Question about 2006 Kia Sorento

1 Answer

I have an 05 Sorento which I am replacing the timing belt and water pump. I did not have to remove the crankshaft and used 1/4" x 2 1/2" bolts with washers to hold the cam sprockets in place. I need to know with this procedure because nothing has moved is it necessary to redo the timing marks or can you slip the one belt off and the other on...

Posted by wpr686 on

Ad

1 Answer

Steve Macqueen

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Expert
  • 53 Answers

When i was working at an AUDI dealer, they way MYSELF did it was to use whiteout and make dots on the teeth of the belt and the gears before you pull the old one off. then transfer the marks by counting the teeth to know which marks go where and install new belt. if nothing has moved you should be fine. I dont think the sorento has an "interference" head, meaning if you mess up the marks by a tooth or so, you wont do any real engine damage. for future reference i suggest my whiteout technique!! I have an 05 Sorento - racecarsteve.jpg

Posted on May 12, 2011

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change a waterpump on a 2001Volkswagen cabrio?


Your Cabrio has one of several 2.0L Volkswagen engines - determine your engine type from the
8th digit of your VIN, which will be either an "A", or "C",both are 2.0L engines.

Volkswagen 2.0L engines offered in 2001:
(a) 2.0L (Aba) Engine
(b) 2.0L (Aeg/Avh/Azg/Bdc/Bev/Bgd) Engine
(c) 2.0L (Aeg/Avh/Azg/Bdf) Engine

For completeness, I've included the water pump maintenance manual entries for all (3) 2.0L VW
engines offered in 2001. Note that the instructions below include (3) illustrations, which are
reproduced faithfully from the manual, but the last (2) illustrations are identical, since the last two
engines in the list above are virtually identical.

Volkswagen 2001 engines - water pump replacement

2.0L (Aba) Engine

Before servicing the vehicle, refer to the Precautions section.

Remove or disconnect:

1. Coolant

2. Thermostat housing from under the water pump housing.


Loosen but don't remove the bolts holding the pulley to the water pump.

Remove or disconnect:

Timing belt cover.

Alternator and/or steering pump as required to remove the water pump drive belt.

Water pump pulley. On some vehicles, the crankshaft pulley must also be removed by removing the bolts holding the pulley to the timing belt sprocket.

Water pump from its housing.


To install:


Be sure to clean the housing before installing the new gasket. Install the pump into the housing. Pump-to-housing bolts: 84 inch lbs. (10 Nm).

Install the water pump drive pulley. Bolts: 15 ft. lbs. (20 Nm). Install crankshaft drive pulley. Bolts: 15 ft. lbs. (20 Nm).

Adjust drive belt tension and install the thermostat and housing. Bolts: 84 inch lbs. (10 Nm).



archaeology_93.jpg

Fig. Water pump and thermostat housing-2.0L (ABA) engine

1. Before servicing the vehicle, refer to the Precautions Section.

2. Remove or disconnect:

Coolant

Thermostat housing from under the water pump housing.



3. Loosen but don't remove the bolts holding the pulley to the water pump.

4. Remove or disconnect:

Timing belt cover.

Alternator and/or steering pump as required to remove the water pump drive belt.

Water pump pulley. On some vehicles, the crankshaft pulley must also be removed by removing the bolts holding the pulley to the timing belt sprocket.

Water pump from its housing. Refer to figure of ABA engine's water pump above.

To install:

1. Be sure to clean the housing before installing the new gasket. Install the pump into the housing. Pump-to-housing bolts: 84 inch lbs. (10 Nm).

2. Install the water pump drive pulley. Bolts: 15 ft. lbs. (20 Nm). Install crankshaft drive pulley. Bolts: 15 ft. lbs. (20 Nm).

3. Adjust drive belt tension and install the thermostat and housing. Bolts: 84 inch lbs. (10 Nm).



2.0L (Aeg/Avh/Azg/Bdc/Bev/Bgd) Engine


1. Before servicing the vehicle, refer to the Precautions Section.

2. Remove or disconnect:

Negative battery cable.

