At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
Drain cooling system. Remove radiator upper cross-member. Remove radiator fan. Remove accessory drive belts. NOTE: The water pump is driven by the primary timing chain. Remove the timing chain and all chain guides then remove water pump and gasket. Reverse to install. Since this job requires about 4 special tools and the removal of the timing chain and a high level of technical skill I would not attempt it, if you get the timing chain on wrong you could cause severe damage to the engine.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
may have faulty thermostat, or blocked radiator . Although if thermostat has been removed the engine can over heat at speed as coolant passes through radiator too fast to give off sufficient heat to cool engine
Cv joints in your intrepid? Remove the tire, unbolt the lower ball-joint, Remove the hub nut, pull outer joint from wheel bearing, pull shaft from transmission.
Step 1
Lay out a drop cloth underneath the Dodge Intrepid to protect the floor from coolant spills. Designate an area to lay out each part alongside its bolts and connecting hoses and wires. Use a drop cloth here as well, some of the parts will have traces of grease and coolant.
Step 2
Disconnect the negative battery cable, using a screwdriver to unscrew the clamp that secures the cable to the negative (-) post. Pull the cable away from the battery post.
Step 3
Use a jack to elevate the Dodge Intrepid and jack stands to shore up the jack. Release the pressure in the radiator by removing the cap. Take out the drain plug located underneath the radiator. Catch the coolant in a resealable container
Step 4
Use a grease pencil to mark on the timing belt its position in each pulley before removal. This will save time when reinstalling. If needed, replace the timing belt and skip marking the old one.
Remove the Damaged Pump
Step 1
Locate the water pump on the Dodge Intrepid. It's mounted on the front of the engine block and connected to the radiator and various other parts through a series of hoses. It's rotated by the timing belt. Study these parts, as you'll have to remove them.
Step 2
Disconnect or remove the parts in front of the water pump, using an adjustable wrench. In the most common Dodge Intrepid engine--the 2.7L--you'll find, in order: the upper radiator crossmember, fan module, accessory drive belts, crankshaft damper, timing cover, timing chain and guide wires.
Step 3
Unbolt the water pump from the engine block, using an adjustable wrench. You may have to use a chisel to gently break the seal between the mount and the pump. Discard both the pump and the bolts.
Step 4
Clean off the mounting area with a shop rag.
Install the New Pump
Step 1
Inspect the new water pump to ensure it's identical to the old pump and free of any metal splinters or debris.
Step 2
Arrange the new water pump on the mount. You won't need sealant for the o-ring on a Dodge Intrepid. Hold the water pump and o-ring in place as you secure it with the new bolts. Tighten them with a torque wrench to 105 inch pounds torque in any order.
Step 3
Install the timing belt and wires, using the grease pencil marks to guide you in installation. Install the rest of the parts in the order removed. The camshaft must be reconnected with a torque wrench at 125 foot pounds torque.
Step 4
Replace the radiator's drain plug and refill the radiator with the amount and type of coolant specified in your owner's manual. Release the jack and jack stands.
Step 5
Attach the negative battery cable to the post and tighten the screw on the clamp. Crank the Dodge Intrepid's engine and check for leaks. Then, close the hood.
Hi....
The Water pump on your Intrepid 2.7L.
Is located in front of the engine, But you can't see because is inside of the timing cover.
And the Water pump is driven by the Timing chain.
I hope this help on your question.
Thank you for use fixya..
The relay. There is a black box on the right hand side of the engine at the top corner. It encloses all the relays. Make sure you are looking at the diagram well. Exchange the relays and remove the wiper relays and exchange them with the radiator fan relays. Start the engine, run it for 5 mins and see if they kick-start.
×