Question about 1996 Honda Accord

2 Answers

Can I remove the relay for the ABS system and still run standard breaks ?

Posted by Anonymous on

Ad

2 Answers

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 133 Answers

There should be no problem as abs is an ad on. just make sure you completely disable it or it can kick in at the wrong time. hope this helps. goodluck

Posted on Jun 18, 2011

Ad

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Mentor:

    An expert who has written 3 tips or uploaded 2 video tips.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 122 Answers

Ya There is no Problem when u remove the ABS System.............
There will be no connection between ABS system and to u r Breaks..... :) :) :)
I hope this will help u out ............... have gr8 day .... :)

Posted on Jun 20, 2011

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

ABS and handbrake light beeps while driving

ABS warns you about a problem in your ABS System starting from the fuse, or relay and the other light is not for the hand break ! it's warning you about your break PADS.
So change your break pads and check your ABS system functionality.
0helpful
1answer

Changed battery in my 2007 Mercury Montego now brakes engage w/o applying brake petal. How do I get that to stop?

check fuses and relays ---check your abs [anti-lock braking] system a sensor or wiring connection may have been disconnected or damaged while work was being done until fixed try removing the abs fuse this will stop abs control and give you standard brakes
0helpful
2answers

My abs and brake light stay on while am driving

The computer has detected a condition that indicates a fault with the ABS/Traction system. Typically that's caused by a wheel sensor problem, but it can also be caused by a faulty connector, peripheral device or the computer.
The above is the shop or garage answear. How about telling us how to fix the problem , besides replacing the computer or wheel sensor? How do we check these things?
Sometimes can be as simple as a short circuit in the rear break lights or a faulty connection in the break lights.
You can start checking the break light system. Then the sensors and finally the computer.

Antilock Brakes
0helpful
1answer

Can the ABS system on a 04 GMC canyon be changed to standard brakes

Why not just disable the ABS? Pull the fuse or relay.
1helpful
2answers

2004 Nissan Maxima ABS pump keeps running when ignition is off

the module is bad. needs a new abs pump. to temporary remedy it find the pump and disconnect its plug. be careful as the abs now is not working ( not that it was before) and incase of full breaking car will lock and slide tires. take it to a shop to get replaced.
0helpful
1answer

I have a 1993 Jaguar xj6 the power brakes are not working. Very hard to stop like manual brakes. They worked until I pressure washed under the hood. All fuses are good best I can tell, ABS relay is good....

I would, Double check your brake fluid level first. Also;

The water from the pressure washer may have made it into 1 or more of the electrical plugs on and/or around the master cylinder. You may try carefully removing the plugs, ( be careful not to break the little plastic clips that hold them in place,) try and use a hair blow dryer to make sure there's no moisture in either end of the plug and then reconnect.

As far as the ABS, ( anti-lock breaking system ), it is a safety and secondary part of your breaking system and usually would not meet emergency statis by itself, however, with your primary breaks also having a warning light on, I absolutely would consider your break issues as an emergency.

I hope this helps.
1helpful
2answers

2001 silverado abs pump wont stop running . runs with motor off. 227000 miles

swap out abs relay with a similar known good relay it's possibly a sticking abs relay
1helpful
2answers

My abs relay motor continously runs even with the car off, and killing my battery. 95 j30 infiniti

For a short term fix unplug the ABS relay. Your ABS light will stay on, and you won't have Anti lock breaks but you will be able to start your car which is always nice.
If you actually want ABS they try replacing the ABS relay, this will probably do the trick
8helpful
2answers

2001 suburban abs motor will not turn off

The ABS relay should be located in the fuse box located on the drivers side inner fender in the engine compartment. Lift the lid and check the location diagram on the inside cover to locate the correct relay/fuse.

A related issue may be a loose ground wire. There is one located on the top rear of the engine block. It is a bolted connection. Remove this bolt, clean the surfaces and replace. This simple step has cured many electircal issues on these trucks.
Not finding what you are looking for?
1996 Honda Accord Logo

Related Topics:

225 views

Ask a Question

Usually answered in minutes!

Top Honda Experts

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8991 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6963 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15010 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...