Coolant.

Accessory drive belt and tensioner.

Upper and center timing belt covers.



3. Position the engine so that the No. 1 cylinder is at TDC.
WARNING
Cover the timing belt to protect it from being contaminated with coolant.


4. Loosen the timing belt tension and slide the belt off the water pump sprocket.

5. Remove or disconnect:

Timing belt guard (2) mounting bolt (1), if equipped.

Water pump mounting bolts (5), then the water pump (4).

O-ring (3) and clean the seating area.


To install:



archaeology_94.jpg



Fig. Exploded view of the water pump mounting-2.0L (AEG/AVH/AZG/BDF) engine

1. Install or connect:

O-ring, moistened with coolant.

Water pump so that the plug in the housing faces downward. Mounting bolts: 11 ft. lbs. (15 Nm).

Timing belt guard, if equipped. Mounting bolt: 15 ft. lbs. (20 Nm).

Timing belt.

Upper and center timing belt covers.

Accessory drive belt tensioner. Mounting bolt: 18 ft. lbs. (25 Nm).

Accessory drive belt.

Coolant.

Negative battery cable.



2. Check and clear any DTCs, then match the ECM to the TCM.


2.0L (Aeg/Avh/Azg/Bdf) Engine


1. Before servicing the vehicle, refer to the Precautions section.

2. Remove or disconnect:
1. Negative battery cable.

2. Coolant.

3. Accessory drive belt and tensioner.

4. Upper and center timing belt covers.


3. Position the engine so that the No. 1 cylinder is at TDC.

WARNING
Cover the timing belt to protect it from being contaminated with coolant.

Loosen the timing belt tension and slide the belt off the water pump sprocket.

Remove or disconnect:

1. Timing belt guard (2) mounting bolt (1).

2. Water pump mounting bolts (5), then the water pump (4).

3. O-ring (3) and clean the seating area.


To install:



archaeology_95.jpg


Fig. Exploded view of the water pump mounting-2.0L (AEG/AVH/AZG/BDF) engine


Install or connect:

1. O-ring, moistened with coolant.

2. Water pump so that the plug in the housing faces downward. Mounting bolts: 11 ft. lbs. (15 Nm).

3. Timing belt guard. Mounting bolt: 15 ft. lbs. (20 Nm).

4. Timing belt.

5. Upper and center timing belt covers.

6. Accessory drive belt tensioner. Mounting bolt: 18 ft. lbs. (25 Nm).

7. Accessory drive belt.

8. Coolant.

9. Negative battery cable.


Check and clear any DTCs, then match the ECM to the TCM.

Sep 13, 2011 | 2001 Volkswagen Cabrio

2 Answers

I have no clue on how to replace water pump on a 1995 chrysler cirrus 2.5L. I have to do this myself I dont have the money for a garage.


This is found on the autozone.com website.

2.5L Engine
See Figures 3 through 7
  1. Disconnect the negative battery cable.
  2. Place a large drain pan under the radiator drain plug. Drain and properly contain the engine coolant.

This procedure requires removing the engine timing belt and the auto tensioner. To help assure proper alignment at assembly, it may be helpful to set the engine at TDC on No. 1 compression stroke. This should align all timing marks on the crankshaft sprocket and both camshaft sprockets.
  1. Remove the accessory drive belts and crankshaft damper.
  2. Remove the right engine mount. This requires safely supporting the engine with a floor jack and wood block so the mount can be removed.
  3. Remove the timing belt covers.
  4. Remove the timing belt and tensioner.



