Husaberg Motorcycles - Popular Questions, Answers, Tips & Manuals


Hi, Lance and the usual suspects are:
1. Fouled spark plugs.
2. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Loose connection at ignition coil or plug between ignition sensor and module.
5. Spark plug cables in bad condition, shorting/leaking, spark plug cable connections loose check for spark leakage in the dark.
6. Faulty ignition coil or electronic control module.
7. Faulty pulse coil.
8. Faulty CKP, CMP, or BAS sensor.
9. Faulty ignition switch.
10. Faulty run/off switch
11. Tilt sensor needs a reset.
12. Security alarm failing to disarm needs reset
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
2003 FS 650 No spark Husaberg Forum
husaberg what they don want you to know
HUSABERG FE 450 Repair Manual
http://www.husaberg.no/Teknisk%20data%20Husaberg/Delekataloger/Firetakt/2000-2008/2003parts.pdf
Husaberg 400 User Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2003 Husaberg Fe... | 156 views | 0 helpful votes


Hi, Anonymous and the usual suspects are:
1. Spark plugs in bad condition or have an improper gap or are partially fouled.
2. Spark plug cables in bad condition.
3. Battery damaged or nearly discharged, should have 12.5 volts.
4. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Throttle controls not adjusted correctly.
6. Water or dirt in the fuel system.
7. Water or dirt in the carburetor.
8. Intake air leak.
9. Fuel tank vent hose and vapor valve plugged, or fuel line closed off, restricting fuel flow.
10. Choke valve inoperative.
11. Engine lubricant to heavy (winter operation).
12. Ignition is not functioning properly (possible sensor failure).
13. Faulty ignition coil.
14. Valves sticking.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Starting problem Husaberg FE400 03
2003 fe400e starting problems
http://www.husaberg.no/Teknisk%20data%20Husaberg/Verkstedhandboker/RA_Husaberg_2005_E_05.pdf
Husaberg Parts Dirt Bike Motocross
Husaberg 400 User Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2000 Husaberg Fe... | 57 views | 0 helpful votes


Hi, Jonti16 and the usual suspects are:
1. Fouled spark plugs.
2. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Loose connection at ignition coil or plug between ignition sensor and CDI box.
5. Spark plug cables shorting or leaking, spark plug cable connections loose, check for spark leakage in the dark.
6. Faulty ignition coil, pick up coil, trigger coil or CDI box testing needs to be checked with an ohmmeter at 70 degrees Fahrenheit
7. Faulty safety switches clutch, kickstand, neutral, off/on etc.
8. Faulty ignition switch.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
No spark AGAIN
husaberg what they don want you to know
HUSABERG FE 450 Repair Manual
http://dirtypart.com/manuals/filer/Husaberg/Husaberg%20Repmanual%20-05.pdf
http://dirtypart.com/manuals/filer/Husaberg/Husaberg%202001-2002%20SPARE%20PARTS%20MANUAL.pdf
Husaberg 400 User Manual
HUSABERG FE 450 EU Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2002 Husaberg Fe... | 50 views | 0 helpful votes


The main fuse protects all power consumers of the vehicle. It is located in the starter relay housing under the air filter box lid. (A spare fuse is located in the starter relay)

The fuse box containing the fuses of individual power consumers is located under the seat

Husaberg... | 56 views | 1 helpful votes


Hi, Pete and the usual suspects are:
1. Severely drained or faulty battery.
2. Faulty regulator/rectifier or high output coil.
3. Faulty power valve, solenoid or installation.
4. Clogged air filter or exhaust.
5. Cracked or incorrect float level.
6. Float needle is not seating.
7. Faulty reed valve.
For more information about your question please visit the website below. Good luck and have a nice day.
HUSABERG Pure Enduro Service

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Husaberg... | 75 views | 0 helpful votes


Hi, Anonymous for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix/test or parts inquiry. If necessary transport your vehicle to the dealer or shop and have a professional technician take it for a test drive, if it is in running condition, and give you a written estimate of repairs and answer any specific questions you may have about your issue. For more information about your issue please visit the website below. Good luck and have a nice day. DOWNLOAD 2010 Husaberg Fe 390

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2010 Husaberg FE... | 84 views | 0 helpful votes


Start by sticking the plug to a head bolt for a spark if that don't work the only way u can test it is with a different cdi

2001 Husaberg Fe... | 135 views | 0 helpful votes


Hi, Barry it's nonadjustable for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Husaberg, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.topspeed.com/motorcycles/motorcycle-reviews/husaberg/2013-husaberg-fe-350-ar148843.html
KTM 350 Valve Adjustment And Camshaft Swap
http://www.datamanagement-le-blog.com/fe350_service_manual_download.pdf
https://www.rockymountainatvmc.com/Parts-Finder/11057/2013-HUSABERG-FE-350
https://paitandacent.files.wordpress.com/2015/08/husaberg-fe-350-owners-manual.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Husaberg Fe 400... | 58 views | 0 helpful votes


Its a long shot, but try Youtube.
They have tons of DIY videos.

