Question about 2000 Chrysler Concorde

1 Answer

Where is your cam position sensor located? and where is the crank shaft position sensor at?And could you send a diagrm or something to show?

Posted by armindanorri on

Ad

1 Answer

Adam Scott Roberts

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points
    All-Star:

    An expert that got 10 achievements.
    MVP:

    An expert that got 5 achievements.
    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,243 Answers

The cam sensor is located on top of the engine in the front of the left side valve cover. the crank sensor is located on the right side of the engine block just above the starter.

Posted on Jul 17, 2011

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

What are the probable causes of DTC P0335-725?
Crank shaft sensor.

Dec 13, 2015 | 2006 Nissan Sentra

1 Answer

Where does the crank angle sensor go on a 1990 dodge daytona es turbo and what does it do
crank angle sensor, Crank position sensor ,reads the position in degrees of the crankshaft. When the sensor reads a set point on the crankshaft it sends a signal to the ECM(CPU) program which then triggers the spark for that positioned cylinder. It also triggers the injector to squirt. Without it the CPU will not know when to set the spark or injector so nothing works.It is constant for all ECM controlled engines regardless. Further the cam shaft position sensor sends a signal to the cpu telling it that the valves are in the correct position for spark,fuel. When the cam belt/chain breaks there is no position regestired so the spark and fuel are shut off

Dec 05, 2014 | 1990 Dodge Daytona

1 Answer

Need to know how many sensor. is on my transmission.. 2003 Pontiac Montana v 6 .. can you show me picture where transmission control solenoid goes?
There are 12 common sensors and 10 internal sensors. The most common that often fail (MAP), (TPS), (CAM), (IGN), (CRANK) MAP is your mass air flow which is located at the beginning of your air intake, TPS is the throttle body position sensor, the CAM is the cam shaft position sensor (transmission), IGN ignition position sensor and the CRANK sensor is located near the bottom driver side front

Oct 26, 2013 | 2003 Pontiac Montana

1 Answer

I have a 2003 chevy malibu with 90,000 miles. i took it in for maintenance and the mechanic said that it was showing trouble code p0341. he said it was the cam sensor. yesterday when i went to start it, it...
if the cam sensor is bad, it will definitely not start. The cam shaft position sensor's function is: the engine speed and crankshaft position information is supplied frome a sensor which is usually situated at the front or rear of the crankshaft. note that distributor-located engine speed sensor are generally being replaced with crank shaft-located sensors,as worn disributor drives and associated components can effect the accuracy of the engine speed signal.

A camshaft position sensor,or cylinder identification sensor is used to determin the engine cycle position the information is used to provide individual cylinder ignition and injection cotrol.Many engine mangement systems use an inductive type of sensor that is located near the camshaft;when the camshaft rotates a single signal is passed to the ECU to indicate a reference point in the engine cycle

May 03, 2011 | 2003 Chevrolet Malibu

0 Answers

1996 Jeep Grand Cherokee 4wd v6. Car would not start. We change the crank shaft position sensor and the car started with no problem. 1 month later when we start the car the check engine light comes on...

Apr 05, 2017 | 1996 Jeep Grand Cherokee

1 Answer

My nissan is showing codes p00340 and p00325. p00340 is a cam sahft position sensor but my yeat of car does not come equipt with a cam shaft position sensor. instead i replaced the crank shaft position...
i believe that car comes with a dist,it has a cam sensor built end it.

Sep 20, 2010 | 1996 Nissan Altima

1 Answer

Ok i have a cam sencer problen have replace sencer and magnet it still cuts the car off and showes the same code
Try replacing the "Crank Shaft Position Sensor" this two sensors "Cam" and "Crank" communicate so if one is acting up it sends the wrong signal to the computer, I recently had the exact same problem but in reverse and a different vehicle, the other thing, although not very usual is the wire harnnes that connects to the sensor itself could not be working properly. Good Luck!

Sep 06, 2010 | 1989 Buick Riviera

1 Answer

I would like to know if the cam sensor and the crank shaft sensor are one of the same or two different items
They are two different items. The cam sensor reports the position of the cam shaft(s) which operate the valves. The crank shaft sensor reports the position of the crank shaft, ie the position of the pistons.

May 19, 2010 | 1998 Chevrolet Malibu

2 Answers

What is a cam crank sensor on 2004 Audi A4
The "cam crank" sensor is the "reader" for position and speed of the camshaft. This sensor send informations to Engine Control Unit about camshaft position and speed. If the sensor is faulty engine stops!

Oct 23, 2009 | 2004 Audi A4

1 Answer

Where is the cam shaft position sensor located on a 2001 gmc 5.7 , and also the crank position sensor?
If this is a 5.7L the cam sensor is in the distributer and the crank sensor is in the timing cover

Dec 16, 2008 | 1995 GMC Jimmy

Not finding what you are looking for?

View Most Popular

2000 Concorde

  • Cars & Trucks

Related Question

What are the probable causes of DTC P0335-725?

  • 2006 Nissan Sentra

Open Questions:

0 Answers

2000 Concorde wipers work using washer but not otherwise. All other column lever functions work. Is this a switch problem? I just had the dash removed/reinstalled for a heater/ac issue. There wasn't a problem before that. Suggestions?

Jul 22, 2018 | 2000 Chrysler Concorde

0 Answers

I have a 2000 chrysler concorde 3.2 liter V6 and noticed one key works and the other key doesn't. Both keys chips are good. What is wrong with the key that doesn't work?

Apr 24, 2018 | 2000 Chrysler Concorde

0 Answers

2000 Concorde, rear sway bar bushings need to be replaced but the bolts just spin. HELP!

Apr 20, 2018 | 2000 Chrysler Concorde

0 Answers

Where is starter relay located?

Oct 05, 2017 | 2000 Chrysler Concorde

See all 2000 Chrysler Concorde Questions

Related Topics

2000 Chrysler Concorde Logo

328 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

1 Answer
Cost to replace tie rod ends parts and labour

1999 Chrysler Concorde

1 Answer
Trouble codes P0420 P1681 P0344

Chrysler Concorde Cars & Trucks

1 Answer
Fuse box diagram

Chrysler Concorde Cars & Trucks

2 Answers
How do i remove a battery from a 2002 chrysler

2002 Chrysler Concorde

1 Answer
Where is starter located on 2004 chrysler

Chrysler Concorde Cars & Trucks

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14866 Answers

Mike

Level 3 Expert

4372 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...