Question about Chevrolet Silverado 3500HD

2 Answers

Holes won't line up to put new starter in place. On the chevy 1ton pickup.

Posted by chrshans4 on

Ad

2 Answers

regulate24_7

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 14 Answers

If you have a small block there are only 2 kinds of starters a straight bolt pattern or slanted. Make sure your not putting a small block starter on a big block or vise versa. Also check the the starter specs for straight or slant bolt pattern.

Posted on Aug 13, 2011

Ad

Jonah Oneal

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 14,092 Answers

COULD BE WRONG STARTER CHEVY HAS MANY SIZE V8 ENGINES FOR TRUCKS ENGINES ARE 4.8 - 5.3 - 5.7 - 6.0 - 6.6 AND 8.1 POSSIBLE YOU HAVE WRONG STARTER.

Posted on Jun 27, 2011

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1988 2wd pickup and the starter won't


starter wont turn or engages the flext plate,flywheel and still wont turn engine over?if this is the case you have a seized up motor,but if it doesnt even click check signal wire from ignition switch for power when you turn the key to crank.if no power your ignition switch,park/neutral safety switch(clutch switch if manual trans) or wrongly installed wired could be the problem.

Jul 18, 2013 | Cars & Trucks

1 Answer

How many wires are on the starter in a 97 Chevy S10 4.3 pickup?


check the wires behind the alternator i had the same issuse it was a small eyelet wire or you could try a line from battery to power strip

Jun 16, 2012 | 1997 Chevrolet S-10 Pickup

1 Answer

Will a 2wheel drive transmission out of a 96 chevy 1ton fit in a 2001 3/4ton 4x4 chevy


2 wheel drive transmissions will not fit in a 4X4. Hope this helps.

Mar 04, 2012 | Cars & Trucks

1 Answer

Ok I replaced the ignition key switch.put a new starter on , new battery, got power to all above, however the starter won't turn over . There is no fuses blown . Checked at advance auto on my 91 pickup...


Car no start problem is sometimes very difficult to confirm. You try all the possible things, but still you get no fault and problem is still the same.--------
In that case, you need to check few things individually.
Check the spark,the battery,the crank, the fuel and other most possible parts. Click this link below for more details:-- http://howtobyme.blogspot.com/2011/10/car-troubleshooting-tips.html

Oct 21, 2011 | 1991 Toyota Pickup

1 Answer

Hello. My 1997 Chevy Tahoe refuses to start. The problems began with a bad fuel pump. I changed. It worked. The fuel pump died again. I changed it again and it has been working. I parked it for two weeks....


Now you have a good battery & a starter that turns over the motor

Have you cycled the key on & off with a fuel pressure gauge on the
fuel rail?

Do you have a fuel filter that isn't over 3 or 4 years old?

Have you checked for spark while cranking ? Use an old plug on the wires,
if you have ignition wires,don't ground the wire without resistance

If you removed the ducting & MAF Sensor it won't start

Tell us what you checked & exactly how that was done.

Jun 09, 2011 | 1997 Chevrolet Tahoe

1 Answer

I have a 1985 Chevy pickup and I want to put a newer model bench seat, how new can I look at, ie 1995, 2000, 2005????


You can likely put any one you want in there, if you don't mind drilling holes in the floor. As for the brackets actually lining up... don't know. Your best bet is to take a measurement and head for an auto wrecker to see what you can use.

May 11, 2011 | Chevrolet 1500 Cars & Trucks

1 Answer

Does front stablizer bar have to be removed to replace bushings for 1994 chevy c1500 pickup?


yeah i removed my stabalizer bar bushing and putting a new one in seems to be quite difficult to line up the holes to get the bolt straight enough to thread the nut on to it

May 03, 2010 | Cars & Trucks

2 Answers

Can i use a 96 4L80E transmission in a 2000 Chevy Express Van


that trans is a little to lite duty for a diesel, u can use it but u will need to install the computer and the correct wiring harness.

Mar 01, 2009 | 1995 Chevrolet C/K 2500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

205 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...