Question about Buick Skylark

3 Answers

How to remove back seat in 1972 buick skylark

Posted by toms47 on

Ad

3 Answers

joseph cayo

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 192 Answers

Push down firmly on the front portion of the bottom rear seat and push it backwards until the front bottom of the seat unhooks from a latch on each side, then lift the bottom seat out. The back of the rear seat has two bolts, one on each side, that connect the seat brackets to the rear firewall. Remove the two bolts and push the back of the seat straight up until it releases and it will come out. The seat tom can often be hard to move enough to get it unlatched.

Posted on Jun 20, 2011

Ad

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 120 Answers

Pull on the seat inthe crack of the back rest and the seat after u got it forward remove the seat or unbolt the seat to remove

Posted on Jun 20, 2011

Ad

Aobd2

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Buick Master
  • 1,049 Answers

Remove the seat cushion retaining bolts, detach the seat cushion and remove it up and out from the vehicle.

Remove the rear seat back retaining bolts at the bottom of the seat back. Pull up then out to disengage the upper frame from the hangers and remove seat back from the vehicle.

Installation is the reverse of removal.

Courtesy: Haynes GM repair Manual #38025. You can probably find a copy of it on Amazon or eBay cheap

Posted on Jun 20, 2011

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the signal flasher in a 1989 buick skylark,i know where the hazard flasher is.


Here you go Tom , The Flasher is located: Front seating area, driver side, under dash, above fuse block, mounted on kick panel
Application:
Turn signal

Mar 10, 2015 | 1989 Buick Skylark

2 Answers

I need to know how to take out the bottom of the back seat in my 1998 Buick Skylark so I can install seat covers I just ordered online. I can't figure out how to fold the backrest down either. Please help!


check under the floor mat just under the seat for 2 bolts that hold it down or it may just take a sudden lift up at the front to pull it out of the spring clips holding it down. As to the back bit , when you have the seat out check for 2 bolts under the bottom of the back . remove them and lift the back straight up to unclip from the top.

Apr 21, 2014 | 1998 Buick Skylark

1 Answer

Air bag light on on a 1997 buick skylark that got floooded


find one in scrapyard and change the module and see what happens also clean the connectors under the front seats as the pins could be corroded depending on how the water was as the module should be under the centre consol so it may have been high enough to avoid the water but the connections under the seats are lower so would have got wet ,best of british with it and sypathys

Sep 07, 2011 | 1997 Buick Skylark

1 Answer

How do I install a serpentine belt on 97 buick skylark? Do I remove motor mount?


Hello
Yes remove the motor mount.You need to have it supported with a floor jack first.

Here is a step by step link to help guide you.

Good luck
http://www.wikihow.com/Change-a-Serpentine-Belt-on-a-1997-Buick-Skylark

Dec 08, 2010 | 1997 Buick Skylark

1 Answer

In order to replace the serpentine belt on a 1994 Buick Skylark It appears that something has to be removed in order to remove the belt and replace it. What exactly has to be removed?


Nothing has to be removed. Just relieve the tension on the belt and it will come off. Find the tensioner pulley and pry it back. Look for a square hold where you insert a 1/2" ratchet. If you find none look for a way to pry it back. All you have to do is relieve the tension.

May 09, 2010 | 1994 Buick Skylark

1 Answer

My power seat stopped working on my 93 buick skylark and i cant figure out how to fix it


try checking the fusebox or see if the plug connection under the seat has somehow become disconnected ot the wiring is frayed or broken

Aug 29, 2009 | 1993 Buick Skylark

1 Answer

1998 buick skylark rear brake repair diagram


Compare the setup with the way they are arranged on the opposite wheel. I always recommend doing one wheel at a time with drum brakes, that way you can always walk to the other side and see how the springs are arranged.

Mar 23, 2009 | 1998 Buick Skylark

1 Answer

1993 buick skylark serpentine belt removal


there is going to be a tensioner pulley near the front of the motor on top that you have to apply pressure to or you can loosen the alternator and take it off that way,just remember how it came off so you can put it back on

Aug 13, 2008 | 1994 Buick Skylark

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

2,475 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Joe Taylor
Joe Taylor

Level 3 Expert

2228 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14866 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...