Jeep Liberty '03...need to repair rear window washer/sprayer and probably tube....that snapped off. Parts needed? Access through bumper?? Thank you for ANY suggestions.

There's this website www.reliable-store.com
They have books on ALL vehicles.
it covers wiring diagrams, electrical diagrams,
fuse diagram, torque specs, PCV, error codes, fault codes, service info, repair info, parts info, troubleshooting owner's/service/repair/parts/maintenance manuals
etc everything totally..
I have 1987 toyota 4runner model and I keep servicing and when needed repair it on my own. worth it !!!

The rear wiper has its own pump motor. pull the hose from the wiper and have someone engage to see if there is a clog. do the same at the motor. if bo liquid comes out then its the pump. also check fluid level in reservoir as well as a possible secondary reservoir

PROBABLE CAUSE Impact to the front bumper pushes the bumper back far enough to break the washer pump hose fitting. CORRECTIVE ACTION Replace the windshield washer reservoir and washer motor with updated parts. REPAIR PROCEDURE 1. Turn the ignition switch to ACC (I) to unlock the steering column. 2. Raise the vehicle on a lift. 3. Remove the right front inner fender. Unhook and pull back the bumper for better access. CLIPS (6 places.) SCREWS (6 places.) RIGHT FRONT INNER FENDER 4. Release the hooks on the upper right side of the front bumper. 5. Remove the clip from the filler neck, then remove the filler neck. FILLER NECK CLIP WINDSHIELD WASHER RESERVOIR CLIP WASHER MOTOR CONNECTOR BOLT BOLTS WASHER TUBES 6. Remove the right front fender trim, and disconnect the washer hose from the 90-degree fitting. CLIP FRONT FENDER TRIM FRONT HOSE 7. Disconnect the 2P connector and the two washer tubes from the washer motor. 8. Remove the washer reservoir clip and the three bolts, then pull out the reservoir. 9. Assemble the new reservoir components, but do not install the filler neck. 10. Trim 85 mm off the end of the 1,260 mm washer tube only. 11. Route the washer tubes on the reservoir. NOTE: The black fitting is for the front windshield nozzles, and the white fitting is for the rear nozzle. 85 mm 12. Install the reservoir. 13. Connect the rear tube to the straight fitting in the wheelwell. 14. Connect the 2P connector to the washer motor. NEW RESERVOIR Connect the rear washer tube. CLIP BOLT 9.8 N•m (7.2 lb•ft) 15. Install the filler neck with the original clip. Connect the front washer tube to the 90-degree fitting. Then reinstall the front fender trim. WASHER FLUID DIPSTICK 2P CONNECTOR FRONT FENDER TRIM FILLER NECK CLIP

1. Remove the screws that secure the license plate lamp assembly to the rear bumper fascia
2. Pull the license plate lamp assembly down and out through the mounting hole in the rear bumper fascia far enough to access and disconnect the wire harness connector.
3. Remove the license plate lamp assembly from the rear bumper fascia.

I HOPE THIS YOU TUBE VIDEO HELPS ">

no easy way to fix .just got to take out the side pannel . be carefull the plastic is very brittle

CHeck the KJ Service & Repair Manual Secc-23-Body (page 128 and next, for Rear Door).

I really hope helps with this (remember rated this help) Good luck.

Watch this fix-it-yourself Jeep Liberty Power window video on You Tube:

">

I usually spray guide tracks with a silicone spray. It works pretty well. Up north where I am, when sprayed on door seals it keeps doors from freezing closed as well!

use small box wrench and remove the catch attached to the window. insert 2 washers over each of the 2 connecting bolts ..4 washers required min 2 per side. re attach window catch. This should move the catch forward ehough to depress the locking mechanism.... it worked perfect on my 02 Liberty.