Zastava Cars & Trucks - Recent Questions, Troubleshooting & Support


Irrelevant

Cars & Trucks | Answered 14 hours ago


Comment. Unidentified object

Cars & Trucks | Answered 16 hours ago


While plugs are the most common issue, as well as coils and wires, have you checked the fuel injection system for issues as well as looking for an air intake leak? Fuel issues and an intake leak will also cause a P0303 code

Cars & Trucks | Answered 17 hours ago


Locate the timing mark pointer plate beside the crankshaft pulley. The "0" mark represents top dead center. The pointer plate will be marked in either one or two-degree increments and should have the timing mark for your 2.8L V6 engine noted.

If it's not noted on the plate, check the VECI label under the hood for the correct number, then count count back from the "0" mark to the correct number of degrees before top dead center.

Cars & Trucks | Answered 18 hours ago


If you go to an AutoZone and give them all the information on your vehicle they can tell you which wiring kit you need and it will have a wiring diagram included or on the back of the box. Hope this helps you out.

Cars & Trucks | Answered 19 hours ago


When the pressure indicator is solid yellow, the sprayer is
operating between 200 and 1800 PSI. A solid yellow pressure
indicator means:
• The sprayer is at the proper pressure setting for spraying
stain, lacquer, varnish, and multi-colors
• If the pressure indicator goes to solid yellow when the
pressure is set so that it starts at solid green, it indicates
one of the following:
a. Tip Wear Indicator - when spraying with latex or at high pressure, the solid yellow appears. This means the tip is worn and needs to be replaced.
b. Tip Too Large - when a tip that is too large for the sprayer is put in the gun. The pressure indicator will turn from solid green to solid yellow.
c. Fluid Section Wear - if a solid yellow pressure indicator appears when using a new tip and the pressure is set at maximum, service may be required due to worn packings, worn piston, stuck valve, etc.

Cars & Trucks | Answered 20 hours ago


Do not try to reattach the mirror to the arm while it is still on the windshield as this can lead to damage.

Remove the base of the mirror arm from the windshield. There should be a little screw that secures the mirror to the metal piece that is glued to the windshield. Loosen the screw and then slide the arm upwards towards the roof and it should slide right off.

Next, take your mirror and place it into a flat surface, while placing a towel between the mirror and the surface to prevent scratching. Next, take the arm and line up the male and female ends of the ball socket.

Now you will need to apply quite a bit of pressure to get the pieces to mate together.

Then you can reattach the mirror back to the windshield.

Cars & Trucks | Answered 21 hours ago


Fuses that "look good" may actually be open. More likely, some switch component burned open.

Cars & Trucks | Answered Yesterday


Google is your answer;
https://www.landyzone.co.uk/land-rover/how-to-open-the-bonnet-on-a-freelander-1-when-the-cable-snaps.315737/

Cars & Trucks | Answered Yesterday


DTC P2101-
The commanded throttle position (TP), based on accelerator pedal position (APP) and possibly other limiting factors, is compared to the actual TP. The 2 values should be within a calibrated range of each other. Both the powertrain control module (PCM) and the throttle actuator control (TAC) module redundantly monitor the commanded and actual TP. This DTC sets if the PCM detects an out-of-range condition between commanded and actual throttle position.
DTC P1516
The predicted throttle position (TP) is compared to the actual throttle position. The two values should be within a calibrated range of each other. Both the powertrain control module (PCM) and the throttle actuator control (TAC) module redundantly monitor the predicted and actual throttle position. This DTC sets if the PCM detects an out of range condition between the predicted and actual throttle position.

Do you know what electronic throttle control is ?

Pt 1 2007 Chevy 2500HD Reduced Engine Power Warning Fault Code P1516...

Cars & Trucks | Answered Yesterday


Contact Viking directly to request the diagram.

Cars & Trucks | Answered Yesterday

Not finding what you are looking for?
Zastava Logo

Family Lines

0 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Zastava Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

john h

Level 3 Expert

23424 Answers

Are you a Zastava Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...