Question about Land Rover Discovery

Open Question

How do i set my land rover 4 weel drive - Discovery Land Rover Cars & Trucks

Posted by smash510 on

Ad

5 Related Answers

p38arover

  • 32 Answers

SOURCE: What is the ignition sequence on my Land Rover

Yes, from the workshop manual, the 1.8 litre K-Series engine
Firing order is 1 - 3 - 4 - 2

Download a copy of the RAVE CD off the 'Net and you'll have all the workshop manuals, owner's manual, electrical diagrams, etc.

Posted on Dec 05, 2009

Testimonial: "Timing on my '98 Land Rover Freelander was quite problem; if you don't have access to the spec sheets; but a sure answer from FIXYA.com saved the day"

Ad

Anonymous

  • 1 Answer

SOURCE: my land rover discovery is stuck in 4 wheel drive,

The discovery is as previously mentioned permanent four wheel drive.However the difflock/range lever in most suffers from lack of use and siezes all i had to do when i bought mine was plenty of WD40 and patience as i don't think it had been in low range or difflock from the day it was built.don't try to force it just spray it and let it soak then try keep doing this and it should free up if not it may be the selector grubscrew has worked loose just threadlock it and screw it back in.

Posted on Feb 16, 2010

Ad

jklisiewicz

  • 246 Answers

SOURCE: 1996 land rover discovery intake manifold gasket

oil from the pcv valve going into your intake manifold will cause a gasket to swell. but it should not be to the point where it's noticeable. you should probably replace the intake manifold gasket at this point.

Posted on Feb 16, 2010

Anonymous

  • 5 Answers

SOURCE: 2009 Land Rover Discovery and Blackberry Curve 8900

You'll have to call the dealer have them pull the VIN to see if you have the latest and greatest software. Also you can check on the land rover website under owners put in the last 8 digits of your vin number and it will tell you if the BB8900 is fully compatible.

Posted on Aug 15, 2010

dcramer531

Dcramer531

  • 1654 Answers

SOURCE: 2003 Land rover range rover

  • These instructions are for The range Rover, but I can't see them changing the steup

  • Park your Range Rover in a safe place, open the hood and disconnect the black, negative battery cable.

  • 2

    Locate the drive-belt tensioner pulley (this pulley does not drive any accessory on the engine but provides tension to the belt). If the pulley has a recessed squared in the middle, use a 1/2-inch drive-breaker bar to pivot the pulley toward the center of the engine, then slide the drive belt from under the pulley. Carefully release the tensioner pulley. On other models, the tensioner pulley comes with adjusting and pivot bolts. Use a wrench or ratchet and socket to loosen the bolts and release the belt tension. Other tensioner pulleys come equipped with a third bolt to prevent the adjusting bolt from sliding and releasing the belt tension. Loosen this bolt if necessary. On other vehicle models without a tensioner pulley, it is necessary to loosen the alternator mounting and adjusting bolts to release the belt tension using a wrench or ratchet and socket.

  • 3

    Slide the drive belt off the alternator pulley, but leave the belt properly mounted on the rest of the accessory pulleys on the engine.

  • 4

    Remove the two alternator mounting bolts using a wrench or ratchet and socket. Move the alternator away from the engine just enough to unplug the alternator electrical connector and wire, then lift the alternator off the engine.

  • 5

    Set the new alternator in place. Plug the alternator electrical connector and install the electrical wire. Install the two mounting bolts and torque them to 18 foot-lbs., using a torque wrench (see Tips for more information).

  • 6

    Slide the drive belt over the alternator pulley. Depending on the belt-tension system on your vehicle, either: (1) slide the belt over the idler pulley after pivoting the pulley with the breaker bar, then carefully release the tensioner; or (2) adjust the pulley locking and adjusting bolts; or (3) push the alternator away from the engine using a pry bar to provide the necessary tension to the drive belt and tighten the alternator-mounting bolts. Double-check to make sure the belt is properly seated over the pulleys ribs.

