kawasaki KX 250 - Answered Questions & Fixed Issues
Clutch wont disengage 250 kx 250
Here's how I'd try to fix the clutch:
1.) Try to adjust the cable at the handlebar; usually there's a little bid of clutch lever travel (like 1/4"-1/2") before the clutch disengages. For right now, adjust the clutch so that there isn't any play and the adjustment all the way out. If the clutch disengages the transmission, then you know you have to fiddle with the cable to get it adjusted properly.
2.) The clutch plates could be sticking: here you'd have to take the clutch cover off and get to the clutch. Remove the clutch (usually an impact is ideal for removing the clutch holding nut. Take the clutch apart (steels and clutches), make sure they aren't sticking together. Then dip the clutches in oil, then reassemble.
3.) Sometimes the clutch basket (holds all of the clutches and steels in a "basket") gets grooves in it. These grooves prevent the clutch from disengaging. Sometimes you can file the clutch basket fingers down to remove the grooves. Alternatively, if the clutch basket fingers are really worn, you may have to replace the clutch basket.
Typically, when your in the clutch side of the engine case, I'd examine 2 and 3 (above) at the same time.
I have a 2006 Kawasaki
check for the fuel filter in the bottom of the gas tank attached directly to the outlet
How do I change the shift shaft on my 2000 kx250?
First, did it break or is it bent or is it stripped? These all require different approaches once you get the right side of the engine clear, clutch removed, etc... TAKE PICTURES WHILE YOU ARE DOING THIS to make sure you put everything back where it belongs. Do you have a clutch hub holder? (IMPORTANT) Do you have a air wrench, you will have a large clutch nut (24-26MM?) to remove and then reinstall the nut with the correct torque! If you do not have these tools, PLEASE take it to a PROFESSIONAL. He will have all the tools necessary. If the shift shaft is broke or bent it is going to be more difficult because it is a tight fit through the engine cases, they are aluminum and they will break if the shaft is forced out!! You will have to carefully saw the shaft off CLOSE to the case as possible before attempting to remove it.
If its just stripped, it can be filed or sanded down, cleaned, and removed easily. Change the shift shaft seal too!!!
If this is your first time to try this... and you don't have any of the tools I mentioned, PLEASE take it to a professional!!
Timing
Sounds like a valve timing problem to me. Put the engine at TDC (top dead center). There will be marks on the cam gear that should be aligned with the top of the head casting. This is something that could be damaging to the engine so be careful. A manual is a good investment.
Wont engage in 3rd gear
Bent shift fork is your problem.1st and 2nd working fine,wont go into 3rd,replace the shift fork and stop being so hard on the shifter.Costs a lot of money to fix these toys.
Backfire thru exaust on a 2004 kx 250
remove stator cover and flywheel (puller required), verify crankshaft key is not sheered, and stator plate is in its proper position. There is no timing mark on that flywheel because it is irrelevant and not needed.
This is most likely not a flywheel timing issue but a CDI timing issue. The CDI timing is governed by the TPS switch on the carburetor telling the CDI when to change timing maps and curves. If the carburetor is dirty and you cranked up the idle to run off the main circuit instead of the proper idle circuit this can happen. Or you have an improperly set, or failed TPS switch on the carb.
Need to change kick start
Hi, i am sorry but you dont say what the model of your machine is, this would help me determing the correct, answers for your questions, most kickstart springs can be changed by simply removing the clutch cover followed by the kickstarter shaft and then replacing the spring, make a note of kickstart stop location carefully remove the shaft holding the gears together replace the spring followed by the. Replacing the shaft and tensioning the spring before cover replacment, oil,etc. Some machines the shaft and spring is inside the centre cases and a complete engine strip is ness
Rim repair wanganui
A weld will ruin the temper of the metal, it will fail. A rim that cracked probably is weak elsewhere.
Not finding what you are looking for?