Question about 1990 Ford Bronco

1 Answer

1990 bronco,ignition switch turned freely,no contact with anything,took off ignition module ,switched the slide by hand ,,fuel pump,radio,is all that comes on,,no starter ,nothing..

Posted by broncoguy511 on

Ad

1 Answer

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 60 Answers

Look at the starter solenoid .

Posted on Mar 04, 2011

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Has spark, no fuel, wont start


auto shutoff relay is bad.. change it..controls pump and ignition..

Jan 02, 2014 | 1990 Ford Bronco

1 Answer

Truck cranks but won't start


If your fuel is running all the time the PCM is bad if you take your relay out and the fuel pump stays running its a short

Jan 06, 2013 | 1990 Ford Bronco

1 Answer

Fuses panel described in English


Hope this helps your out. I know the diagram and locator is a bit blurry but hopefully it gets what you need.
Drivers kick panel:
Front wiper 20A - Front wiper system Cigar 15A- Cigarette lighter Audio 10A- Audio, remote control mirror Air Bag 10A -Air bag diagnostics Stop lights- 15A -Rear brake light, high mounted stop light ECU B+ 10A - Shift lock actuator, transaxle controle module, radio, engine control module Room 10A - Interior light, clock, ignition key reminder, rear cargo area light switch ABS 10A- Anti lock brake system control unit ECU IG1 10A - Transaxle control module, shift lock actuator, ABS control unit, DRL unit Meter 10A - Instrument panel, back-up switch, electronics time control module, inhibit switch Turn signal 10A- Hazard switch ,front and rear turn lights, turn indicator IGN1 20A - Ignition switch ABS 30A- ABS pump motor TNS 30A- Tail light, license plate light COOL/FAN 30A- Cooling fan Cond/Fan 20A- A/C condenser fan Starter 15A- Start signal , Fuel pump Blower 25A- Blower Motor SR/ACC 10A - Ignition switch Hazard 15A - Hazard and turn signal light D/Lock 25A- Door locks ABS 30A - Anti lock brake system control P/W RH 20A- Power window motor right hand P/W LH 20A- Power window motor left hand IGN2 25A- Ignition Switch
Engine compartment :
Head 25A- headlights IG 2 30A- Ignition switch IG coil 15A -Ignition coil, condenser,generator IC regulator, diagnostic connector. O2 down 10A- Rear O2 sensor O2 up 10A- Front O2 sensor Fuel pump 10A -Fuel pump unit Injector 10A -Fuel injector ,camshaft positioning sensor, purge solenoid valve, EVAP, IAC actuator, Mass Airflow sensor, EGR stepper motor. fuel pump relay coil, vehicle speed sensor. A/Con 10A - A/C compressor controls, cooling fan BTN 30A- Brake light , high mounted stop light. Tail light LH 10A- License plate light, tail light , rear combo light, instrument panel illumination Tail light RH 10A-License plate light, tail light , rear combo light, instrument panel illumination Head low 15A- Headlight Head Hi 15A-Headlight Horn 15A- Horn jlmacman.png jlmacman_0.png

Inside kick panel jlmacman_1.png

Mar 07, 2011 | 1995 Kia Sephia

2 Answers

My 93 cougar like sputters when running. no power, and idles real hard. what could this be?


I'm guessing fuel pump is going. Check for 40 PSI pressure with fuel pressure gauge. Check in engine comaprtment.
Section 10-01: Fuel Tank, Filters, Lines and Electric Fuel Pump 1995 Thunderbird, Cougar Workshop Manual
DESCRIPTION AND OPERATION Fuel Pump, Electric The electric fuel pump:
  • Is part of the fuel pump module.
  • Is located in an internal reservoir in the polyethylene fuel tank (9002) .
  • Is mounted with its inlet at the bottom of the reservoir.
  • Is designed to increase satisfactory pump operation during extreme vehicle maneuvers and steep climbs with low fuel levels.
  • The high-pressure fuel pump module on the 3.8L SFI and 4.6L-2V engines can supply 60 liters (15.9 gal) of fuel per hour at a working pressure of 269.0 kPa (39 psi).
  • The fuel pump module on the 3.8L SC SFI engine can supply 125 liters (29.0 gal) at the same rate and pressure.
  • The fuel pump module has an internal check valve to maintain pressure in the system after the engine is shut down.
  • The fuel pump module also has an internal release valve to provide protection from too much pressure if fuel flow becomes clogged in the fuel filter (9155) , the fuel line is damaged, or other factors.
  • Overpressure is limited to 850 kPa (123 psi) and reduced fuel flow will result if the pressure relief valve is activated.
  • The fuel pump module is protected at its inlet by a nylon fuel filter element (9365) which filters contaminants which could plug or damage fuel pump components.
  • The fuel filter element simultaneously allows passage of small quantities of water which may accumulate within the tank reservoir.
  • The electrical system has a fuel pump control relay in the powertrain control module (PCM) (12A650) which provides power to the fuel pump module through an inertia fuel shutoff switch (IFS switch) (9341) that is normally closed.
  • The electrical system provides power to the fuel pump module through two relays:
    • Fuel pump power relay.
    • PCM power relay.
The current path depends on operating conditions.
  • When the ignition switch (11572) is OFF, contacts of both relays are open.
  • When the ignition switch is first turned to RUN, the PCM power relay energizes and closes its contacts.
  • Power is sent to the fuel pump relay and a timing device in the powertrain control module .
  • The fuel pump module runs through the contacts of the fuel pump relay.
  • If ignition switch is not turned to START, the timing device in the powertrain control module will open ground Circuit 57 after about a second.
  • Opening the ground circuit deenergizes the fuel pump relay, which opens its contacts and de-energizes the fuel pump.
  • The circuitry provides pre-pressurization of the fuel system.
  • When the ignition switch is turned to START, the powertrain control module operates the fuel pump relay to provide fuel while cranking.
  • After the engine starts and the ignition switch is ON, power to the fuel pump module is again supplied through the fuel pump relay. The powertrain control module senses engine speed and shuts the fuel pump module OFF by opening the ground circuit to the fuel pump relay when the engine stops or is below 120 rpm.



eab1c32.gif

Oct 26, 2010 | 1993 Mercury Cougar

2 Answers

1987 ford bronco engine wont start


there is a two piece control module and pick up in distributor you could replace these or try a used distributor

Jul 23, 2009 | 1987 Ford Bronco

1 Answer

Fuel pump switch


also known as the inertia switch is located on the left kick panel area by the emergency brake pedal . 90 full size bronko .

J5

Jan 16, 2009 | 1990 Ford Bronco

Not finding what you are looking for?
1990 Ford Bronco Logo

Related Topics:

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14866 Answers

Mike

Level 3 Expert

4372 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...