0900c152800896a7.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Remove the water pump mounting bolts


0900c152800896a8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 4: Pull the water pump assembly off of the engine and inlet pipe


0900c152800896a9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 5: Open the water pump housing and examine for cracks or damage


0900c152800896aa.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 6: Replace the water pump housing gasket using a scraper tool


0900c152800896ab.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 7: Always keep the water pump's mounting bolts lined up with their correct mounting holes

  1. Remove the water pump mounting bolts.
  2. Separate the water pump from the water inlet pipe and remove the pump.

To install:
  1. Thoroughly clean all sealing surfaces. Inspect the pump for damage or cracks, signs of coolant leakage at the vent, and excessive looseness or rough turning bearings. Any problems require a new pump.
  2. Install a new O-ring on the water inlet pipe. Wet the O-ring with water to make installation easier. DO NOT use oil or grease on the O-ring.
  3. Install a new gasket on the water pump and fit the pump inlet opening over the water pipe. Press the assembly together to force the pipe into the water pump.
  4. Install the water pump-to-engine bolts and tighten to 20 ft. lbs. (27 Nm).
  5. Install the timing belt and timing belt tensioner. Set the timing belt tension.
  6. Install the timing belt covers. Install the right engine mount. Remove the floor jack and engine block from underneath the engine.
  7. Install the crankshaft damper.
  8. Install the accessory drive belts and set to the proper tension.
  9. Connect the negative battery cable.
  10. Fill and bleed the engine cooling system.
  11. Start the engine and verify proper operation, with no leaks

Aug 20, 2011 | 1995 Chrysler Cirrus

2 Answers

Timing belt


TIMING BELT & SPROCKETS R & I
NOTE: Some procedures may differ slightly due to engine
construction.
Removal
1) Remove all necessary air ducts. Position No. 4 piston at
TDC of compression stroke. Align timing marks. See Fig. 2. Remove fan
and fan shroud. Remove belts. If necessary, remove radiator and
splashguard.
2) Prevent engine from rotating and remove crankshaft timing
pulley retaining bolt. Remove upper and lower timing belt covers.
Remove spring from tension pulley. Loosen adjusting bolt and move
pulley toward water pump. Remove timing belt.
CAUTION: Ensure pistons are at TDC when rotating camshaft or damage
may result.
Inspection
1) Handle timing belt carefully. Avoid twisting or kinking
belt. Do not allow belt to become contaminated by water, oil, dirt or
other contaminates. Inspect belt for cracks or damage. If necessary,
replace.
2) Measure tension pulley spring length and force. Spring
length should not exceed 2.76" (70.2 mm) and spring force should not
be less than 197-347 lbs. (27-48 kg).
3) Replace tension pulley spring if not within specification.
Installation
1) Pull tensioner fully toward water pump side and
temporarily tighten retaining bolt. Ensure No. 4 cylinder is at TDC on
compression stroke by rotating crankshaft until keyway aligns with
mark on front crankshaft seal housing (12 o'clock). Rotate camshaft
until timing mark on cam gear (arrow) aligns with mark on upper
camshaft cover (notch). See Fig. 2.
NOTE: When timing marks are aligned as stated above, No. 4 piston
is at TDC on compression stroke.
2) Position timing belt over crankshaft sprocket, oil pump
sprocket, camshaft sprocket and tensioner in that order. Ensure belt
is positioned in sequence given and without slack between sprockets.
Loosen tension sprocket adjusting bolt allowing spring tension to
tighten belt. Tighten adjusting bolt temporarily.
3) Temporarily install crankshaft pulley bolt and rotate
crankshaft 2 complete revolutions in opposite direction of engine
rotation, until marks on crankshaft and front oil seal retainer are
aligned again. See Fig. 2. Loosen tensioner lock bolt, allowing
tesioner spring to fully adjust tension. Tighten tensioner lock bolt.
4) Install timing belt covers. To complete installation,
reverse removal procedures. Tighten all bolts to specification. See
TORQUE SPECIFICATIONS table at end of this article.
Fig. 2: 2.3L & 2.6L Timing Alignment Marks
Courtesy of Isuzu Motor Co

Dec 13, 2010 | 1989 Isuzu Pickup 2WD

1 Answer

Ifailed to get on tdc before removing old timing belt how do I get back in time so Icanreplacebelt.


This is the complete procedure from the service manual on how to replace the timing belt start to finish, start over to assure u get it right, if u mess up the engine will be damaged

Removal for 1.6L engines : ONLY 2006 to 2009 CARS


Engine removal is not required for this procedure.

