20 Most Recent 2007 Suzuki Boulevard S50 Questions & Answers


Go to Ebay and check to see what completed sales have been going for.

2007 Suzuki... | Answered on Jan 10, 2017


You normally do not grease brakes. The only time use use special brake grease, is when you are taking the pistons out to rebuilt the hydraulic seals. They it helps to use special brake grease to aid in reassembly, and to prevent water getting in past the dust cover.

You bleed all brakes the same.
First you top up reservoir.
Then pump pressure.
Then open the furthest breeder first, until pressure drops.
Repeat until clean and no bubbles.
Refill as you go.

2007 Suzuki... | Answered on Jun 25, 2011


theres a cross pattern in the dipstick you dont want to go past the top of the pattern depending on the size of the motor should be less then a liter

Suzuki Boulevard... | Answered on Aug 28, 2016


It is a screw on the carburetor; IN = lean, OUT = rich mixture.

Suzuki Boulevard... | Answered on Jun 25, 2015


The starter button is supposed to turn off the lights during the start. The new solenoid means that is OK. That means the starter is the problem. Tap on the starter with a plastic hammer, back of a screwdriver, etc., if the starter works now you just need new starter brushes. If the armature is shorted, the end cap bearings worn, the magnets broken, etc. then you will need to replace the starter assembly. Only the brushes are available as spare parts to fix the starter.

Suzuki Boulevard... | Answered on Apr 17, 2013


Backfiring with flames usually means 2 things1) Rich mixture (lots of fuel). The spark plugs becomes black powdered. Need good carburetor setup (main jet, needle, pilot screw adjustments)2) Poor valve sealing. Damaged valve seats causes that. Need to take apart the cylinder head and grind the valves (procedure that all mechanics know). That means that when the mixture is compressed inside the chamber and ignited part of the mixture explosion escapes from the leaking valve's seat to the exhaust, so concentrated unburnt fuel in the exhaust catches fire and explodes through the exhaust, creating the flame.

Suzuki Boulevard... | Answered on Feb 07, 2012


It will need to be remove to replace the grips, Be sure to use a quality #3 phillips screwdriver.

Suzuki Boulevard... | Answered on Apr 29, 2011


do you mean the floats? if so then take the carb apart again and inside the bottom half you will see 2 pieces of plastic on a spring number 22 on pic when you blow through the petrol intake pipe air will escape from near the floats when you lift them up the air will shut of which is what will happen when the carb is full of petrol if the air dosnt shut of the floats need adjusting bend the spring carefully upwards ( I DO MEAN CAREFULLY) then try again you may have to do this a few times untill you get it right

i would check the needle height first unscrew the throttle cable fromt the top of the carb watch out for the spring and you will see the needle inside the sleeve number 8 on the pic
the needle is number 7 remove the plastic washer from the bottom and pull the needle up a bit you willl see notches on the side of the needle just slide the washer down the side untill it clips into the one you want that will reduce the amount of petrol going into the carb


1stdcarb.jpg hope this helps


John

Suzuki Boulevard... | Answered on Apr 09, 2011


Try to avoid removing them. Most Carb problems are caused by water. Look for a drain plug in the carb bowls, remove the plug and flush the carbs with methylated spirits via the fuel pipe hose. Remove the air cleaner box to gain access. Check there is no water in the tank by draining fuel into a glass jar, water and fuel dont mix you will see if any is evident. A small amount of metho added to the tank will dilute water to help it pass through the system. After flushing and before replacing air cleaner bow, start the motor and raise the RPM, then block the mouth of each carby in turn to use the engine vaccuum to '**** through' any small debris. Before replacing air cleaner box study the way the carbs are mounted in case you have to remove them. Remove carbs as complete as possible and clean the bowls and jets from underneath, try not to disturbe the adjustments as a full tune up will be necessary if they are not in sync. Carbs are often dismantled only to find the problem is electrical which is way more common.
I hope this helps you

Suzuki Boulevard... | Answered on Mar 16, 2011


Check your oil level see if it is at the correct level,check it with the bike upright and level. Overfilled crankcase the oil has nowhere to go but out the breather connection to the air box.

Suzuki Boulevard... | Answered on Jan 08, 2011


Okay this isn't fare you didn't tell me what Suzuki Motorcycle but from what you did say about the oil in the air box I'm going to assume it's a V Twin cruiser type. I'll also assume you do a bunch of short hops and "cruising the strip" low reves putting along looking good. If I'm right with this assumption then I'm going to assume again that you have the rings stuck to the lands in the piston and you are getting some pressure build up in the crankcase, couple this with hot oil and you get a super fine oil mist which is sucked into the breather box. Stick your finger in the exhaust pipe and rub it against the side, if it comes out dirty with black dry carbon your are right it isn't coming out the pipe But if it's wet oily then you haven't been looking behind you (which is a good thing) when you are riding. and the oil is going out the pipe as well. If you have a ton of miles on it then it's a good time to have the top end rebuilt including pulling the barrels and clean up those pistons hone up the cylinders and install a new set of rings. Of course this is all an assumption that you have a V twin cruiser.

Suzuki Boulevard... | Answered on Jan 07, 2011


Follow the choke cable down to the intake and see where the bracket is holding it, make sure it is adjusted correctly so when off there is no play. See if there is a spring on the choke, if there is you might need to remove it or get a less tight one, it has probably been swapped out at some stage. If removing the spring check you can manually return the choke before riding, if it can't be returned manually then replace the spring. You possible need a new choke cable

Suzuki Boulevard... | Answered on Feb 19, 2010


THE JETS ARE CLOGGED IF ONE CARB IS GETTING GAS SO SHOULD THE OTHER

Suzuki Boulevard... | Answered on Jan 31, 2010

Not finding what you are looking for?
2007 Suzuki Boulevard S50 Logo

Popular Tags

8 questions posted

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6480 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

217 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Boulevard S50 Suzuki

  • Boulevard S50 Suzuki

Most Popular Question

need know much bike price 2007 suzuki

  • Motorcycles
Loading...