20 Most Recent 2008 Lifan Delta 250 V Twin Questions & Answers

0helpful
1answer

Why my 2008 Lifan 25-B Motorcycle Turn signal stays on and wont blink

I would guess your relay is shot. These are really cheap to replace.
10/13/2014 4:13:40 PM • 2008 Lifan Delta... • Answered on Oct 13, 2014
0helpful
1answer

Is this unit has the same wiring diagram and electronic parts?i have a zongshen 250 vtwin 2003 model

are you fitting the correct pluge some twins run differant plugs in cylinders, have the carbs stripped and cleaned and balanced, clean out the petrol tank and fill with fresh fuel.
1/24/2014 12:10:49 PM • 2008 Lifan Delta... • Answered on Jan 24, 2014
tip

How to adjust carb settings

Hi Charlie.<br />Operations to be performed depends on how much tuning is needed.<br />Carb setting regulates the ratio between air and fuel in the mixture aspired into the cylinders.Optimal air/fuel ratio is usually around 14(air) to 1(fuel). I illustrated the complete job with cleanup and jet replacement and adjustment. In some situation you do not need to perform complete tuning, which involves taking apart the carburetor. In that case perform basic regulation setup using the two adjustment screws at one side of the carb. Adjustment simple procedure starts from part 2/Adjustment. A good approach is first doing adjustment using idle and thickener screws. Then do the whole tune up if the simple adjustment does not work.<br />The complete tuning is based on carburettor cleanup, regulation of main jet and idle jet and needle setup.<br /><br />Part 1 : Complete tuning and cleanup:<br />1. Take apart the carburettor,<br />2. Undo the float chamber(6 in diag) held by screws (26 in diag).<br />3. Clean bowl with with carb cleaner (put a lot of it in the bow, wait a bit and dispose it-finish the job with a cloth if needed) . Clean floats (nr.4) and other parts using carb cleaner and cloth.<br />4. Use a flat screwdriver to remove the main jet screw (placed in the chamber, held by big golden screw, goes between the floats). Spray the main jet. You must be able to see through it.<br />5. Use the carb cleaner to clean the accelerating pump and all the other parts inside the part. Needle and small parts must be cleaned. Clean the idle jet, which is the smaller golden screws. If you have a compressor blow into the jets (you can blow them even without compressor, but follow H&S).<br />6. If possible replace main and idle jets. Sometimes you may like to replace the jet with a bigger one to get a richer mixture.<br />7. Adjust the needle if needed. A lower needle settings means a richer mixture.<br />8. Remove idle adjustment screw (7) and main adjustment screw(31), clean them screw them back in without tightening and perform part 2. Leave the screws about one and half turn from all way in.<br /><br />Part 2: Tuning and minor cleanup - Here you mainly operate on idle and air (thickener) adjustment screws (8 and 12 in diag)- Start from here, if this does not work, do part one:<br /><br />1) If the engine runs start from idle adjustment: screw or unscrew the idle regulator to adjust the idle speed, the screw is placed to one side of the carburetor and has a spring (part 12).<br />Keep idle least slightly higher than the minimum needed. Example, if the engine stays on slightly below 1000 rpm, set idle to a bit higher with engine revving above 1000 rpm.<br /><br />2) The thickener, placed near that of the minimum screw regulates the air flow. Tighten the screw and unscrew 2 turns from all the way in. Do regulation from this position. <br /><br />Here carburetor diagram and part list. The diagram is taken from service manual. The manual for Lifan 150 (does not include carb setting) has been uploaded here:<br /><br />http://www.mediafire.com/?o3r8x2ujrdbfb6o
0helpful
1answer

I have a lifan 250cc

I've found a Yamaha XV250 manual online (Yamaha-XV250-Shop-Manual). Doubtless there are others out there.

The good news is that most of it looks like it'll apply to the Lifan (without test yet). Other details could be interchanging and visit this Lifan Forum.