1.Remove the engine cover.

2.Remove the RH front wheel.

3.Remove the 2 bolts and RH side cover.

4.Temporarily loosen the water pump pulley bolts.

5.Remove the alternator drive belt

6.Remove the air conditioner compressor drive belt

7.Remove the power steering pump drive belt

8.Remove the 4 bolts and water pump pulley.

9.Remove the 4 bolts and
timing belt2_bing.gif upper cover

10.Turn the crankshaft pulley, and align its groove with timing mark "T" of the timing belt cover. Check that the timing mark of camshaft sprocket is aligned with the timing mark of cylinder head cover. (No.1 cylinder compression TDC position)

11.Remove the crankshaft pulley bolt and crankshaft pulley

12.Remove the crankshaft flange

13.Remove the 4 bolts and timing belt lower cover

14.Remove the timing belt tensioner and timing belt.

15.Remove the bolt and timing belt idler

16.Remove the crankshaft sprocket

17.Remove the cylinder head cover.

(1)Remove the wire harness bracket

(2)Remove the ignition coil.

(3)Remove the PCV (Positive Crankcase Ventilation) hose and the breather hose from the cylinder head cover

(4)Remove the engine cover bracket

(5)Loosen the cylinder head cover bolts and then remove the cover and gasket.

18.Remove the camshaft sprocket.

Hold the portion of the camshaft with a hexagonal wrench, and remove the bolt with a wrench and remove the camshaft sprocket.

INSTALLATION:

1.Install the camshaft sprocket and tighten the bolt to the specified torque.

(1)Temporarily install the camshaft sprocket bolt

(2)Hold the portion of the camshaft with a hexagonal wrench, and tighten the bolt with a wrench
Tightening torque :78.5 ~ 98.1N.m (8.0 ~ 10.0kgf.m, 57.9 ~ 72.3lb-ft)



2.Install the cylinder head cover.

(1)Install the cylinder head cover and bolts
Tightening torque :7.8 ~ 9.8N.m (0.8 ~ 1.0kgf.m, 5.8 ~ 7.2lb-ft)

(2)Install the engine cover bracket

(3)Install the PCV(Positive Crankcase Ventilation) hose and breather hose to the cylinder head cover.

(4)Install the ignition coil.

3.Install the crankshaft sprocket

4.Align the timing marks of the camshaft sprocket and crankshaft sprocket with the No.1 piston placed at top dead center and its compression stroke.

5.Install the idler pulley and tighten the bolt to the specified torque.

Tightening torque :42.2 ~ 53.9N.m (4.3 ~ 5.5kgf.m, 31.1 ~ 39.8lb-ft)

6.Temporarily install the timing belt tensioner

7.Install the belt so as not give slack at each center of shaft. Use the following order when installing timing belt.
Crankshaft sprocket →idler pulley →camshaft sprocket →timing belt tensioner

8.Adjust the timing belt tension.

(1)Loosen the tensioner pulley mounting bolt and apply tension to the timing belt.

(2)After checking the alignment between each sprocket and each timing belt tooth, tighten the mounting bolt and one by one.

Tightening torque :19.6 ~ 26.5N.m (2.0 ~ 2.7kgf.m, 14.5 ~ 19.5lb-ft)

(3)Then recheck the belt tension.
Verify that when the tensioner and the tension side of the timing belt are pushed in horizontally with a moderate force [approx. 49N (11lb)], the timing belt cog end is aprox. 1/2 of the tensioner mounting bolt head radius (across flats) away from the bolt head center.

4)Timing belt tension measuring procedure
(by a sonic tension guage)
Rotate crankshaft in clockwise direction to set 1st piston on top dead center (TDC) and rotate crankshaft in counterclockwise to 90° then measure the belt tension in the middle of tension side span (in arrow direction of above illustration) by free vibration method.


9.Turn the crankshaft two turns in the operating direction (clockwise) and realign crankshaft sprocket and camshaft sprocket timing mark.


