Harley Davidson Motorcycles - Answered Questions & Fixed Issues


The Dyna battery can be removed by:
1. Remove the seat.
2. Remove negative connection at frame, and positive connection at battery.
3. Remove the lower rear bolt. (left side of battery box at frame upright)
4. Remove hte upper rear bolt, and swing down the battery box.
5. Remove the top cover, and side cover.
6. Lift battery out, and remove negative cable from battery.

2001 Harley... | Answered on Jan 15, 2020 | 864 views


Hi, Peter starting in 1996 Harley made available an optional security system with a Button Key Fob that had to be depressed to arm and disarm the system. In 2007 the smart security system was introduced in European countries with a buttonless proximity sensor Fob that only works within a 10-foot radius depending on battery strength and sensor receiver location. In 2012 Smart Security Systems became standard equipment on some models. In 2015 it was standard on all models. The following is a list of security system FOB failure:
BUTTON FOB'S
1. The FOB battery is weak or dead.
2. A new battery was installed upside down.
3. The FOB is no longer recognized by the security system and needs to be reprogrammed by the dealer.
PROXIMITY SENSOR FOB'S
1. Fob is more than 10 feet away from the bike.
2. The FOB battery is weak or dead.
3. A new FOB battery was installed upside down.
3. The security receiver antenna is broken.
4. The FOB is no longer recognized by the security system and needs to be reprogrammed by the dealer.
There is an option to override the security system by inserting a pre-programmed pin number. This is a 5 digit number that comes from the factory as 1-2-3-4-5. If you read your owners manual it "HIGHLY" recommends that you change this number to a personal one. You can do this yourself but it is complicated and tricky sometimes it works sometimes it doesn't. I have a 2003 FLHTCUI that the procedure did not work and had to go to my local dealership to have the system reprogramed to my own personal number. They wanted $50 for this 2-minute service but after explaining that I was a 40 year retired Harley wrench and waving a $20 bill to the service writer got me through. Money talks but not all the time.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at [email protected] Good luck and have a wonderful day.
https://www.hdtimeline.com/threads/2007-fatboy-alarm-issues-help.29926/
http://www.mediafire.com/file/lbs9ej75cinadd3/2007+Harley+Softail+Service+Manual.pdf
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
https://ownersmanuals2.com/harley-davidson/fat-boy-2007-owners-manual-66494
https://www.6ya.com/how-6ya-works $6

Harley Davidson... | Answered on Jan 14, 2020 | 23 views


Hi, Jeffrey "manual" for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at [email protected] Good luck and have a wonderful day.
https://www.youtube.com/watch?v=oEEdGq901K8
http://www.mediafire.com/file/uwq02sfdx8kv37v/2006_Harley_V-Rod_Service_Manual.zip/file
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
https://ownersmanuals2.com/harley-davidson/vrsca-v-rod-2006-owners-manual-66484
To speak to me personally $6

Harley Davidson... | Answered on Jan 12, 2020 | 18 views


the post should be the same as an original. The wires should be green and tan. Green wire goes to the post towards the front wheel and the tan to the post nearest the engine. Don't forget to "polarize" the generator before starting. procedure is in the service manual. Momentarily short between the battery positive post and the field terminal.

1979 Harley... | Answered on Dec 07, 2019 | 1,336 views



P0262 = FRONT INJECTOR HIGH

Possible causes
- Dirty Fuel Injector 1
- Faulty Fuel Injector 1
- Plugged Fuel Injector 1
- Fuel injector 1 harness is open or shorted
- Fuel injector 1 circuit poor electrical connection
Tech notes
Clogged or partially clogged fuel injector can cause this code. Start by performing an injector flush before replacing the injector.
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Engine Misfire
- Engine Run Rough
- Low MPG
P0262 Description
Code P0262 is triggered when the Engine Control Module (ECM) detects a low voltage in the Fuel Injector 1 Circuit. During normal conditions theECMturns the Fuel Injectors ON and OFF in the Fuel Injection System.

2004 Harley... | Answered on Dec 06, 2019 | 386 views


take it to the dealer, set up problem with EFi

2005 Harley... | Answered on Dec 06, 2019 | 58 views


In the panel box under the seat

Harley Davidson... | Answered on Dec 06, 2019 | 84 views


So you will first disconnect the battery then take the center counsel off and remove the t25 screws carefully pull assembly out and change filter

Harley Davidson... | Answered on Dec 06, 2019 | 43 views


The switch is insulated so wires can go either way.

Harley Davidson... | Answered on Dec 06, 2019 | 44 views


No, use new fasteners as they are one use only, use locktite and torque accurately

Harley Davidson... | Answered on Dec 06, 2019 | 222 views


1. Start by prying the metal ignition cap where the key would usually go off to get to the wires. 2. Twist the battery and ignition wires together to complete the connection and send power from the battery to the motorcycle's ignition. Alternate Method 1. You can clip the wires on the bottom of the ignition. Only clip the red wire and the solid green wire. If there is no green wire, look for a solid yellow or black wire. Various colors are used to prevent non-professional tampering. The battery is always red and green, yellow, and black are the ground/ignition wires. Only clip the previously mentioned wires and leave the other wires alone, especially any "stripped" wires!

2002 Harley... | Answered on Dec 06, 2019 | 17,698 views


Connect it to a Code Reader and find out what the issue is? Then fix the issue and reset the check light. The proper name is an 'Engine Malfunction Light'. It shows a problem that needs addressing.

Harley Davidson... | Answered on Dec 05, 2019 | 44 views


.038" - .043" per Harley Davidson ....set at .040

Harley Davidson... | Answered on Dec 05, 2019 | 126 views


Cal the dealer.

Harley Davidson... | Answered on Dec 05, 2019 | 43 views


under the seat where the battery is at

Harley Davidson... | Answered on Dec 05, 2019 | 147 views


Sounds like it is operating as it should now. Maybe it was a software update. Why would you want to risk starting it in gear?

Harley Davidson... | Answered on Dec 05, 2019 | 46 views


Does it un screw on my 75 flh there was a small screw. http://www.hdtalking.net/ check here 2..

Harley Davidson... | Answered on Dec 05, 2019 | 397 views


Jumper solenoid post to post ( large Cables ) with battery jumper cable. If it starts bad solenoid.

Harley Davidson... | Answered on Dec 05, 2019 | 63 views


Hi Tamara,
possible cause is the connector on the side of the throttle body. This connector will be facing towards the rear of the motorcycle just behind the air filter box. Disconnect it and spray a good quality switch cleaner with lubricant into the connector or use the HD contact grease and put a small amount into each contact hole. Then insert and remove the connector a couple of times before finally leaving it in position. I have got this fault a few times and this proved to be a cure.

Harley Davidson... | Answered on Dec 05, 2019 | 66 views


the click means the start relay is getting power,just not enough or it may be bad.Check cables to the starter from start relay also.

2000 Harley... | Answered on Dec 05, 2019 | 941 views

Not finding what you are looking for?
Harley Davidson Logo

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6103 Answers

Mike

Level 3 Expert

4367 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...