An expert who has achieved level 3 by getting 1000 points
An expert that got 10 achievements.
An expert that got 5 achievements.
An expert whose answer got voted for 100 times.
Re: 1990 Buick Century Limited StationWagon power mirror...
The courtoesy fuse usually does those or one of the silver circuit breakers but the miror switches do go bad because sometimes if they are in thecenter consol ccoffee and soda get spilled on them and over time get stickey and gummed up and if on the door water if we forgot and left a window open and it rained and jsut normal wear and tear
If hyou find this information helpful please give me a fixya! and if I can be of any more help please contact me right away
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
There is a fuse for the ignition module , ELEK IGN 15 amp . Really don't think this would be your problem , more then likely the crankshaft position sensor or the ignition module is . Your best bet have it towed to a qualified repair shop.
Most cars have the rear-view mirror and the little metal mount that it slides into. If the whole thing has fell off it is an easy fix.
Go to an auto parts place and tell the counter person you need the glue to glue your mirror mount to the windshield. They will know what to give you.
Then you clean the spot the mirror was hung with alcohol. Let dry
Then follow package directions. Basically you do a dab of glue on mount and press to windshield and hold for a bit of time. Then you wait like 12-24 hrs before sliding the mirror onto the mount.
On the other hand if you are asking for a new mirror you can get one from the Buick dealership - parts dept. or a junkyard or just attach any kind of rear-view mirror. Sorry I can't help you if you have a wired mirror.
The first thing to do would be to hook up a factory or professional type scan tool an check for DTC'S - diagnostic trouble code's . This vehicle has very complex electronic's. Serial data communication network,class2 data bus . There are electronic modules inside the door's that control the lock's ,power window's , power mirror's . Your best bet ,take it to a qualified repair shop . Not a fuse problem , driver an passenger door module each have thier own power supply. Two circuit breakers ,PWR/WDO circuit breaker 30 amp. You could check DRVMDL 10amp fuse ,located in the rear fuse box , PASSMDL 10amp fuse rear fuse box , RRDR/MDL 10 amp fuse rear fuse box . Rear fuse box is under the back seat . None of the window's , lock's etc.. work from any door switch ?
ralipka, Most auto parts stores carry kits for your problem. Before you start the process of putting the mirror back on, mark the position of the mirror on the outside of the windshield with a magic marker or whiteout so you know where to place the mirror. Once you clean the area on the inside you will not see where the mirror was. Good luck with this.
This is what you do take the door skin off of the inside of the door and at the top corner there will be i think three nuts and than your going to need door clips after your done in order to put the door panal back on
There is a small plastic piece (triangular shape) at the top of the door panel, opposite of the mirror. It is held in place by a plastic clip. You can gently pop that out, with a flat blade screwdriver or something similar. That will expose 3 bolts with nuts on them. On my 2000 Century, they are 10 mm. Take off those three nuts, and the mirror will come off.
On the inside trim, you can remove screws that are by the door handle,
arm rest, under door and side of door and then gently pull back on the
panel as there will also be retaining clips attached and you don't want
to break them. You'll need to lift the door panel upwards in order to
get it off the window ledge. Then you'll need to manipulate the panel
and disconnect the door handle linkage from the door handle and
disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door