20 Most Recent 2007 Suzuki RMZ 450 Questions & Answers


the valve clearance may be too tight

2007 Suzuki RMZ... | Answered on Apr 02, 2018


not for sure,but look on the frame right side almost under the frame,about mid way of the engine.

2007 Suzuki RMZ... | Answered on Jun 12, 2014


The seal in the water pump has gone bad and is letting water get into the oil. The oil turns grey when water gets emulsified with the oil. The pump will need a new seal, "O" ring and gaskets. Go to this website to see an exploded view of the pump assembly; www.babbittsonline.com tombones49_289.gif

Suzuki XTC 125... | Answered on Sep 11, 2011


Contact Suzuki to request it.

Suzuki... | Answered on Jan 09, 2021


Order the service manual from Suzuki.

Suzuki... | Answered on Jan 08, 2021


Request the diagram from Suzuki.

Suzuki... | Answered on Jan 08, 2021


Test the bulb with two wires to the battery.

Check the grounds.

Check the switch.

Then clutching at straws, the continuity of all the wires involved. They often break inside the insulation where the wire flexes from headlight unit/forks to the frame.

Suzuki... | Answered on Dec 24, 2020


If it has an identicle part number, yes. Otherwise no it won't work correctly, if at all.

Suzuki... | Answered on Dec 10, 2020


take apart. have ultrasonic cleaning done to all parts, add rebuild kits with new jets and then bench synch them, install back on bike and synch them with a good gauge set

Suzuki... | Answered on Dec 08, 2020


Step 1 Pull back the rubber cover of the clutch lever to reveal the lock nut and adjusting screw. Loosen the lock nut with a wrench. Tighten the adjuster screw until it won't turn any more.
Step 2 Remove the left frame cover of the body of the bike and set it aside in a safe place. Remove the bolts holding the secondary gear case cover and the clutch release cover with a socket wrench. Remove the secondary gear case and clutch release cover and set them aside.
Step 3 Find the lock nut and screw located at the lower end of the clutch assembly cable. Loosen the lock nut. Loosen the screw by three rotations. Slowly finger tighten the adjusting screw until you start to feel resistance. Loosen the screw a quarter-rotation. Tighten the lock nut to hold it in place.
Step 4 Locate the lower cable adjuster above the clutch release cover. Loosen the two lock nuts of the adjuster with the socket wrench. Turn the cable adjuster screw and check the clutch lever as you turn. Tighten the adjuster screw until the clutch lever will wiggle loosely or "play" about 1/8-inch. Tighten the lock nuts.
Tighten the lock nut of the clutch lever. Replace the clutch release, secondary gear case and left frame cover. Pull the rubber cover back over the clutch lever.

Suzuki... | Answered on Nov 20, 2020


Request the information from Suzuki.

Suzuki... | Answered on Nov 20, 2020


There should be an adjustment on the carburetor. If you follow the throttle cable to the carburetor, and turn the throttle, you will see what moves on the carburetor when opening the throttle. Whatever part moves, there should be a screw or knob that you can adjust to raise or lower the idle.

Suzuki... | Answered on Nov 16, 2020

Not finding what you are looking for?
2007 Suzuki RMZ 450 Logo

Popular Tags

11 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Suzuki Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6528 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

217 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

XTC 125 Suzuki

  • XTC 125 Suzuki

Most Popular Question

need help timing

  • Motorcycles
Loading...