10.Install the timing belt lower cover with 5bolts

Tightening torque :7.8 ~ 9.8N.m (0.8 ~ 1.0kgf.m, 5.8 ~ 7.2lb-ft)

11.Install the flange and crankshaft pulley, and then tighten crankshaft pulley bolt. Make sure that crankshaft sprocket pin fits the small hole in the pulley.

Tightening torque :137.3 ~ 147.1N.m (14.0 ~ 15.0kgf.m, 101.3 ~ 108.5lb-ft)

12.Install the timing belt upper cover with 4 bolts.

Tightening torque :7.8 ~ 9.8N.m (0.8 ~ 1.0kgf.m, 5.8 ~ 7.2lb-ft)

13.Install the water pump pulley and 4 bolts.

14.Install the power steering pump drive belt

15.Install the air conditioner compressor drive belt

16.Install the alternator drive belt

17.Install the RH side cover with 2 bolts

18.Install the RH front wheel.


Tightening torque :88.3 ~ 98.1N.m (9.0 ~ 10.0kgf.m, 65.1 ~ 72.3lb-ft)

19.Install the engine cover with bolts.


Tightening torque :3.9 ~ 5.9N.m (0.4 ~ 0.6kgf.m, 2.9 ~ 4.3lb-ft)

May 20, 2010 | 2006 Kia Sorento

1 Answer

How do I change a water pump on a 2004 kia sorento?


Kia Sorento 2003-05
Water Pump - Removal & Installation
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Drain the cooling system.
  3. Disconnect the negative battery cable.
  4. Remove the drive belt and the water pump pulley.
  5. Remove the timing belt cover, timing belt, auto tensioner and idler pulley.
  6. Remove the water outlet fitting, the thermostat case and the water pump fitting.
  7. Remove the water pump mounting bolts.
  8. Remove the water pump.

  9. dc45c19.jpg

    Fig. Water pump and timing belt assembly-exploded view

To install:

1016213.jpg

Fig. Water pump bolt locations
  1. Clean the gasket surfaces of the water pump body and the cylinder block.
  2. Install the new water pump gasket and pump assembly. Tighten the bolts to 12-16 ft. lbs. (17-22 Nm).
  3. Install the water pump fitting, the thermostat case and the water outlet fitting.
  4. Install the auto tensioner and timing belt. Adjust the timing belt tension, then install the timing belt cover.
  5. Install the drive belt, water pump pulley and then adjust the auto tensioner.
  6. Refill the coolant.
  7. Run the engine and check for leaks.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Disconnect the negative battery cable.
  4. Remove the drive belt and the water pump pulley.
  5. Remove the timing belt cover, timing belt, auto tensioner and idler pulley.
  6. Remove the water outlet fitting, the thermostat case and the water pump fitting.
  7. Remove the water pump mounting bolts.
  8. Remove the water pump.

To install:


e9be8c3.jpg

Fig. Water pump bolt locations

596080e.jpg

Fig. Water pump O-ring installation
  1. Clean the gasket surfaces of the water pump body and the cylinder block.
  2. Install the new water pump gasket and pump assembly. Tighten the bolts to 12-16 ft. lbs. (17-22 Nm).
  3. Install the water pump fitting, the thermostat case and the water outlet fitting.
  4. Install the auto tensioner and timing belt. Adjust the timing belt tension, then install the timing belt cover.
  5. Install the drive belt, water pump pulley and then adjust the auto tensioner.
  6. To adjust the drive belt tension, hang the belt on the pulley of the tensioner and install the tensioner.
    NOTE If the tensioner is already installed, loosen its mounting bolts to allow belt installation
  7. Install the drive belt.
  8. Adjust the belt tension to specification by turning the adjusting bolt clockwise or counterclockwise.
  9. Air conditioning belt tension should be 0.28-0.039 inch. Alternator belt tension should be 0.39-0.051 inch. Power steering belt tension should be 0.31-0.051 inch.
  10. Torque the tensioner assembly bolt to 33-36 ft. lbs. (45-50 Nm).
  11. Refill the coolant.
  12. Run the engine and check for leaks.

TY for using Fixya; remember comment and rated this.

Apr 01, 2010 | 2004 Kia Sorento

1 Answer

Replacing the timing belt on a 1998 Nissan Quest and need to know cam shaft and crank shaft positions.


go here for expert help on Villager & Quest

http://groups.yahoo.com/group/villagerquest/

e09cf57.gif

Item Part Number Description 1 — 40 Timing Chain/Belt Teeth 2 6256 Camshaft Sprocket , Front 3 — 43 Timing Chain/Belt Teeth 4 6306 Crankshaft Sprocket 5 6268 Timing Chain/Belt 6 6256 Camshaft Sprocket , Rear
Removal
  1. Drain the cooling system. Refer to Section 03-03 for the procedure.
  1. Disconnect the battery ground cable (14301) .
  1. Remove the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the removal procedure.
  1. If equipped, remove the three A/C compressor drive belt idler pulley bolts and the A/C compressor drive belt idler pulley.
  1. Remove the upper radiator hose bracket bolt.
  1. Loosen the two upper radiator hose clamps and remove the radiator hose bracket bolt. Remove the upper radiator hose (8260) and the upper radiator hose bracket from the vehicle.
  1. Remove the water bypass hose (8597) from between the thermostat housing and the water hose connection (8592) .
  1. Remove the main wiring harness from the upper engine front cover (6019) .
  1. Remove the eight upper engine front cover bolts and the upper engine front cover .
  1. Raise and support the vehicle.
  1. Remove the RH front wheel and tire assembly.
  1. Remove the four RH outer engine and transmission splash shield bolts and two screws and remove the RH outer engine and transmission splash shield (6775) .
  1. Use Strap Wrench 303-D055 (D85L-6000-A) or equivalent to hold the water pump pulley (8509) while removing the four water pump pulley bolts.
  1. Remove the water pump pulley from the water pump (8501) .
  1. Remove the crankshaft pulley (6312) . Refer to the procedure in this section.
  1. Remove the five lower engine front cover bolts and the lower engine front cover .
  2. Ensure that the timing marks between the crankshaft sprocket (6306) and the oil pump housing line up.
  3. NOTE: The directional arrow is necessary to ensure that the timing chain/belt (6268) can be reinstalled in the same direction.
  4. Loosen the timing chain/belt tensioner nut.
  5. Remove the timing chain/belt .

  6. Installation
    NOTE: Ensure that the timing marks on the camshaft sprockets (6256) and the seal plate are properly aligned. Ensure that the timing marks on the crankshaft sprocket and the oil pump housing are still aligned. NOTE: A new timing chain/belt has three white timing marks that indicate the correct timing positions of the camshafts (6250) and the crankshaft (6303) . These marks will help ensure that the engine (6007) is timed properly. When the engine is properly timed each white timing mark on the timing chain/belt will be aligned with the corresponding camshaft and crankshaft timing mark on the sprocket. Because the white timing marks are not evenly spaced you will need to refer to the following illustration for proper timing chain/belt placement. There should be 40 timing belt teeth between the timing marks of the front and rear camshaft sprockets and 43 teeth between the timing mark on the front camshaft sprocket and the timing mark on the crankshaft sprocket .

    NOTE: Verify that the camshaft timing marks are aligned with the timing marks on the seal plate, and that the crankshaft sprocket timing mark is aligned with the timing mark on the oil pump (6600) .

    Install the timing chain/belt starting at the crankshaft sprocket and moving around to the camshaft sprocket following a counterclockwise path. Do not allow any slack in the timing chain/belt between the timing sprockets. After all of the timing marks are matched up with the timing chain/belt installed, slip the timing chain/belt onto the timing chain/belt tensioner .





