20 Most Recent
2007 Kymco Venox 250 Questions & Answers
Does anybody know where I can get a head cylinder for a 2007 kymco venox 250cc
Try eBay or a motorcycle part finder site
And on the problem of it reoccurring difficult to say as need to know what damage was caused to piston and valves
Was it just one rocker arm that broke or is the other damaged did the timing jump and piston hit open valves driving them up and breaking arm and damaging cam shaft lobes
You really need to find out why and how it happened
As it may require a complete timing system replacement on that cylinder cam shafts , rocker arms , valves ,drive sprockets top and bottom , drive chain and a piston
How can I tell if "I" have a blown head gasket?
Find exactly where the fluid is leaking. It could be simply a fractured line. Is your oil okay? If not diluted with coolant then unlikely to be the head gasket. Not down on performance? Again unlikely it is the gasket.
Wont Start
There is one sparkplug at center front of engine and one at center rear. They are fairly easy to change. Just follow your spark plug wires.
Did the vehicle set up for a long period and did you use a fuel stabilizer in the fuel.
Hi, big bore high cc
Can you be more descript with details? There is enough room to add a lot of details so we can provide assistance. I apologize for not understanding your question.
Hola, Big Bore 250cc Kymco
el differencia en 250//350 es el distancia la piston movamiento ,pero mas grande motors son diferente pero tu queires sabe yo no say .endonces para montacie una motor 250/350 niguno problama ,pero para cambiala por una motor mas grande es poco mas difficile .Tu encuentra una de secunda mano entero esta is differente pero montage entero con el pieces de el viejo con poco enginero constructivo (chapthero) yo pinthado es possiblie
Is there a main fuse that would of blown if I hooked my charger directly up to the + and - terminals on the starter on my 09 kymco venox 250 motorcycle?
Yes, there is likely a main fuse in your 2009 Kymco Venox 250 motorcycle that could have blown if you connected the charger directly to the + and - terminals on the starter. Many motorcycles have a main fuse located close to the battery or the fuse box to protect the electrical system from overloads and short circuits.
When you connect a charger directly to the starter terminals or other critical electrical components, you risk damaging the electrical system and causing a short circuit. If there was a surge of current due to improper connection, it could have blown the main fuse to protect the rest of the electrical components on the bike.
To troubleshoot the issue and restore power to your motorcycle, follow these steps:
- Locate the Main Fuse: Check your motorcycle's manual or service documentation to find the location of the main fuse. It is often located close to the battery or in the fuse box.
- Inspect the Main Fuse: Remove the main fuse and visually inspect it. If the main fuse is blown, you will see a break in the metal strip inside the fuse. Replace the blown fuse with a new one of the same amperage rating.
- Check Other Fuses: Even though you mentioned that all the fuses are good, double-check all the other fuses in the fuse box to ensure none of them have blown.
- Check Battery Voltage: After replacing the main fuse, check the voltage of the battery using a multimeter. Ensure the battery has enough charge (around 12.6 volts or higher) to power the electrical components.
- Reconnect Charger Properly: If the battery voltage is low, connect the charger properly to the battery terminals (positive to positive and negative to negative) and charge the battery until it reaches an appropriate level.
- Recheck Power: Once the battery is charged and all fuses are confirmed to be good, turn the key on and check if the lights and gauges receive power.
If you have followed these steps and still do not have power to the motorcycle, there might be other electrical issues caused by the improper charger connection. In that case, it's recommended to seek the assistance of a qualified motorcycle mechanic or electrician to diagnose and fix the problem correctly.
7/29/2023 10:33:01 PM •
Kymco...
•
Answered
on Jul 29, 2023
Not finding what you are looking for?