Question about 1995 Toyota Camry

1 Answer

O/d light blinks when driveing o/d seems to be engaged car has 198000 miles and runs very good also engine light is on

Posted by loyd_dodd_ag on

Ad

1 Answer

raj somaiya

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 5,370 Answers

O/D light blinks, but with that the check engine light is ON.--- This will make your troubleshooting easier.When the check engine light comes on, and remains on, this indicates that there is error stored in your cars computer.---- Once the computer is scanned, you will get error codes, as per that error code it will point towards faulty part, which is causing the O/D light to blink.-------- Most probably the O/D light blinks, If a problem exists in No. 1 or No. 2 solenoids or speed sensors .
--------------- For car after 1995 it requires OBD2 tool and for car before 1995 it requires OBD1 tool.------- --------- You car will require OBD1 tool.There are very few auto parts store and repair centers who have OBD1 tool.In your case you required OBD1 tool.------ You can just contact local auto-parts store and they will guide you to the nearest store who has OBD1 tool.There you can get your car scanned.If there is error set in your cars computer, then you will receive the error code.As per error code it will point towards the faulty part causing this problem in your car.------------- -------------- The codes which you get is scanning will be mostly any of this following codes:--- DTC P0500 - Vehicle Speed Sensor Malfunction
. DTC P0750 - Shift Solenoid "A" Malfunction
. DTC P0753 - Shift Solenoid "A" Electrical Malfunction
. DTC P0755 - Shift Solenoid "B" Malfunction
. DTC P0758 - Shift Solenoid "B" Electrical Malfunction
. DTC P0770 - Shift Solenoid "E" (SL) Malfunction
. DTC P0773 - Shift Solenoid "E" (SL) Electrical Malfunction
. DTC P1520 - Stop Light Switch Signal Malfunction
. DTC P1705 - Direct Clutch Speed Sensor Circuit Malfunction
. DTC P1765 - Shift Solenoid Valve SLN Circuit Malfunction
. DTC P1780 - Park/Neutral Position Switch Malfunction
--------------- Now it all depends on what code you get, as per that you can replace the following part.------- This will help.Thanks.Helpmech.

Posted on Jul 07, 2011

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Lincoln town car traction control light comes on. unable to know how to fix the problem


do u have an ABS light on at all if so some vehicles use the wheel sen to detect if s wheel is slipping

Mar 04, 2015 | 2005 Lincoln Town Car

1 Answer

4wd auto shift does not engage 4wd.


for 4wl need to be stopped and put in neutral or park it wont actuate while driving [ blinking light indicates failure to engage ] 4wd hi can do while driving --if fails also then check and test for actuator sticking --control module --or transfer case failure

Oct 19, 2017 | 2000 Chevrolet Silverado 1500

1 Answer

2000 tundra 4wd takes forever to engage, 4 low will not


try pushing button and then put in reverse back up a bit and then put in drive see if it goes in quicker. put truck in nuetral befor putting into 4 low

Oct 01, 2012 | Cars & Trucks

1 Answer

Check engine light is on but seems to be running fine. is it ok to drive 25 miles to get it repaired


Yes, it if is running good you will do no harm driving it to get it repaired.

Oct 05, 2010 | 2004 Kia Sorento

1 Answer

Blinking green drive light


There is some problem with your transmission, get an engine analyser then you can see the error code i.e. telling the problem faced.

Apr 06, 2010 | 2005 Honda Pilot

1 Answer

My engine light just came on. i did purchase gas


a good rule of thumb for the gas cap is at least 3 clicks. if you fuel while running you will trigger the light. if it continues to stay illuminated, it would be a good idea to get it checked. it will come up with a small evap leak code. happy holidays

Dec 28, 2009 | 2006 Hyundai Tucson

1 Answer

Ford Escape engine light on/blinking, faint knocking noise


If your check engine light came on when the problem occurred, then you need to have the diagnostic codes read. I am cheap, so I would suggest going to an Advance or Auto Zone, they will read the codes and interpret them for you in hopes of selling you the part that will fix it. Good Luck. I hope you find this very helpful!

Nov 22, 2009 | 2005 Ford Escape

1 Answer

1995 Plymouth Neon Running rough now wont start


it could be, but first you might want to run a onboard dianostic. turn your key on and off (not to run position) 3 times, on the third time leave the key on your engine light will blink out codes.
(like for 12 it will blink once pause then blink 2 more times.) try this then let me know what the code is.
hope this helps

May 31, 2009 | 1995 Dodge Neon

2 Answers

Engine light on


A code P0420 may mean that one or more of the following has happened:
  • Leaded fuel was used where unleaded was called for
  • An oxygen sensor is not reading (functioning) properly
  • The engine coolant temperature sensor is not working properly
  • Damaged or leaking exhaust manifold / catalytic converter / exhaust pipe
  • Retarded spark timing
  • The oxygen sensors in front and behind the converter are reporting too similar of readings
  • That should get you going.

Mar 22, 2009 | 2001 Pontiac Montana

Not finding what you are looking for?
1995 Toyota Camry Logo

1,105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14850 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...