Top 20 2005 Honda Shadow Spirit 750 Questions & Answers

Hold your clutch in, push down on your clutch pedal till your down to the last gear slightly and barely push up half way on your gear pedal and presto!

Hi! if you don't have a hammer-screwdriver (what is the right name?) just use a puncher + hammer: on the side of the head first punch a small hole, so the tip of the puncher is well held on that spot/hole. Then carry on with the puncher a bit off-axis (of the screw), to cause the screw to rotate a bit to the left. Then carry on. Some WD40 can help too. I got some great results like that. Good luck!

hi ..make sure that you have enough voltage output of your charger..If your battery is 12volts your charger must have a higher voltage out to complete the charging ..or maybe your battery is dead..long time storage of a battery can cause the battery damage ..that's all thank you

I think it might be the idle SPEED adjustment, that adjusts the speed of the engine at idle RPMs. It should adjust both carbs by the one knob, as it adjusts through the linkage.

start it and shut the fuel petcock so it will drain the bowl of the carburator.It sounds like it has a sticky float valve to me... and this will solve that .hopefully.

just follow the hot side battery cable and it should lead you to the starter. hope that helps you.

try looking here
www.bikebandit.com

We need to know what model, size and year of the bike. Most street bikes use 10 oil. Move the weight up 5 units if you weigh over 225 lbs. Again, let me know the model, size and year.

The Power Steering has failed. There has been a factory recall for a suddenly failing electrical steering shaft, that could cause the rider to loose control. This does not have to be your problem but anyhow either the electronics or the pump failed. Error codes or messages usually have to be erased by a simple reset procedure or disconnecting a plug, after repairs are done.

Question edited for clarity, but no idea what you mean by - "What do I need to do to get the gay? The clutching gauge in again?" You issue is probably that all the clutch plates are glued together. Leaving a bike for 21 years will do that. https://www.google.com/search?q=1985+Honda+Gold+Wing+1200+stuck+clutch ..

Check the wiring, especially the engine earth lead.

Question edited for clarity and add magic word. The Owner's Manual covers basic repairs and is free. https://www.google.com/search?q=honda+anf125+innova+service+and+repair+manual

Honda ANF125 Innova Service and Repair Manual

Google Books https://books.google.com > ... > Repair & Maintenance The aim of this manual is to help readers get the best from their motorcycle. It provides information on routine maintenance and servicing and the tasks are ...

Honda ANF125 Manuals

ManualsLib https://www.manualslib.com > ... > Scooter Manuals and User Guides for Honda ANF125. We have 1 Honda ANF125 manual available for free PDF download: Owner's Manual ...

Honda Scooter ANF125 Innova Scooter (2003 - 2012)

Haynes Manuals https://haynes.com > en-gb > anf125-innova-scooter Detailed repair guides and DIY insights for 2003-2012 Honda Scooter ANF125 Innova Scooter's maintenance with a Haynes manual. ..

Question edited for clarity. The RC26 has a few modifications, but nothing that should alter the wiring.

1986-1987 - VFR700F / VFR700F2 (RC26)

The "Tariff Buster"[ 700cc VFR700F was almost identical to the 750cc version, with minor changes to graphics (no 750 on the lower fairing), shorter stroke, different cams, and altered ignition timing. Otherwise the VFR700F2 was mechanically the same as the standard F, but had an upgraded rear shock and fork internals alongside square gauges. Wiring diagrams and manuals https://www.google.com/search?q=1987+honda+vfr+700f+wiring+diagram ..

For a 1999 Honda CBR929RR, the cylinder head bolt torque specifications are essential to ensure proper engine assembly and function. When tightening the cylinder head bolts, it's crucial to follow the manufacturer's recommended torque settings to prevent damage to the engine components. For the CBR929RR, the cylinder head bolt torque specifications are typically as follows: 1. **Initial Torque:** 29 Nm (2.9 kgf-m, 22 ft-lbs) 2. **Final Torque:** 64 Nm (6.4 kgf-m, 47 ft-lbs) It's essential to tighten the cylinder head bolts in the specified sequence and in multiple stages, gradually increasing the torque until reaching the final specified torque. The exact tightening sequence can usually be found in the service manual specific to your motorcycle model. When torquing the head bolts, ensure you're using a reliable torque wrench calibrated in the appropriate units (Nm or ft-lbs). Always follow the tightening sequence precisely to ensure even pressure distribution across the cylinder head gasket. Additionally, it's advisable to use new cylinder head bolts if the old ones have been previously tightened or stretched beyond their yield point. This helps maintain proper clamping force and ensures the integrity of the engine assembly. As always, referring to the service manual or consulting a professional mechanic experienced with motorcycle engine assembly can provide additional guidance and ensure the correct torque settings are applied during the cylinder head installation process.

found this on eBay copy and paste Picture 1 of 1 Vesrah Oil Filter for Honda VT250C V Twin Magna 1994-1995

. One possibility is that the spark plug or plug wire is faulty 1. Another possibility is that the carburetor needs cleaning and adjustment It could also be due to a valve adjustment issue or a bent rod. I would recommend taking your motorcycle to a professional mechanic who can diagnose and fix the issue. If you prefer to troubleshoot it yourself, you can start by checking the spark plug and plug wire for any damage or wear and cleaning the carburetor. However, please note that working on a motorcycle engine can be dangerous and requires specialized knowledge and tools. Please take all necessary safety precautions and follow the manufacturer's instructions when working on your motorcycle.

The problem might be with the air filter, and if not there are a few other things that could be causing your Shadow engine to bog down on acceleration. This includes a dirty carburetor, carb adjustment issues, or other internal problems like damaged vacuum lines or a cracked manifold

Question edited for clarity. Question moved from Honda Cars. I haven't seen one of those for 40 years! The Braided cable goes to battery negative - They normally have a Red Cable to the battery Positive + And if I recall, there is an inline fuse in the positive? Here is the cable https://www.ebay.com/itm/NOS-OEM-Honda-Cub-50-70-C70-K1-C50-C65-M-CA102-C102-Cable-Earth-Battery-Ground-/172214475304?_ul=IN and here https://www.ebay.com/itm/225016392400 Service manuals x two :>D

Honda C102 Service manual

Honda 4-stroke.net https://4-stroke.net > honda-c102 > downloads > 440-... You can go to our downloads and grab yourself a copy! Download the Honda C102 Service Manual in the following format: pdf Service manual for Honda C102 (1.93 MB).

• Workshop manual for Honda C102 (1961)

  https://4-stroke.net > honda-c102 > downloads You can go to our downloads and grab yourself a copy! Download the Honda C102 Service Manual in the following format: pdf Service manual for Honda C102 (1.93 MB).

Service Repair Manual Honda C100, C102, C50,C70, C90

Blogger http://myhondac100.blogspot.com > 2013/10 > servic... Oct 21, 2013 - Service Repair Manual Honda C100, C102, C50,C70, C90. http://www.servicerepairmanualonline.com/4449/honda-super-cub-50-c50- ...

ck out this site about 11 posts down.. https://www.advrider.com/f/threads/honda-deauville-nt700v-discussion-thread.503073/page-60

Your description sounds likely an exhaust valve is leaking.