Question about 2001 Toyota Echo

1 Answer

Changing wheel bearing on 2002 toyota echo (front)

Posted by whitebl on


1 Answer


  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 200 questions.

  • Toyota Expert
  • 276 Answers

You have to remove brake pads, rotors, struts, tie rod end and lower ball joint. whole unit comes out then. the bearing has to be pressed out and new one pressed back in good luck

Posted on Aug 26, 2018


5 Related Answers


  • 2920 Answers

SOURCE: Changing of front wheel bearing

i assume u want to both inner and outer have to pull the whell off the caliper for the brakes has to come off,there will be a center cap on the hub,,take ot off,inside there you will find a nuts with a cotter pin in it.remove it.gently pull on the hub abd iit should come off in your hands.the outer bearings will come out always remember to repack them with grease before you replace them the inner bearings will be behind the rotor and will have to be chanfed also as well as greased,you have to do this on both sides the same process.put it back together the same way you take it apart

Posted on Aug 15, 2008



SOURCE: 2000 toyota echo, wheel bearings

I found this site to be very helpful with this job:

Posted on Sep 23, 2008


  • 5158 Answers

SOURCE: change front wheel bearing

this is a pretty good guide on bearing replacement for your car

Please take a moment to rate this solution

Posted on Feb 02, 2009


Colin Stickland

  • 22485 Answers

SOURCE: 2002 ford explorer front wheel bearing assembly

remove hub ,take retaining circlip out and knock it out with a big big hammer supporting it on an old wheel rim and a tree trunk.this job is easy to do but unless you have the right tools entrust it to a garage who will have a nice press .

Posted on Feb 02, 2009


  • 24 Answers

SOURCE: how to change a rear wheel bearing on a 1994 toyota camry

The rear wheel bearing on a toyota camry is replaced by replacing the wheel bearing and hub as a unit. this is a design change as compare to older models with two piece wheel bearings. Scotch drive wheels. Remove rear wheel. Remove rear brake drum. (note: if emergency brakes are applied you will not be able to remove brake drum) Remove dust cap and hub retaining nut. Hub should slide off as unit. Replace hub with new unit. Installation is reverse of removal.

Posted on May 30, 2009

Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2003 Toyota ECHO still have humming on right front new tire/hub/bearing. (changed bearing 4 times until satisfied of proper installation) Can anyone help?

Does the vehicle have run flat tyres? As these can cause a humming drone noise?

Also, it would be worth having the vehicle “tracked” / full wheel alignment. The person doing this looks at car steering and suspensions every day and will notice if anything is out of line

Oct 16, 2018 | Toyota Cars & Trucks

1 Answer

I have a 2000 toyota Echo and in left turns the steering stops working and the car drifts or slides until i press on the brake and it regains steering control. Whats going on? This happens only occa

have the front end steering joints and suspension checked by an accredited front end specialist. Check the wheel bearings and cv joints for serviceability. Although you say it is only occasionally it is a critical issue as on any occasion it may place you or others in harms way.

Sep 10, 2014 | 2000 Toyota ECHO

1 Answer

Toyota echo 2004 replace rear wheel bearings

take off rear wheels. inside on the back there is 4 bolts let them go, and you should be able to tap out the unit with the bearings in it. I did it without removing the shoes. good luck

Nov 25, 2012 | 2004 Toyota ECHO

1 Answer

Rear wheel bearing 2002 toyota hihlander

On front wheel drive models, the rear hub bearing is an assembly that bolts to the spindle.
Not sure about AllWheelDrive models.

Jun 29, 2012 | 2002 Toyota Highlander

1 Answer

Wheel bearing on my 2000 echo

You have to remove your wheel, suspension arm and track rod from the hub then remove wheel hub. You then remove the bearing from it and fit a new one, sounds easy? It isn't. Unless you have the correct tools and equipment I advise you get a mechanic to fix this one or you could mess up the new bearing.
Tools needed: Various spanners and sockets, hammers, ball joint splitter, hydraulic press and various drifts, Puller and maybe a grinder.

Nov 17, 2011 | 2000 Toyota ECHO

1 Answer

Toyota 2002 Camry, 260,000Km, Drone begins with

sounds like bad wheel bearing, lift cars front wheels set parking brake, put car in drive, listen to each wheel to find bad baering good luck.

Oct 13, 2009 | 2002 Toyota Camry

1 Answer

Noisy Ride

sounds like a wheel bearing,ask a local mechanic to confirm

Nov 13, 2008 | 2002 Toyota ECHO

Not finding what you are looking for?
2001 Toyota Echo Logo

Related Topics:


Ask a Question

Usually answered in minutes!

Top Toyota Experts

Thomas Perkins
Thomas Perkins

Level 3 Expert

14869 Answers

Greg Bernett
Greg Bernett

Level 3 Expert

2993 Answers


Level 3 Expert

4376 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides