Question about Daewoo Nubira

1 Answer

My car was not properly jacked up and fell. Was making noise mechanic thought it was the rotor and replace it. still makes grinding noise. What could be causing to still be making noise

Posted by elleybaby on


1 Answer


  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 62 Answers

The dust shield behind rotor could be touching wheel or rotor,safly jack up vehice take tire off of suspected side, inspect dust shield carefully if bent . id shouldnt take much to straighten out.

Posted on Aug 04, 2008


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Brakes make a whistle noise when applied and sometimes a low grown or grinding when coming to a slow stop or start.

A grinding or rumbling noise can also be symptoms of a wheel bearing or constant velocity joint in a driveshaft. A worn wheel bearing can also cause a 'whistling' sound (as can a worn CV joint).

A grinding noise with brakes is either worn pads causing metal to metal contact on the brake disk/rotor, or the brake backing plate catching on a spinning rotor ... or a loose/missing anti squeal brake shim (they stop the pads from rattling and vibrating).

However, as you say a mechanic has looked at the brakes and can't find anything wrong .. I think I would begin to suspect a wheel bearing or constant velocity joint on the driveshaft (front wheel drive cars).

May 05, 2016 | 2007 Honda Accord Sedan

1 Answer

Have a metal grinding noise when turning left only.

Replace the right side wheel bearing. But before you replace it. Listen to see if the noise is coming from the front or back. If you can't tell, Put some one in the back seat. Front bearings usually make noise. rear bearings, the noise can come and go.

Jun 26, 2015 | 2011 Jeep Patriot Latitude

1 Answer

While changing the left front tire, my car fell off the jack and now there is a loud grinding noise coming from that tire. What could that noise be?

next time use jack stands. very bad using only a jack for anything.
take it to a mech, and get it fixed , you busted the brakes.
its dangerous to drive too.
if DIY guy, with tools, then you can do this.
spin the rotor (use jack stands and not get killed)
does the rotor wobble , bingo , new rotor time
is it making noise, bingo you bent the backing place, rebend it back.

Dec 01, 2013 | 1991 Honda Accord

1 Answer

Rear tire noise

How many miles on your 328? My son's car was making a grinding noise and our independent mechanic told me it was the rear differential. I assumed he was correct and bought a replacement. However, before I installed it, I noticed the outer 3/4" of his passenger side rear rotor was discolored and no longer shiny. His brake caliper was grinding the rotor! It was because the hub bearing was so badly worn. I replaced the bearing and all is well.

Feb 01, 2013 | 1997 BMW 328

1 Answer

Ford chunky braking

I see the rotor keeps being replaced; was the caliper ever replaced? A caliper piston sticking (release very slowly or doesn't release all the way) can create all kinds of problems such as: pulling to one side, glazing and warping of rotor and uneven pad wear. Grinding noise could be pads sensor digging into rotor which will also give the rotor the vertical line you mentioned. I recommend having caliper checked to see if it's working properly. A note on purchasing rotors; you don't want to buy the cheapest ones. Go for the premium ones as they dissipate the heat better, lessening the chance for warping and glazing. Same thing goes for the pads. A majority of braking is done by the front brakes therefore you want the better quality stuff on the front. Also it's best to replace calipers, pads and rotors on both sides at the same time. If you replace one side only you will end up replacing the other side not long after. If it has not been done, you may want to have steering components checked and greased. If these parts are not greased properly it can cause grinding noise, pulling to one side just to name a few. I hope this was helpful.

Mar 17, 2017 | 2011 Ford Fiesta 1.6

2 Answers

98 audi a4 quattro 2.8 liter

Wheel bearing maybe, if you just did your brakes, the heat sheild behind the rotor is probably rubbing, take the wheels off and spin the wheel and then look behind it, should be easy to find. I assume you did it the right way with pads and new rotors :).

Apr 15, 2010 | 1998 Audi A4

1 Answer

My 95 toyota corolla makes grinding scraping noise when going uphill. It's coming from the right front of the car. Almost sounds like it's coming from the breaks or transmission. A mechanic thinks it could...

Bad motor mounts will not usually cause the kind of noise you describe they will cause more vibration to be felt at all times.

Sometimes the brake rotor dust cover plate can rub against the rotor and make a grinding/scraping sound. Raise the car, remove the wheel, and check the clearance between the dust cover and the rotor.

If your shocks/struts are bad the tire could be rubbing against the strut. Check the strut.

Dec 12, 2009 | 1995 Toyota Corolla

2 Answers

Replacing the rotors on a 300 what are the steps that should be taken I hear a griding noise like something is lose please advise

Are your pads warn out ??
Is it metal on metal ?
If you can not determine if you pads are warn out - you should not attempt to replace pads and rotors yourself..

Rate well ;o)

Jul 22, 2009 | 1999 Chrysler 300M

1 Answer

New brakes still making grinding noise

Sounds like it is your hub bearings.  Jack the car up and check for play in the hub bearings.  More than likely this is your issue and the bearings need to be replaced.  Hope this helps.  Thanks for an honest rating.

May 19, 2009 | 2002 Isuzu Rodeo Sport

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers


Level 3 Expert

85239 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

459 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides