20 Most Recent 2008 Kymco Agility 50 Questions & Answers


Hi, Anonymous for more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://www.kymcoforum.com/index.php?topic=10603.0
How to start scooter without keys
KYMCO AGILITY 125 Service Manual
Genuine Kymco spare parts
Kymco Agility 125 Driver Manual

2008 Kymco... | Answered on Aug 03, 2019


Hi, Graham_mcvea and the usual suspects are:
1. Fuel tank empty.
2. The fuel tank has old dead gas.
3. Fuel tank bottom contaminated with ethanol sludge, dirt, water, rust, etc.
4. Fuel supply valve/petcock turned off.
5. Fouled spark plugs.
6. Engine flooded as a result of overuse of the choke.
7. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
8. Fuel valve/petcock or filter clogged.
9. Fuel line to carburetor or throttle body pinched, kinked or blocked.
10. Carburetor float stuck.
11. Fuel injectors clogged.
12. Fuel injectors stuck open.
13. Quick disconnect check ball stuck.
14. Compression below 75 PSI.
15. A stuck-bent-burnt valve.
16. Improper valve clearance (too tight)
17. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a cursory reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
18. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
19. Loose or corroded wire connection at the coil or plug between ignition sensor and ECM module.
20. Spark plug cables in bad condition and shorting check for spark leakage in the dark, cable connections are loose or connected to the wrong cylinders.
21. Ignition timing incorrect due to a faulty ignition coil, ignition module or MAP, CMP, CKP, O2, TPS, ETP, IAC sensors.
22. Faulty neutral, clutch, kickstand safety switch.
23. Faulty fuel pump or fuse or relay.
24. Faulty or corroded run/stop switch.
25. Tilt sensor needs a reset.
26. Security system not disarming alarm needs a reset.
27. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Scooter Troubleshooting Scooter won start All about Scooters
https://www.youtube.com/watch?v=lRJsuOzk_vs
KYMCO AGILITY 125 Service Manual
Kymco Scooter Parts ATVs Scooter Parts Performance Scooter Parts...
Kymco Agility 125 Driver Manual

2008 Kymco... | Answered on Jul 13, 2019


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kymco, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?q=Wiring+diagram+2008+Kymco+Agility+50&tbm=isch&source=univ&sa=X&ved=2ahUKEwjGvYOQ7arjAhXwtlkKHa84DLsQsAR6BAgFEAE&biw=1440&bih=757
http://www.kymcoforum.com/index.php?topic=12794.0
KYMCO AGILITY 125 Service Manual
http://kymcopartsonline.com/catalog/table_overview.php?s_fk_manufacturers_id=21&s_fk_model_ye
Kymco Agility 125 Driver Manual

2008 Kymco... | Answered on Jul 10, 2019


Hi, Dqforme14 and the usual suspects are:
1. Throttle cables not properly adjusted.
2. Idle screw adjusted too low.
3. Air-fuel mixture screws not properly adjusted.
4. Pilot jet clogged.
5. Pilot jets too small.
6. Clogged air filter.
7. Faulty choke.
8. Multi carburetors not in sync.
9. Carburetor float needle valve stuck.
10. Fuel not getting to the carburetor.
11. Slide stuck in the carburetor.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.scootershack.co.uk/threads/kymco-agility-50-dont-laugh-running-issues.4914
http://www.scootdawg.net/showthread.php?t=54682
KYMCO AGILITY 125 Service Manual
http://kymcopartsonline.com/catalog/table_overview.php?s_fk_manufacturers_id=21&s_fk_model_ye
Kymco Agility 125 Driver Manual

2008 Kymco... | Answered on Jul 10, 2019


Hi, Robbeckrich for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kymco, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?q=Fuel+line+routing+2008+Kymco+Agility+50&tbm=isch&source=univ&sa=X&ved=2ahUKEwiXisOB66rjAhWupFkKHbDWCtQQsAR6BAgGEAE&biw=1440&bih=757
GY6 Scooter Fuel and Vacuum system hands on
KYMCO AGILITY 125 Service Manual
http://kymcopartsonline.com/catalog/table_overview.php?s_fk_manufacturers_id=21&s_fk_model_ye
Kymco Agility 125 Driver Manual

2008 Kymco... | Answered on Jul 10, 2019


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kymco, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.manualslib.com/manual/1050371/Kymco-Agility-Rs-50.html?page=11
https://www.google.com/search?q=Head+bolt+torque+spec+Kymco+Agility+50&source=lnms&tbm=isch&sa=X&ved=0ahUKEwivwpGz3KrjAhXqx1kKHZxOBZ8Q_AUIECgB&biw=1440&bih=757
KYMCO AGILITY 125 Service Manual
http://kymcopartsonline.com/catalog/table_overview.php?s_fk_manufacturers_id=21&s_fk_model_ye
Kymco Agility 125 Driver Manual

2008 Kymco... | Answered on Jul 10, 2019


Hi, Anonymous before testing any electrical component in the Starting Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Engine Run Switch is "FAULTY" or corroded.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
5. Bank angle sensor needs a reset or is faulty.
6. FOB battery low or dead.
7. Faulty ignition switch.
8. Faulty starter button.
9. Faulty kickstand, clutch, neutral safety switch.
10. Security alarm needs a reset.
11. Starter relay, solenoid, starter motor or circuit wiring faulty.
12. Starter armature or field coils have failed.
13. Main fuse or circuit breaker may be blown or faulty.
14. Faulty ignition relay.
15. The electric starter is working but starter clutch has failed.
16. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Scooter Troubleshooting Scooter won start All about Scooters
https://www.killermotorsports.com/scooter-power-no-start
KYMCO AGILITY 125 Service Manual
http://kymcopartsonline.com/catalog/table_overview.php?s_fk_manufacturers_id=21&s_fk_model_ye
Kymco Agility 125 Driver Manual

2008 Kymco... | Answered on Jul 10, 2019


Hi, Lucindadocka moisture, condensation, rain, or bike washing can make the bike run sluggish, not able to rev, and misfire. Older bikes, engine configuration, and exposed electrical components are at the front of the line for acting up. During the diagnostic procedure spray Electrical Contact Cleaner on corroded wire connectors/pins/sockets etc. and apply a liberal amount of "DIELECTRIC" grease to the mating harness/wire connectors. WD40 works great for eliminating suspect areas in your quest to find the real offending gremlin.
For additional insurance you can spray a High Temp Clear Coat on the most vulnerable areas it will work like Scotch Guard does on fabric. Fabricate a rubber or plastic splash guard to deflect water coming off the front wheel getting to the front cylinder spark plugs. The design should be adequate for its purpose with the least amount of airflow restriction to cool the cylinders. The usual suspects are:
1. Air filter soaked with water.
2. Water in the fuel system gas tank and carburetors.
3. Wet ignition coil packs.
4. Spark plug boots wore out or loose allowing water to enter.
5. Spark plug cables old and cracked check for spark leakage in the dark.
6. Spark plug wells filled up and drain holes clogged.
7. Water in a wire harness that has exposed open ends and have a sharp bend or crimp allowing the liquid to form its own pool of potential threats to chaffed wiring.
8. Sensitive fuel tuners and downloaded ECM remaps may get confused with the abnormal cylinder temperature difference in a V-4 engine configuration.
9. Fuel injected bikes need to have the electrical connectors removed and sprayed with contact cleaner then blown dry and checked for continuity with a test light or multimeter, then treated with Dielectric Grease.
If your bike will not run right or even start after going through the checklist, despair not, letting it sit for a couple of days in a warm environment is like an eviction notice for the Gremlins and then your bike will be back to its old self. You can speed up this process by using forced air to dry out electrical connections.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Scooter Troubleshooting Scooter won start All about Scooters
https://www.reddit.com/r/scooters/comments/320o0k/kymco_agility_50_wont_start_after_rain
KYMCO AGILITY 125 Service Manual
http://kymcopartsonline.com/catalog/table_overview.php?s_fk_manufacturers_id=21&s_fk_model_ye
Kymco Agility 125 Driver Manual

2008 Kymco... | Answered on Jul 10, 2019


Hi, Anonymous and the usual suspects are:
1. Dirty or clogged air filter.
2. Faulty spark plug.
3. Bad Gas.
4. Improper oil level.
5. Improper chain adjustment and lubrication.
6. Low tire pressure.
7. Dirty or contaminated carburetor needs cleaning and tuning.
8. Clogged or faulty fuel pump or injectors.
9. Improper valve adjustment.
10. Slipping clutch.
11. Improper timing.
12. Low compression.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://www.kymcoforum.com/index.php?topic=611.0
https://www.bikechatforums.com/viewtopic.php?t=214872
https://www.youtube.com/watch?v=vLSozrNWzAw
KYMCO AGILITY 125 Service Manual
Kymco Scooter Parts ATVs Scooter Parts Performance Scooter Parts...
Kymco Agility 125 Driver Manual

