 2001 model is there a immobiliser on these models

Thread Size: Hex Size: 18mm Buy socket anywhere tools are sold.

Clean, lube and check that all parts are moving.

Run son carb cleaner thru it. If that doesn't work you will need to remove and disassemble the carburator to clean it properly.

Hey Eric, Sounds like fun shooting a quality shotgun such as the M4. but,if you have a question, give us more details.. thanks!!

Sounds like the carb diaphram is ruptured,

between .001" and .0015" at the bottom of the cylinder with no rings fitted to the piston