Question about 1985 Toyota Land Cruiser

1 Answer

Hj75 2h engine injector pump removal and install

I would like pages from workshop manual to perform this procedure

Posted by jjboyd786 on

  • Anonymous Sep 07, 2008

    I have a 80 series 1994 1HZ landcruiser and am trying to remove the injector pump but to no avail.  Any suggestions???



×

Ad

1 Answer

Anonymous

DONT IF YOU HAVE TO RESORT IN ASKING

Posted on Sep 12, 2008

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to fit an injector pump on a pajero 2.8.so my question is how do i time the pump


if it is common rail , there is no timing requirement
if it is an inline or rotary pump , the procedure is in the workshop manual

Oct 01, 2018 | Mitsubishi Pajero Cars & Trucks

1 Answer

How to remove replace and time. A geared injector pump. On a 1999 Chrysler voyager VM system 2.5 TD four cylinder Diesel Motori Engine. Right hand drive.UK.


too long to explain here
buy a workshop manual that has all the details and photos and follow the procedure stated
better still have an accredited pump specialist shop do the job

Oct 29, 2016 | 1999 Plymouth Voyager

1 Answer

To fit diesel pump and start up


need more details as to engine make and model
this really a job for a diesel specialist shop as the timing is critical to engine performance
get a workshop manual for the vehicle and study the procedure

Oct 19, 2015 | Cars & Trucks

1 Answer

What can the fault be if there comes a black smoke out of the exhaust of your 2008 1.4tdci ford ikon


Hi, depends what colour black smoke, is it bluey black, grey black, whitey black, You may have to take it to a Diesel fuel shop, It may be the timing on the engine or the injector pump, (the pump may need to be timed to the engine, also the Injector pump also may need calibrating.) To calibrate pump you need to take it to a Diesel Fuel Workshop. Due to wear and conditions the injectore nozzles, injector pump, timing and performance of the engine will change over time.

Jan 29, 2015 | Ford Cars & Trucks

1 Answer

How to install a fuel injector on a 2002 jeep liberty 3.7


so that mean the old one is all ready removed.?
or did you mean all steps in the fsm for INJECTOR.
the steps are the same on all EFI fuel rail injectors.
you could google that or you tube it or read the FSM.

hide call keys from step 2 on, or very bad things can happen.
(wife or kids no aware of danger)
ill just cover the (basics)
1: per FSM , depressurize the system, in can be at 60PSI
parked. so avoid fuel in eyes, or a fire. we do that first.
gain access to rail under failure. (RUF) (no barking)
2: remove injector X , wire plug. (failing)
3: then detach the injector rail clamps the both rails off as one....
injector are all now loose, to pull off.
4: add new seals to new injector, and install in reverse order.

that's it, only the gain access , varies,... mostly.

last depressure steps:
run engine,
remove fuel pump relay, engine stalls. key off, hide keys
!

next tje FSM words (just the OFF section)

  1. Remove fuel tank filler tube cap.
  2. Perform Fuel System Pressure Release Procedure.
  3. Remove negative battery cable at battery.
  4. Remove air duct at throttle body air box.
  5. Remove air box at throttle body.
  6. Disconnect fuel line latch clip and fuel line at fuel rail. A special tool will be necessary for fuel line disconnection.
  7. Remove necessary vacuum lines at throttle body.
  8. Disconnect electrical connectors at all 6 fuel injectors. Push red colored slider away from injector. While pushing slider, depress tab and remove connector from injector. The factory fuel injection wiring harness is numerically tagged (INJ 1, INJ 2, etc.) for injector position identification. If harness is not tagged, note wiring location before removal.
  9. Disconnect electrical connectors at throttle body sensors.
  10. Remove 6 ignition coils.
  11. Remove 4 fuel rail mounting bolts.
  12. Gently rock and pull left side of fuel rail until fuel injectors just start to clear machined holes in cylinder head. Gently rock and pull right side of rail until injectors just start to clear cylinder head holes. Repeat this procedure (left/right) until all injectors have cleared cylinder head holes.
  13. Remove fuel rail (with injectors attached) from engine.
end expert.

alldata.com
login and read all steps. that be best , then ask questions?

