Just two main fuse box there, underhood and pasesnger side; additional details could find in the next link, from Service Manual: ZJ-Secc-8W-Wiring-Diagrams (page 10 for device locations).
Hope this helps (remember to rate and comment this free answer).
SOURCE: 1998 and 2000 jeep grand cherokee
This Info taken from Wikipedia, the free encyclopedia
http://en.wikipedia.org/wiki/Grand_Cherokee
Hopefully this will answer your question.
The redesigned WJ 1999 Grand Cherokee shared just 127 parts with its predecessor. The structure was stiffened by PorscheEngineering for sharper steering and lighter weight. The spare tire wasrelocated from the side of the cargo compartment to under the floor togreat relief of owners. The two heavy pushrod V8 engines were replaced by chrysler's first clean sheet V8 since the 60's (SOHC aluminium heads, plastic intake), Chrysler's then-new PowerTech. Although this engine produced less torquethan both previous V8s, it was lighter and got much better fuel economyand provided similar on road performance figures (the 23 gallon fueltank was replaced with one of a 20.5 gallon capacity). The Inline 6engine was also updated in 1999. 10 horsepower (7.5 kW) was added byredesigning the intake manifold. The manual transmission was dropped with this model.
While other Jeep vehicles used the Mopar 5 x 4.5 bolt circle, thiswas the first Jeep following the 1987 Chrysler buyout to receive awider bolt pattern — 5 x 5. The 5 x 5 bolt pattern (also 5 x 127 mm),although common to GM rear wheel drive vehicles and light dutytrucks/vans, has spread beyond its use with GM (and Ford with their 1973 to 1978 LTDs and Lincolns). Chrysler first used the 5 x 5 pattern on full-size half-ton Dodge Ram pickups and Dodge Ramcharger SUVs in 1986.
A notable feature available in this generation was the automatic four wheel drive option called Quadra-Drive II.With three viscous clutches, it was one of only a few four wheel drivesystems at the time with triple locking differentals, joining thecontemporary Mercedes Gelandewagen, Mercedes Unimog and Magna SteyrPinzgauer, and the only one of the four with fully automatic operation,although the axle differentials could not be manually locked like inthe other three vehicles.
The 45RFE and 545RFE automatic transmission in the WJ was notable. It included three planetary gearsets rather than the two normally used in a four-speed automatic. Thisgave it six theoretical speeds, and it would have been the firstsix-speed transmission ever produced in volume, but it was programmedto only use five of these ratios. Four were used for upshifts, with adifferent second gear for downshifts. Although five of the six ratioswere used, Chrysler decided to call it a "4-speed automatic". In 2001,the programming was changed to make use of all six ratios. Rather thanhave six forward gears, the transmission was programmed to act as afive-speed with the alternate second gear for downshifts. The RPM at70 miles per hour (110 km/h) on a 545RFE is 2000 rpm, 200 rpm less thanthe 45RFE programming. 1999 and 2000 model year WJ owners can havetheir 45RFE transmission's programming flashed to enable the extra gearas both transmissions are physically the same. The 42RE 4-speedautomatic remained the transmission for the Inline 6 engine. It was notchanged from the previous model Grand Cherokee's.
SOURCE: 98 jeep grand cherokee won't disengage from 4x4
check the vaccume module on the front axel it my have come un pluged or the electric connector hope this helps
SOURCE: fuse box diagram for 1995 jeep grand cherokee laredo
look on the net that is where i got mine
SOURCE: fuse box diagram for 1995 jeep grand cherokee 6
EMAIL ME I CAN CAN EMAIL YOU THE LAYOUT
[email protected]
SOURCE: 98 grand cherokee asd relay blowing fuse
The fuse it doing it's job, you have a short ( Wire that is connected to a ground, that draws too much power )
If you have an electrical schematic ( Repair manual ) find out which wires are connected to that fuse and check them for any chaffing, cuts, unnesassary twists, or corrosion.
If you have a ohm-meter, isolate the system ( by disconnecting the fuse, and other connections. Then check for any resistance on wires that should not be connected ( because you disconnected them ) by having one Lead on the wire's connector and the other meter-lead on your car's frame. A good wire will not have continuity if it is isolated.
999 views
Usually answered in minutes!
×