Husaberg... | 65 views | 0 helpful votes


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Husaberg, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?q=Kick+start+shaft+replace+2000+Husaberg+Fe+600+E+SM&tbm=isch&source=univ&sa=X&ved=2ahUKEwjikaecianiAhXmzVkKHW9sAFkQsAR6BAgIEAE&biw=1440&bih=757
Kickstart Replacement and More
http://mail.lumate.fi/husaberg_service_manual.pdf
https://www.rmstator.com/en_ww/list/parts/Motorcycle/2000/Husaberg/FE_600_E/--
https://www.manualslib.com/manual/1088074/Husaberg-Enduro-Fe-400.html#product-ENDURO%20FE%20600

2000 Husaberg Fe... | 51 views | 0 helpful votes


gday there have you cleaned the earth lead and positive lead on the ones going to the battery if you have then have you checked that your new battery has charge in it between 13 to 14.2 volts as some batteries do not come charged or if it is a acid type battery it may not have acid in it ,you probably would have checked this already but just a thought my end ,if all is good there did you accidently put the terminals on wrong for a second if you made a mistake like that the fuse may have blown ,easy done,if not check with a multimeter from your battery back to your starter soliniod and if all good there then check back from that .hope this helps cheers

Husaberg FE 550... | 84 views | 1 helpful votes


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Husaberg, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.ultimatespecs.com/motorcycles-specs/honda/husaberg-fe-400-e-2003
http://husaberg.org/mechanical/19634-oil-level.html
https://www.emanualonline.com/Motorbikes/Husaberg/FE-Models.htm
http://www.cyclebuy.com/husaberg/parts.htm
Husaberg 400 User Manual

Husaberg Fe 400... | 34 views | 0 helpful votes


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Husaberg, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?q=Replace+the+battery+2002+husaberg+470-fxe&source=lnms&tbm=isch&sa=X&ved=0ahUKEwjHooyGkObiAhXqqFkKHcIWB3kQ_AUIESgC&biw=1440&bih=757
http://husaberg.org/electrical/9274-new-owner-fx-470-2002-battery-replacement-question.html
http://husaberg.org/mechanical/11215-workshop-manual.html
http://www.cyclebuy.com/husaberg/parts.htm
https://www.manualslib.com/manual/640214/Husaberg-05.html

Husaberg... | 50 views | 0 helpful votes


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Husaberg, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://husaberg.org/electrical/16633-values-ignition-coil-stator.html
https://www.google.com/search?q=Coil+resistance+2003+Husaberg+Fe+501+E&tbm=isch&source=univ&sa=X&ved=2ahUKEwjW6tHcgObiAhWLv1kKHY7YC8kQsAR6BAgGEAE&biw=1440&bih=757
http://husaberg.org/mechanical/11215-workshop-manual.html
http://www.cyclebuy.com/husaberg/parts.htm
https://www.manualslib.com/manual/1088074/Husaberg-Enduro-Fe-400.html#product-FE%20501%20e

2003 Husaberg Fe... | 235 views | 0 helpful votes


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Husaberg, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?q=Wiring+diagram+2010+Husaberg+FE+390&tbm=isch&source=univ&sa=X&ved=2ahUKEwjDuJn0kebiAhVRs1kKHf0YB_8QsAR6BAgFEAE&biw=1440&bih=757
http://husaberg.org/electrical/13053-2010-fe-390-wiring-diagram.html
https://www.ebay.co.uk/itm/Husaberg-service-manual-2010-FE-390-EU-AUS-USA-FE-450-EU-AUS-USA-/262979751487
http://www.cyclebuy.com/husaberg/parts.htm
http://husaberg.org/service-manuals/17516-2010-husaberg-fx-fe-390-450-570-owners-manual.html