2008 Kymco... | Answered on Jun 28, 2019


Hi, Luis before diagnosing any turn signal/running light/parking light issue make sure the bulb is good and the light fuse has continuity with a test light. If you have replaced you OEM lights with LED lights you are going to need a load equalizer. If no turn signals work the cause could be a faulty turn signal module or the connector going to it, look for corroded, loose, or broken pins/sockets. Contact spray cleaner is great for removing corrosion. If your speedometer does not function properly it will have to be fixed first because your turn signal module gets the data from the speedometer for normal turn signal function. If your front turn signals don't work use a test light to check for power and ground at the bulb socket, then start backtracking the wiring through every wire connector to the turn signal switch/button and check for continuity, go all the way back to the fuse if necessary to find the cause of the malfunction. If your rear turn signals don't work check your rear fender wiring harness connector first for corroded, broken, loose pins/sockets, power, and a good ground, (the harness connector is usually located under the seat on the front of the rear fender) then keep tracing the wiring look for obvious harness damage caused by the rear tire. If you still can't find the malfunction backtrack from the rear fender wiring harness connector. If one side does not work you could have a faulty turn signal switch or module check for continuity. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Turn Signal Troubleshooting Scooter Doc Forum
Fix scooter that does not have working turn signals
http://www.49ccscoot.com/manuals/Kymco_Agility_50_Service_Manual.pdf
Kymco Spare Parts
http://www.kymcousa.com/owners/onroad/Agility50-125.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


2008 Kymco... | Answered on Jan 20, 2017


if its a 2stroke engine then 50psi isnt enough !?? 100psi min on any make of engine !!

2008 Kymco... | Answered on Jun 02, 2014


some bikes/scooters are fitted with safety device an engine cut off when on the side stand, look at the side stand the may be what looks like a pin on it and when the stand is down the pin will be pushed in. if it stalls on the main stand i had a friend who's bike had a safety feature of which it wouldn't start with the back wheel in the air. depends on which stand it happens

2008 Kymco... | Answered on Feb 20, 2013


Same with mine nothing works have you found a solution yet ?

2008 Kymco... | Answered on Oct 30, 2011


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kymco, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
KYMCO SCOOTER 50CC OIL CHANGE SPARK PLUG FUEL
Spark plug location on 150 and 50cc scooter
Manuals Kymco
http://kymcopartsonline.com/catalog/table_overview.php?s_fk_manufacturers_id=21&s_fk_model_ye
https://www.manualslib.com/manual/965525/Kymco-Visa-R-110.html

Kymco Partner... | Answered on Jul 10, 2019


Hi, Anonymous before testing any electrical component in the Starting Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Engine Run Switch is "FAULTY" or corroded.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
5. Bank angle sensor needs a reset or is faulty.
6. FOB battery low or dead.
7. Faulty ignition switch.
8. Faulty starter button.
9. Faulty kickstand, clutch, neutral safety switch.
10. Security alarm needs a reset.
11. Starter relay, solenoid, starter motor or circuit wiring faulty.
12. Starter armature or field coils have failed.
13. Main fuse or circuit breaker may be blown or faulty.
14. Faulty ignition relay.
15. The electric starter is working but starter clutch has failed.
16. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.ktmatvhq.com/forum/xc-body-control-protection/8807-quad-wont-start-there-no-power-all.html
Ignition turned on but no power at all Bike just stop working
Manuals Kymco
http://kymcopartsonline.com/catalog/table_overview.php?s_fk_manufacturers_id=21&s_fk_model_ye
Owner Manuals KYMCO

Kymco Partner... | Answered on Jul 10, 2019


if this is a maintenance free battery then I am not surprised. Mine showed full charge but didn't start the bike. Get a new battery its probably shot.

Kymco Partner... | Answered on Apr 07, 2014


Check the fuses

Online Owners manual and Service manual

https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&sxsrf=ALeKk00ZH8nUnIjb8VpOzUSK9jMOU31hSg%3A1586979323433&ei=-2GXXuyBGoO-tQb00ICICg&q=2009+Kymco+UXV+500i+fuse

Kymco... | Answered on May 03, 2020


Hi, Dan the answer to this question is way above my pay grade for this situation, I would call or visit my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts enquiry.
Good luck and have a wonderful day.

Kymco... | Answered on Mar 18, 2020


Hi, Jim the answer to this question is way above my pay grade for this situation, I would call or visit my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts enquiry.
Good luck and have a wonderful day.

Kymco... | Answered on Mar 18, 2020


Hi, Raymond you need to repost your question under the ATV category, not Motorcycles. Thanks, Gregg

Kymco... | Answered on Jan 25, 2020

Not finding what you are looking for?
2008 Kymco Agility 50 Logo

24 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

2006 Kymco Agility 50
2006 Kymco Agility 50

-5 Questions

2007 Kymco Agility 50
2007 Kymco Agility 50

-11 Questions

Top Kymco Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6347 Answers

Are you a Kymco Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Partner 110 Kymco

  • Partner 110 Kymco

Most Popular Question

hot wire kymco aglity 50

  • Motorcycles
Loading...