Question about 1988 Chevrolet S-10

2 Answers

1988 chevy s-10 4x4 sensors

On my truck i have a sensor located on the head between the cylinder number 1 and number 3 spark plugs that is broken where the wires hook into it and i need to know what kind of sensor it is.The book i bought ( a haynes repair manual) does not have a sensor even located there. I need to know if it is a knock sensor for my esc system or something else.

Posted by russangione on

  • Anonymous May 11, 2010

    im not a profession all but i got a s10 and i think its the temp wires for your guage.

×

Ad

2 Answers

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Temperature sensor...

Posted on May 09, 2009

Ad

rachel stephens

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 130 Answers

Tempature sensor

Posted on Feb 10, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of temp sensor on a 2007 3.6 cadilac cts.


Engine Coolant Temperature (ECT) Sensor (LP1/LY7)
In the engine compartment, in the left side of the left cylinder head, between cylinders #2 and #4

Engine Coolant Temperature (ECT) Sensor (LS2)
In the engine compartment, towards the front of the left cylinder head, near #1 spark plug

May 17, 2018 | Cars & Trucks

1 Answer

I have a 1999 GMC 350 I need the head torque specs just replace head gaskets can anyone help



  1. Clean the cylinder gasket surfaces on the engine block.
  2. Inspect the dowel pins (cylinder head locator) for proper installation.
  3. Clean the cylinder head gasket surfaces on the cylinder head.
  4. Place the NEW cylinder head gasket in position over the dowel pins (cylinder head locator).The cylinder head gasket is not directional and may be installed using either side facing the engine block.
  5. Install the cylinder head to the engine block. Guide the cylinder head carefully into place over the dowel pins and the cylinder head gasket.
  6. Install the cylinder head bolts.
  7. Tighten the bolts in the sequence shown in the image below on the first pass to 30 [n-m] (22 lb ft).

  8. Use a torque angle meter in order to tighten the cylinder head bolts in sequence on the final pass. Tighten:
    • Tighten the long bolts (1, 2, 5, 6, 9, 10, and 13) on the final pass in sequence to 75 degrees.
    • Tighten the medium bolts (14 and 17) on the final pass in sequence to 65 degrees.
    • Tighten the short bolts (3, 4, 7, 8, 11, 12, 15, and 16) on the final pass in sequence to 55 degrees.

  9. Measure the NEW spark plugs for the proper gap.Adjust the spark plug gap if necessary.
    Specification:
    Spark plug gap to 1.52 mm (0.060 in)
  10. Install the NEW spark plugs. Tighten:
    • Tighten the spark plugs for a USED cylinder head to 15 [n-m] (11 lb ft).
    • Tighten the spark plugs for the initial installation of a NEW cylinder head to 30 [n-m] (22 lb ft).

  11. If reusing the engine coolant temperature (ECT) gauge sensor, apply sealant GM P/N 12346004 to the threads of the ECT gauge sensor.
  12. Install the ECT gauge sensor.Tighten:
    Tighten the ECT gauge sensor to 20 [n-m] (15 lb ft).


head torque-zavst4atb1a5mamouuek2kkm-3-0.png

Mar 20, 2018 | GMC Cars & Trucks

1 Answer

Where is bank 1 sensor 1 located on a 1998 Chevy Venture van


If your talking the 02 sensor, it's in the exhaust. Bank one is the bank with the number 1 cylinder and sensor 1 is the first 02 sensor.
The number 1 cylinder shows to be located in the rear bank. If you only have two 02 sensors, that would be one before the cat and one after.

Jan 12, 2016 | Cars & Trucks

1 Answer

P0057 - Where is Sensor 2 Bank 2 Located?


On V engines one of the cylinder heads is located further forward than the other. That is the side that has cylinder #1 on it. That is bank 1. The other side is bank 2. There are 2 oxygen sensors-one in front of the cat convertor and one behind it. Sensor 2 is behind the convertor. It looks kind of like a spark plug with wires coming out the top

Dec 31, 2013 | Hyundai Sonata Cars & Trucks

1 Answer

1991 chevy s10 number one cylinder has antifreeze build up


spray from hose during heat soak after shutting off.
possible head gasket leak. leaky crossover between heads. or
cracked /broken head.

Feb 21, 2013 | 1991 Chevrolet S-10

1 Answer

Where is bank 1 sensor 2 located in a 1996 mitsubishi galant s?


Locate the number 1 spark plug and then locate the O2 sensor in the exhaust. The one you see nearest the cylinder head is number 1. Look underneath the vehicle and locate the catalytic converter and the number 2 sensor is just before the "cat" and the one after is the Bank 2 sensor 2. I believe that the number one cylinder is closest to the radiator and the front of the engine. If this is a 4 cylinder car it is the sensor in the exhaust just prior to the catalytic converter. You will need a 7/8" or 22mm wrench and a good rust penetrant to remove the sensor without incident. Let me know if you need anything else.

Jul 10, 2011 | Mitsubishi Galant Cars & Trucks

1 Answer

What is bank 1 sensors location on ford contour


Bank 1 is where the number one cylinder/spark plug is located. If this is a 4 cylinder engine, number 1 is at the front of the motor and bank 1 is irrelevant and the number 1 sensor would be the one screwed into the exhaust manifold attatched to the cylinder head. If it is a 6 cylinder than number one is on the side closest to the radiator, and at the back of the engine near the exhaust crossover. The number 1 sensor is going to be the one screwed into the exhaust manifold just outside the cylinder head.

Jun 29, 2011 | 1999 Ford Contour

1 Answer

Need firing order to 89 chevy s-10 p/u w/ 4.3 liter/6cyl. replacing plug wires


4.3 v/6 firing order for an S-10 Chevy is 1-6-5-4-3-2, a helpful tip to always locate # 1 spark plug on a v engine.
If you look carefully at the cylinder heads note the very front of each, do you see one sticks out slightly further to the front then the other?
Tghis is the way these engines have to be cast for proper cylinder and timing rotation.
The furthest forward cylinder head is in fact the home of #1 cylinder, it is the first spark plug on that head, which in this case is the right side head.

Jun 09, 2010 | 1988 Chevrolet S-10

Not finding what you are looking for?
Cars & Trucks Logo

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...