Sep 20, 2009 | 1998 Nissan Quest

1 Answer

Timing for tropper 6cly and 4 camshafts and 24 valves model 2000


Timing Belt
Removal
1. Disconnect battery ground cable.
2. Remove air cleaner assembly.
3. Remove radiator upper fan shroud from radiator.
4. Move drive belt tensioner to loose side using wrench
then remove drive belt.
850RW001
Legend
(1) Crankshaft Pulley
(2) Cooling Fan Pulley
(3) Tensioner
(4) Generator
(5) Air Conditioner Compressor
(6) Power Steering Oil Pump
(7) Drive Belt
5. Remove cooling fan assembly four nuts, then the
cooling fan assembly.
6. Remove cooling fan drive pulley assembly.
7. Remove idle pulley assembly.
8. Remove serpentine belt tensioner assembly.
9. Remove power steering pump assembly.
10.Remove crankshaft pulley assembly using
5–8840–0133–0 crankshaft holder, hold crankshaft
pulley remove center bolt, then the pulley.
11. Remove right side timing belt cover then left side
timing belt cover.
12. Remove lower timing belt cover
13. Remove pusher.
CAUTION: The pusher prevents air from entering
the oil chamber. Its rod must always be facing
upward.
014RW011
Legend
(1) Up Side
(2) Down Side
(3) Direction For Installation
(4) Locking Pin
14. Remove timing belt.
CAUTION:
1. Do not bend or twist the belt, otherwise its core
could be damaged. The belt should not be bent at
a radius less than 30 mm.
2. Do not allow oil or other chemical substances to
come in contact with the belt. They will shorten
the life.
3. Do not attempt to pry or stretch the belt with a
screw driver or any other tool during installation.
4. Store timing belt in a cool and dark place. Never
expose the belt direct sunlight or heat.
6A–30 ENGINE MECHANICAL
Installation
NOTE: For correct belt installation, the letter on the belt
must be able to be read as viewed from the front of the
vehicle.
014RY00042
Legend
(1) Crankshaft Timing Pulley
(2) RH Bank Camshaft Drive Gear Pulley
(3) Water Pump Pulley
(4) Idle Pulley
(5) LH Bank Camshaft Drive Gear Pulley
(6) Tension Pulley
014RY00043
Legend
(7) Alignment Mark on Oil Pump.
(8) Alignment Mark on Timing Belt
(9) Alignment Mark (notch) on Crankshaft Timing
Pulley.
(10) Alignment Mark (groove) on Crankshaft Timing
Pulley.
014RW006
Legend
(1) Timing Belt
(2) Engine Rotation Direction
(3) Cylinder Head Side
1. Install timing belt.
1. Align the mark (notch) of crankshaft timing pulley
(2) with mark on oil pump (1).
Align the mark (groove) on the crankshaft timing
pulley (3) with alignment mark (white dots line) on
the timing belt (4).
NOTE: When timing marks are aligned, No.2 piston will
be on Top Dead Center.
014RW003
Legend
(1) Alignment Mark on Oil Pump
(2) Groove on Crankshaft Timing Pulley
(3) Alignment Mark on Crankshaft Timing Pulley
(4) Alignment Mark on Timing Belt
ENGINE MECHANICAL 6A–31
2. Align the alignment mark on the RH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover RH (3).
3. Align the alignment mark (white line) on the timing
belt (1) with alignment mark on the RH bank
camshaft drive gear pulley (2) (on the left side as
viewed from the front of the vehicle) and put the
timing belt on the camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
014RW00004
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover RH.
4. Align the alignment mark on the LH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover LH (3).
5. Align the alignment mark (white line) on the timing
belt (1) with the alignment mark on the LH bank
camshaft drive gear pulley (2).
When aligning the timing marks, use a wrench to
turn the camshaft drive gear pulley, then set the
timing mark between timing belt and camshaft
drive gear pulley and put the timing belt on the
camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
NOTE: It is recommended for easy installation that the
belt be secured with a double clip or equivalent clip after
it is installed the timing belt to each pulley.
014RW00005
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover LH.
6. Install crankshaft pulley temporarily and tighten
center bolt by hand (do not use a wrench).
Turn the crankshaft pulley clockwise to give some
belt slack between the crankshaft timing pulley
and the RH bank camshaft drive gear pulley.
2. Install pusher and tighten bolt to the specified torque.
Torque : 25 N·m (2.5 Kg·m/18 lb ft)
1. Install the pusher while pushing the tension pulley
to the belt.
2. Pull out pin from the pusher.
NOTE: When reusing the pusher, press the pusher with
approximately 100Kg to retract the rod, and insert a pin
(1.4 mm piano wire).
014RW011