  • 7

    Connect the black, negative battery cable



  • Read more: How to Remove an Alternator on a Range Rover ' eHow.com http://www.ehow.com/how_4896539_remove-alternator-range-rover.html#ixzz17CkAleLX

    Posted on Dec 05, 2010

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    2 Answers

    2004 land rover range rover hse transmission is overheating and drives like it's in sand or mud. Also have air suspension inactive warnings along wIth HDC inactive suspension light dosent even lightup


    check that you are not in 4 x 4 settings on hard surface as that loads up the transmission making it work harder
    that it turn can over heat the transmission oil
    check for correct oil level in transmission as too much oil or not enough will also heat oil
    take it to an accredited service center that has experience on your make of vehicle for a diagnosis of all problems

    Nov 30, 2016 | BMW Cars & Trucks

    1 Answer

    How to reset timing marks after replacing a broken timing belt?


    Land Rover Freelander 2002-2005 KV6 Timming belt and ...

    ? 4:31
    https://www.youtube.com/watch?v=sz_oe9tIFH4
    Jul 3, 2011 - Uploaded by Jaime Depaula
    Land Rover Freelander 2002-2005 KV6 Timming belt andreplacing valves - Video 2 ... shops in North Eastern USA for bent valves and timing belt change? .... Land Rover 200tdiTiming Belt -From Broken Belt to Retiming the ...

    ROVER K Series Cambelt Change Video - YouTube

    ? 10:52
    https://www.youtube.com/watch?v=1Qn8ljQKZxA
    May 4, 2012 - Uploaded by metalworker007
    How to change a rover K series cam belt .. by Technozen of ...soy espa?ol porfavor quiero saber timing marks de MG ROVER 25 petrol 1795cc engen .... Hi, Have a Land Rover Freelander1999 petrol serie K, that dont start, ...

    Freelander 1.8i timing belt - Land Rover Technical Archive - LR4x4 ...

    forums.lr4x4.com > ... > Tech Archive > Land Rover Technical Archive

    Nov 20, 2006 - 1 post - ‎1 author
    The following is instructions for replacing the timing (or camshaft) belt on the 1.8i petrol engine, as fitted to a Freelander. This is the K-series ... With the timing set, thecam sprocket marks should look like this. Posted Image

    How to Replace timing belt on Land Rover Freelander 2.5 ...




    Dec 10, 2015 | 2002 Land Rover Freelander

    1 Answer

    My 2000 land rover discovery 2 sd model will not engage into 4 wheel drive and the engaging handle has no pressure at all?


    Your DII is (always) in 4 wheel drive. There is NO 2x wheel drive option on a DII, it's always in 4x4 high, or low. To select 4-wheel drive low, put your transmission in neutral and pull down the high low gear selector.

    Jul 12, 2014 | 2000 Land Rover Discovery

    1 Answer

    How do i engage into 4 Wheel Drive Mode on my V8 4.6 HSE


    a 1999 landrover Range Rover is in constant 4 wheel drive. the only change you can make is high or low range and this is handled through the gear shift selection.

    Feb 13, 2014 | 1999 Land Rover Range Rover

    1 Answer

    No 4 weel drive


    Put it neutral and then hit the button for 4 Wheel drive. It should work then and do the same to take it off 4 wheel drive.

    Jan 31, 2014 | 2003 Ford Explorer

    1 Answer

    I can't get my 95 Land Rover Discovery out of 4-wheel drive


    The vehicle is all time four wheel drive, it cannot run in two wheel drive. The second shifter is for differential lock and high/low range selection.

    Sep 28, 2011 | 1995 Land Rover Discovery

    1 Answer

    Connect four wheel drive for a freelander land rover 2005


    The Freelander, along with all Land Rovers are permanently in 4 wheel drive: You need to take the car to a workshop to see what is happening. Freelanders have big problems with the transfer box, this maybe the problem. When you reverse the car and put the car steering to full lock whilst reversing, do you feel that the car is blocking or binding, as though you have the brakes on. If so this is an indication that the transfer box is faulty. These boxes cannot be repaired, replacement only and are quite expensive.
    Hope this helps

    Jan 03, 2009 | 2004 Land Rover Discovery

    Not finding what you are looking for?

    Open Questions:

    Cars & Trucks Logo

    Related Topics:

    28 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Land Rover Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22485 Answers

    Marvin
    Marvin

    Level 3 Expert

    85239 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8984 Answers

    Are you a Land Rover Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...