Jan 02, 2012 | 2002 Jeep Liberty

1 Answer

I need a video or information on how to get the altenator in and out of a 2005 motana 3.4. I have the belt off and got it loose but cannot get it out


Hi, do you have the power steering pump off? Procedure says to take the pump off and move it aside (do not disconnect the lines). It also says to rotate the engine forward. I'm not sure that is necessary, but it may be. See procedure pasted below. Please let me know if you have more questions, and thanks for using FixYa.


Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Negative battery cable Wiper system module cover Fuel injector sight shield
  3. Rotate the engine forward.
  4. Remove or disconnect the following:
    NOTE Do not disconnect the power steering pipes from the pump


    Alternator terminal nut, lead and electrical connector Serpentine belt Front bolts and two rear bolts Alternator from the bracket Serpentine belt tensioner Bracket Power steering pipes from the retainer Fuel pressure test port cap from the injector rail


    Power steering pump and reposition it to gain access to the alternator Alternator

To install:
  1. Install or connect the following:

    Alternator Power steering pump. Torque the bolts to 25 ft. lbs. (34 Nm). Fuel pressure test port cap to the fuel rail Power steering pipes to the retainer. Torque the fastener to 54 inch lbs. (6 Nm). Alternator bracket. Torque the bolt to 37 ft. lbs. (50 Nm). Serpentine belt tensioner Alternator to the bracket. Torque the bolts to 37 ft. lbs. (50 Nm). Serpentine belt Alternator electrical connector, lead and nut. Torque the nut to 115 inch lbs. (13 Nm).
  2. Rotate the engine to its original position.
  3. Install or connect the following:

    Fuel injector sight shield. Torque the nut to 54 inch lbs. (6 Nm). Wiper system module cover Negative battery cable
  4. Perform a charging system test and verify the proper operation of the system.

Apr 02, 2011 | Pontiac Montana Cars & Trucks

2 Answers

REMOVAL OF WATER PUMP ON 95 MERCURY VILLAGER


go here too http://autos.groups.yahoo.com/group/villagerquest/ Section 03-01: Engine 1996 Villager Workshop Manual IN-VEHICLE SERVICE -------------------------------------------------------------------------------- Water Pump Removal Water Pump Removal Drain the cooling system. Refer to Section 03-03 for the procedure. Disconnect the battery ground cable (14301). Remove the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the removal procedures. Raise and support the vehicle. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley (8509) while removing the four water pump pulley bolts. Remove the water pump pulley from the water pump (8501). Remove the crankshaft pulley (6312). Refer to the procedure in this section. Remove the five lower engine front cover bolts and the lower engine front cover (6019). NOTE: Make a note of the location of the one water pump stud/bolt for ease of installation. Remove the six water pump bolts. Remove the water pump. Installation NOTE: Ensure the mating surfaces between the water pump and the cylinder block (6010) are cleaned of any sealant material. Install a continuous 2.0-3.0mm (0.079-0.118 inch) wide bead of Gasket Maker E2AZ-19562-B or equivalent meeting Ford specification WSK-M2G348-A5, on the water pump and position the water pump on the cylinder block. NOTE: Refer to the note made during removal for the location of the stud/bolt. Install the six water pump bolts. Tighten the water pump bolts to 16-21 Nm (12-15 lb-ft). Position the water pump pulley on the water pump and install the four water pump pulley bolts. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley, and tighten the four water pump pulley bolts to 16-21 Nm (12-15 lb-ft). Install the lower engine front cover and the five lower engine front cover bolts. Tighten the five lower engine front cover bolts to 3-5 Nm (27-44 lb-in). Install the crankshaft pulley. Refer to the procedure in this section. Lower the vehicle. Install and adjust the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the installation and adjustment procedures. Connect the battery ground cable. Fill the cooling system. Refer to Section 03-03 for the procedure. Start the engine (6007) and check for leaks.

Jun 06, 2009 | 1995 Mercury Villager

1 Answer

Im putting in the boss performance module


please rate as problem solved if this is what you need.



Section 03-14: Engine Controls, Electronic 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Intake Air Temperature (IAT) Sensor Removal and Installation
  1. Disconnect battery ground cable (14301) .
  1. Disconnect engine control sensor wiring (12A581) from intake air temperature sensor (IAT sensor) (12A697) .
  1. Remove intake air temperature sensor from air cleaner outlet tube (9B659). (This is the tube that goes from the air cleaner to the engine.)
  1. To install, reverse Removal procedure. Tighten intake air temperature sensor securely.
--------------------------------------------------------------------------

Jun 02, 2009 | 1994 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,383 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...