Good luck.
9/23/2011 5:47:25 PM • Lifan Comet 250... • Answered on Sep 23, 2011
0helpful
1answer

Can I get a service manual for 2022 LIFAN-LYCAN-250cc

Question edited for typos. Question moved from Cars and Trucks No Service Manuals, only Owner Manuals. Those are easy basic tasks as long as you can find the parts. https://www.google.com/search?q=Pandigital+frame+display%2C+connect+to+iMac Parts https://www.google.com/search?q=lifan-lycan-250cc+parts+list ..
1/17/2023 2:42:06 AM • Lifan... • Answered on Jan 17, 2023
0helpful
2answers

I need a fuel line schematic for a lifan LF250-CC cruiser 2005

Hi, You can call the manufacturer of the bike and ask them email you the schematic in order to get it as quickly as possible. There phone number should be in the bike manual's first few pages. Thank you.
11/10/2022 6:20:15 PM • Lifan... • Answered on Nov 10, 2022
0helpful
2answers

HOW to set timing on lifan 200cc

The CDI timing is locked in by the key in the flywheel (or so I just read). The valve setting is as such: how do you set timing on a lifan 200cc trail bike? the bike does not have a timing chain it have pushrod how do set the timing do any one know

1 Answer

Favorite Answer Set the piston at top dead center (TDC), position the cam so that both valves are closed then assemble. That engine is based on a Honda engine. The Honda has an overhead cam that is driven by a cam chain. The cam drives rocker arms that open the valves. So your statement about push rods sounds fishy.
7/2/2022 11:13:50 AM • Lifan... • Answered on Jul 02, 2022
0helpful
1answer

Lifan 200cc 163 fml repair manual

Request the manual from Lifan.
10/29/2020 3:46:35 AM • Lifan... • Answered on Oct 29, 2020
0helpful
1answer

WERE CAN I GET AN EXHAUST FOR A 2015 LIFAN 50QT 26A REG NUMBER AF65 CCJ

Contact a Lifan main dealer!
5/19/2020 12:29:31 PM • Lifan... • Answered on May 19, 2020
0helpful
1answer

Will not turn over 2006 Lifan 250

Did you test starter under a load or just a bench test because it will always work if not under a load
9/9/2019 5:51:40 AM • Lifan... • Answered on Sep 09, 2019
0helpful
1answer

I need a turn signal switch for my 2004 lifan moped 50cc it's a male plug nine wires with two single wires coming off the bundle can't find one

fixya doesnt sell products try a motorcycle shop or online search
5/10/2019 12:39:29 PM • Lifan... • Answered on May 10, 2019
0helpful
1answer

125cc lifan king Does it have a govenor

No. However it most likely has a rev-limiter to prevent overrevving/damage.
4/2/2018 6:07:34 PM • Lifan... • Answered on Apr 02, 2018
0helpful
1answer
0helpful
1answer

I Need a manual for a Lifan 250V

of course!!!If you buy a motorcycle, need in motorcycle accessories, you can refer to the below website. http://www.motorpartstore.com.Good luck and have a nice day
4/11/2016 8:27:47 AM • Lifan... • Answered on Apr 11, 2016
0helpful
1answer
0helpful
1answer

Downloadable manuals

Better finding the original bike that Lifan knockedoff Like Yamaha 250
4/10/2015 3:59:02 PM • Lifan... • Answered on Apr 10, 2015
0helpful
1answer

Hi I own a 2011 lifan lf400 thunder and we can't get a starter to put in it is there anything that may fit??

you should be able to get your old one rebuilt or get a rebuild kit and do it yourself
3/31/2015 4:19:12 AM • Lifan... • Answered on Mar 31, 2015
Not finding what you are looking for?
2008 Lifan Delta 250 V Twin Logo

5 questions posted

Ask a Question

Usually answered in minutes!

Top Lifan Experts

Marvin
Marvin

Level 3 Expert

85241 Answers

john h

Level 3 Expert

28478 Answers

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

55442 Answers

Are you a Lifan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Comet 250 EFI Lifan

  • Comet 250 EFI Lifan

Most Popular Question

2008 lifan 25 b motorcycle turn signal

  • Motorcycles
Loading...