2010 Husaberg FE... | 167 views | 0 helpful votes


Hi, Anonymous and the usual suspects are:
1. Fuel cap or fuel tank is not venting properly.
2. Fuel filter clogged.
3. Fuel line pinched or kinked.
4. Vacuum line from the petcock to intake manifold cracked.
5. Float needle and seat sticking.
6. Float level too low.
7. Carburetor bowl vent line clogged/blocked/pinched.
8. Idle adjusting screw set too low.
9. Air/fuel mixture screw set too lean.
10. Idle port, transfer ports, slow air jet clogged.
11. Slow fuel jet clogged.
12. Faulty fuel pump.
13. Faulty auto choke or wiring connection.
For more information about your issue and valuable "Free" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://husaberg.org/fuel/5956-only-runs-choke-any-hints.html
WHY your motorcycle only runs on CHOKE
https://www.repair-manuals.eu/cat/motorcycle_repair_workshop_manuals/repair_manuals_husaberg
http://www.cyclebuy.com/husaberg/parts.htm
https://www.manualslib.com/manual/813892/Husaberg-E-400-E.html#product-FC%20550/4

Husaberg... | 44 views | 0 helpful votes


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Husaberg, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://husaberg.org/mechanical/21372-fe550-valve-clearance-spec.html
https://www.youtube.com/watch?v=TnKYEbRzKic
http://www.husaberg.no/Teknisk%20data%20Husaberg/Verkstedhandboker/RA_Husaberg_2005_E_05.pdf
http://www.cyclebuy.com/husaberg/parts.htm
https://www.manualslib.com/manual/640214/Husaberg-05.html

2006 Husaberg FE... | 58 views | 0 helpful votes


Hi, Anonymous and the usual suspects are:
1. Severely discharged or a damaged battery must have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
2. Faulty alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. A faulty main circuit breaker or ignition switch, check for loose connections and continuity.
5. Faulty system relay or ignition relay, check for continuity.
6. Faulty ignition coil, ignition/electronic module.
7. Faulty CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Faulty neutral, side stand or clutch lever safety switch.
10. Fuel tank empty
11. Fuel tank contaminated with ethanol sludge.
12. Water or dirt in the fuel system, or clogged filter.
13. Quick disconnect check ball stuck.
14. Restricted, blocked or kinked fuel line.
15. Faulty fuel pump.
16. Faulty pressure regulator.
17. Faulty or clogged fuel injectors.
18. Lean angle switch is faulty or needs adjustment.
19. Catastrophic engine failure, perform a compression test.
For more information about your issue and valuable "FREE" downloads that you need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://thumpertalk.com/forums/topic/774831-2010-husaberg-390-dying-after-2-days-help
http://www.dirtbikeworld.net/forum/archive/index.php/t-76040.html
https://www.manualslib.com/manual/1235895/Husaberg-Fe-450-Eu.html
http://www.cyclebuy.com/husaberg/parts.htm
HUSABERG FE 450 EU Owner Manual

2010 Husaberg FE... | 142 views | 0 helpful votes


Hi, Anonymous and the usual suspects are:
1. Severely discharged or a damaged battery must have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
2. Faulty alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. A faulty main circuit breaker or ignition switch, check for loose connections and continuity.
5. Faulty system relay or ignition relay, check for continuity.
6. Faulty ignition coil, ignition/electronic module.
7. Faulty CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Faulty neutral, side stand or clutch lever safety switch.
10. Fuel tank empty
11. Fuel tank contaminated with ethanol sludge.
12. Water or dirt in the fuel system, or clogged filter.
13. Quick disconnect check ball stuck.
14. Restricted, blocked or kinked fuel line.
15. Faulty fuel pump.
16. Faulty pressure regulator.
17. Faulty or clogged fuel injectors.
18. Lean angle switch is faulty or needs adjustment.
19. Catastrophic engine failure, perform a compression test.
For more information about your issue and valuable "FREE" downloads that you need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://thumpertalk.com/forums/topic/774831-2010-husaberg-390-dying-after-2-days-help
http://www.dirtbikeworld.net/forum/archive/index.php/f-93.html
https://www.emanualonline.com/Motorbikes/Husaberg/FE-Models.htm
http://www.cyclebuy.com/husaberg/parts.htm
Husaberg 400 User Manual

2010 Husaberg FE... | 23 views | 0 helpful votes


i will assume that you have an old bike with a good engine but with a dirty starter, what i mean is inside. my idea is the same as you have and i also experience the same with my bike. if you can remove the starter and open anyway it has only two screw and clean contacts and carbon brush by any available contacts cleaning agent..

2009 Husaberg FE... | 76 views | 1 helpful votes

Not finding what you are looking for?
Husaberg Logo

222 questions posted

Ask a Question

Usually answered in minutes!

Top Husaberg Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6480 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Bill Boyd

Level 3 Expert

53816 Answers

Are you a Husaberg Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...