I have a Mercedes CLK 430 and the radio, cd, nav comes on but I do not hear anything. Occasionally I hear some 'crackling' from the speakers even though I've turned off the radio. It use to just work in the morning but not the rest of the day. Now it doesn't work at all. So radio comes on but no volume. Any ideas?

SOURCE: top will not close clk 430 mercedes benz

did you recently have a dead battery? Either way try to resynchronize your windows (i'm not sure if you meant front window or rear quarter window). If you hold the window switch in the up position(car running and door closed) untill window reaches the top and continue to hold for 10 seconds the window will reprogram itself. try both front windows. This system is complicated and is best diagnosed via s.d.s. diagnostic machine. I will give you a couple of other possible easy remedies. If your vehicle is equiped with a ski window in the rear trunk panal the door must be shut, also your cargo cover must be shut and plastic lid secured. There are numerous micro switches that input to your soft top control unit-any one could cause the top to be inop. Check to make sure the switch on the cargo cover( retractable cover in trunk) is secured to it's housing, they do periodically fall off. Also if your roll bar ( rear head rests ) has been mechanically deployed You must hold the switch in the up position untill the rams lock back into the roll bar-does the roll bar operate? Always operate top with vehicle running because they are very voltage dependent. Your owners manual will explain how to manually raise top and some simple operation and repair remedies. If you are knowledgable about automotive electrical systems you can disconnect both leads from the battery and touch them together to drain the capacitors and it may reset the module( do not attempt if you are not knowledgable with automotive electricity because there are many things that can go wrong. hopefully I have been helpful.

SOURCE: on my 2000 clk 430 mercedes the blower motor is

Sir,
It can be fuse but you are also to check if the it motor of blower has have not burned or had any broken wire.

SOURCE: need a radio code for a mercedes benz clk 430 2001

You can get the code from any Mercedes dealer around you. Or you can have the code by taking the radio out and take the serial to a radio repair shop and they can get the code from the serial.

mx5turbo92

• 545 Answers
• Posted on Dec 17, 2009

SOURCE: i need the mercedes benz 1999 clk 430 radio code

AR82.60-P-7502-01A Coding Radio
(MODEL all with CODE (750) Radio Becker Europa 2000 with CODE (751) Radio Becker Grand Prix 2000 with RDS)

1. If the radio is disconnected from the power supply, it is not operational when re-connected. After switching on the ignition and the radio, the readout CODE appears in the display.
2. The code number for the radio is advised to you on the enclosed CODE CARD.
3. To enter the first digit of the code number, you have to continue pressing station button 1 until the correct digit appears in the display. Adopt the same procedure for the second, third and fourth digits.
4. Once you have entered the correct code number with the station buttons 1, 2, 3, 4 and confirmed the entry with the SEEK button (press down), the readout CODE disappears. The radio can now be operated.
5. If you enter a wrong code three times, you must wait 15 minutes before making a new entry. In addition, if 9 incorrect entries are made, the radio will then not operate for 24 hours. During this time the radio and the ignition (terminal 15) must remain switched on.

1. If the radio is disconnected from the power supply, it cannot be operated by simply reconnecting. After switching on the ignition and the radio the word "CODE" appears in the display on the radio.
2. The code number for the radio is given on the enclosed CODE CARD.
3. Enter the code number with the station button, e.g. number 1, station button 1. After entering the first number the word "CODE" disappears and the number entered appears followed by 4 dashes. The next character to be entered flashes. After entering all five numbers, the first character starts flashing again. In this state the code number can be written over as frequently as desired. A correction can be made only by entering the complete code number again.
4. Confirm code number: Press TUNE, AUTO/SEEK or SC button. The radio automatically switches on and indicates the radio station or frequency stored with station button 1.
5. If an incorrect code number is entered and confirmed, the word "CODE" appears again on the display. If an incorrect code is entered three times the word "WAIT" appears on the display and the radio locks up for approx. 10 min. If the code is entered incorrectly three times again the radio locks up again for 10 min. Three more incorrect entries (a total of 9 incorrect attempts) increase the lock-up time to 60 min. Another three incorrect entries lock up the radio for another 60 min. The waiting time runs only when the radio is switched on.

SOURCE: how do I reset the service indicator on the

NOTE: These instructions apply to vehicles that are currently due a scheduled service. Manual resetting of the service interval indicator may not be possible if the time or distance covered is outside the programmed parameters of the vehicle. In this case, it may be necessary to use manufacturer's or equivalent diagnostic equipment.
Switch ignition ON and immediately press button [A] twice 42039. Switch ignition OFF. Press and hold button [A] while switching ignition ON. After 10 seconds the new interval will appear in the display accompanied by a beep. Release button [A]. Switch ignition OFF.

BUTTON A is trip reset.