Mar 18, 2009 | 2000 Isuzu Trooper

1 Answer

60,000 mile timing belt changed and it overheated and smoke a


You are talking about 2 different things here, YES the water pump should have been replaced with the timing belt. But the water tank you're talking about is it the radiator or a radiator reservoir. Either way they are not related to the timing job that was done. However I'm not by any means trying to blame the mechanic but sometimes the radiator can get damaged during a timing belt job is caution is NOT used when removing Crankshaft Pulley especially when using air tools. Good Luck contact if you need more help. Thanks for using FIX YA

Jan 06, 2009 | 2004 Kia Sorento

1 Answer

How Do i replace Water Pump on 98 Chevy Metro


  1. Remove the negative battery cable.
  2. Drain the engine cooling system.
  3. Remove the air cleaner assembly.
  4. Remove the A/C compressor suction pipe bracket (if equipped).
  5. Loosen four water pump pulley bolts. Do not remove the bolts.
  6. Raise the vehicle. Support the vehicle. Remove the right lower splash shield.
  7. Remove the right lower splash shield.
  8. Remove the A/C compressor drive belt (if so equipped) by releasing the tensioner pulley and removing the belt from the crankshaft and compressor pulleys.
  9. Loosen the generator adjusting bolt (1), pivot the generator and remove the water pump/generator drive belt.
  10. Remove the crankshaft pulley.
  11. Remove the water pump pulley (four bolts).
  12. Remove the timing belt.
  13. Remove the oil level indicator (dipstick) guide tube.
  14. Remove the upper generator adjusting bracket from the water pump (one bolt).

    1. Remove the rubber seals from the water pump.
    2. Remove the water pump mounting bolts and nuts.
    3. Remove the water pump and gasket from the vehicle.
    4. Clean the water pump and the gasket mating surfaces.
    5. Install the water pump.
    6. Secure the water pump with mounting nuts and bolts. Tighten Tighten the water pump mounting nuts and bolts to 13 Nm (115 ft. lbs.).
    7. Install new rubber seals (1) to the water pump (2).
    8. Install the upper generator adjusting bracket to the water pump (one bolt).
        • Tighten the upper generator mounting bracket bolt to 23 Nm (17 ft. lbs.).
      1. Install the oil level indicator (dipstick) guide tube.
      2. Install the timing belt.
      3. Install the water pump pulley.
      4. Finger-tighten the four bolts.
      5. Install the crankshaft pulley.
      6. Install the water pump/generator drive belt to the crankshaft, water pump and generator pulleys.

Nov 20, 2008 | 1998 Chevrolet Metro

2 Answers

I need instructions on replacing the timing belt


1. Remove the Alternator Belt.
2. Remove the Water Pump Pulley
3. Remove the Air Conditioner Belt and Power Steering Belt.
4. Remove the Crankshaft Pulley.
5. Remove the timing belt cover
6. Remove the timing belt tensioner pulley.
7. Remove the Timing Belt.
8. (If Replacing) Remove Idler Pulley.
Installation is reverse of removal. Keep a close eye on the timing marks on the cam sprockets to make sure you don't knock anything out of whack.

I would strongly recommend replacing the water pump while you are replacing the timing belt. (The water pump usually comes in the timing belt kit.) Otherwise you are going to have to do this all over again when your water pump goes out. Good Luck.

Nov 10, 2008 | 2004 Hyundai Tiburon

Not finding what you are looking for?
2006 Kia Sorento Logo

271 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...