Question about 2001 Hyundai Accent

1 Answer

I have a 2001 Hyundai accent. My rear would make a (thunk thunk) noise when slightly breakin for a stop. Its more towards the middle of the rear. Any ideas?

Posted by Anonymous on

Ad

1 Answer

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 10 Answers

I would check to see if you have a warped brake disc in the rear since it is only when braking.

Posted on Feb 28, 2011

  • Anonymous Feb 28, 2011

    As a followup, this won't be visible to the naked eye - you will have to have it micrometered

×

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 Aztek rear brakes thunking noise.


rear sway bar link pins and bushings

Oct 18, 2012 | 2001 Pontiac Aztek

1 Answer

Replace lecence plate light on 2005 hyundai accent


A slightly better set of instructions might help you. Mine is a 2003 Accent. You have to remove the access panel that covers the lamps and the wiper control. Remove the phillips screws along the bottom of the panel (closest to the floor of the trunk when the lid is closed). Then remove the two screws that hold the brackets onto which the two strings are linked which are used to raise the rear deck slightly when the trunk opens. Next, there is a small cover underneath the rear wiper (about 2 inches square) that you need to carefully pry off using a small flat head screw driver via the indents on the lower side of the plastic cover. Inside you will find a 10mm bolt; use a ratchet to remove the bolt. Next, using a small flat head screw driver, carefully pry the middle section of moulding between the panel you are removing and the molding that covers the top portion of the back glass. There are two clips at the base of each middle moulding piece closest to the panel you are removing. Once those pop free, grab the panel at the bottom and firmly but gently pull away from the car body to pop free the two retaining clips holding the moulding to the car body. Finally, use one hand to grasp the panel from the bottom and the other to help help slide the panel "up" towards the glass (top of the car). The panel's top is flanged, and must slide up and away from the lip on which it sits. With the panel removed, grasp the white socket that holds the bulb and with gentle pressure turn it counter clockwise about 40 degrees and then pull the socket out. The replacement bulb is a type 168. Reverse these instructions to assemble, making sure in the end to push all retaining clips back into place until you hear them "catch" and hold the panel firm;y against the car body so that you do not get vibration noise.

Nov 15, 2009 | 2005 Hyundai Accent

2 Answers

Squealing noise when in reverse


Is the noise under the hood? or where?

If under the hood, most likely the engine has a bad motor mount. The engine will "twist" slightly to one direction when driving forward and "twist" in the opposite direction when you drive in reverse.

When it is twisted (in reverse) an engine pulley or fanbelt is scraping on some plastic part, or whatever, and making the noise.

If not under the hood, it may be one of the front brake pads that have a "worn brake pad" sensor. The sensor is an L-shaped piece of metal that scrapes the rotor when the brake pad backing gets too close to the rotor, hence worn brake pads.

If the noise is somewhere else, maybe another "expert" has a suggestion.

Please post more information... Thank you.



Sep 10, 2009 | 2001 Hyundai Accent

1 Answer

Engine rattle stopped when clutch failed


Most likely its in the clutch, could have been a spring in the clutch disc come loose or out, or the throut bearing went bad, whatever it was they will find out when they replace the clutch.

May 06, 2009 | Hyundai Motor 1995 Accent

1 Answer

2001 Hyundai Accent dies while driving


I had a similar problem and had an engine tune up done and the car runs almost like new now. Mine is a 2001 Hyundai Accent too.

Apr 16, 2009 | 2001 Hyundai Accent

1 Answer

2003 Hyundai Accent Rear Brake Noise


the rear shoes need to be cleaned and adjusted. nothing to worry about unless it annoys you too much.

Mar 29, 2009 | 2003 Hyundai Accent

2 Answers

Hyundai Accent SI-back windscreen wiper


there is a 15 amp fuse for the rear wiper under the bonnet check this, also i think the accent has a seperste switch in the dashboard for the rear wiper like th hyundai coupe.


Mar 24, 2009 | 2000 Hyundai Accent

3 Answers

Replace license plate light 2005 Hyundai Accent


A slightly better set of instructions might help you. Mine is a 2003 Accent. You have to remove the access panel that covers the lamps and the wiper control. Remove the phillips screws along the bottom of the panel (closest to the floor of the trunk when the lid is closed). Then remove the two screws that hold the brackets onto which the two strings are linked which are used to raise the rear deck slightly when the trunk opens. Next, there is a small cover underneath the rear wiper (about 2 inches square) that you need to carefully pry off using a small flat head screw driver via the indents on the lower side of the plastic cover. Inside you will find a 10mm bolt; use a ratchet to remove the bolt. Next, using a small flat head screw driver, carefully pry the middle section of moulding between the panel you are removing and the molding that covers the top portion of the back glass. There are two clips at the base of each middle moulding piece closest to the panel you are removing. Once those pop free, grab the panel at the bottom and firmly but gently pull away from the car body to pop free the two retaining clips holding the moulding to the car body. Finally, use one hand to grasp the panel from the bottom and the other to help help slide the panel "up" towards the glass (top of the car). The panel's top is flanged, and must slide up and away from the lip on which it sits. With the panel removed, grasp the white socket that holds the bulb and with gentle pressure turn it counter clockwise about 40 degrees and then pull the socket out. The replacement bulb is a type 168. Reverse these instructions to assemble, making sure in the end to push all retaining clips back into place until you hear them "catch" and hold the panel firm;y against the car body so that you do not get vibration noise.

Mar 24, 2009 | 2005 Hyundai Accent

1 Answer

Can not pumb Gas into Hyundai 2001 accent


Try moving the handle in a different position, or don't put the nozzel all the way in. The vent tube could be clogged.

Mar 13, 2009 | 2001 Hyundai Accent

1 Answer

2001 Hyundai Accent new rear brake noise


jack up the rear wheel and spin it, do this with the other wheels chocked for safety, and listen for any rubbing sound, do this with both rear wheels and if one is bad then remove the drum again to check if the retainer has come off of the brake lining, hope this helps you.

Jan 07, 2009 | 2001 Hyundai Accent

Not finding what you are looking for?
2001 Hyundai Accent Logo

Related Topics:

226 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14850 Answers

Brad Brown

Level 3 Expert

18520 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...