20 Most Recent 2010 Eton Sport 50 Questions & Answers

and why would you want to do that pray tell

there isn't one if there is a restriction it would prob be in the muffler or pipe and usuallu nothing more than a washer (no not kidding)

what is the correct way to put a new ignition switch on , the pluga dont match , plugs was pulled off and wires are just hanging

if youve never done it DON'T ATTEMPT IT! you'll be sorry! bring it to a competant mechanic and have it done correctly or you'll end up with a bike that will not start or that will run like ****

Does the motor rev-up if the bike is in netrual?

Question edited for clarity. Question moved from MISC to Eton. Wiring Diagram https://www.google.com/search?q=eton+beamer+2+wiring+diagram ..

2-stroke engines can sometimes suffer from a semi-blocked exhaust port or exhaust silencer that saps performance especially if low ash oil isn't used. It is also possible there could be a problem with the reed valve.

Hi ! for an informantion, please visit the website below. If you need more information about a specific electrical issue you can reach me at [email protected]. Motor Part Store Motor Parts Wholesale

try cleaning the carb

1

Unfasten the kickstart by loosening the bolt head of the pin that attaches the kickstart to the outside of your scooter's variator case. This will allow you to pull the pin and remove the kickstart.

2

Remove the outer face of the variator system. On most scooters, this faceplate is attached to the variator case with six bolts.

I can't find a diagram. The small potentiometer on the control board likely serves as an adjustable component to fine-tune specific parameters. Here are some possibilities: Voltage Regulation: The potentiometer might control the output voltage. By adjusting it, you can set the desired charging voltage for different battery types (e.g., 6V or 12V). Current Limit Adjustment: It could be used to set the maximum charging current. Adjusting the potentiometer allows you to limit the charging current based on the battery's capacity and condition. Sensitivity or Threshold: Some potentiometers act as sensitivity controls. For example, it might adjust the threshold at which the charger switches between charging and maintenance modes. Setting the Potentiometer: Without the specific circuit diagram or detailed information about your charger, I recommend the following general steps: Observe the Potentiometer: Identify the potentiometer on the control board. Note its position and any markings (if present). Consult the User Manual: Check the user manual or operating instructions. It might provide guidance on adjusting the potentiometer. Trial and Error: If no specific instructions are available, start with the potentiometer set to its mid-position. Gradually adjust it while monitoring the charger's behavior (e.g., charging current, voltage). Observe how the charger responds to changes in the potentiometer setting. Fine-tune it based on your specific battery type and desired charging characteristics. Remember that precise adjustments depend on the charger's design and the battery you're charging.

The lift cables on a 1993 model 2693 Hilo camper are 30 feet,2 3/4 inches long and fit the standard height lift of 11 feet 8 inches high to the top of the overhead. The lift uses two cables. According to a Hi- Lo camper travel trailer forum, cable replacement is basically the same on all years and models, with the main difference being the length of the cables from model to model. You can use a cable cut chart to find what cable length you need for your camper, and you'll need to know your year, model name, and box (body) length: Lift cables typically wear out after three to five years, so it's important to replace them as needed and keep them regularly maintained.

Check fuel delivery ,or fuel filter

The bike doesn't exist as written. https://www.google.com/search?q=410JS+1000cc+santana We are better with 'year make model 1000cc'. Better to not try and do better than the bike engineers. A mechanical pump runs when the engine is turning, an electric pump will run as soon as the key is turned and create pressure all the time. It would have to be an in tank electric pump or it will burn out. Electric pumps are cooled an lubricated by the fuel passing through it. If it is a carbureted engine, you are pressurizing the carb bowl. If injected, it may already have a fuel return. Check the mechanical pump for a torn diaphragm, they are easy to change. ..

Question edited for clarity and add maker. Try cleaning the Throttle Body. This bike works the same as a car. My first thought was that it has a diaphragm carburetor and the membrane was punctured or split. This bike is not sold in North America https://www.google.com/search?q=yamaha+yzf+r15+v3+clean+throttle+body ..

Question edited for clarity. Usually, there are two ways, you either remove a side cover and it comes out sideways, or you remove the seat and it lifts out. https://www.google.com/search?q=lexmoto+michigan+125+efi+battery+cover+removal https://www.google.com/search?q=lexmoto+michigan+125+efi+manual ..

Question edited for a lot more clarity. Hero Honda Karizma R 0.10 mm on both inlet and exhaust https://www.facebook.com/WonderMechanicAjayKumarSavita/photos/a.1615112108760566/2952364698368627/?type=3 ..