Question about 2001 Honda Accord

1 Answer

Recently the cruise control would not set to the desired speed

Posted by sheridan_nau on

  • david balderston Feb 14, 2011

    do you have any lights on like check eng or abs this can cause you cruise to shut down

×

Ad

1 Answer

david_davemo

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 880 Answers

In many cases that is caused by a leaking vaccum hose.

Posted on Feb 14, 2011

Ad

5 Related Answers

Anonymous

  • 1 Answer

SOURCE: cruise control fails to engage on '03 ford sport trac

Th is is how I fixed mine! Down on the brake pedal there is a small plastic box about 1 1\2 * 1 1\2 in size. It's called the brake stop light, I think. This part disengages the cruise when the brake is pressed. Not sure on it's other uses! Remove the clip from the part where it attatches the the pedal. For more working room you can remove the plastic keeper. The box has three keepers on it. Pry them out gently to remove the top. Two of the copper pieces inside will have contacts on them about the size of a match stick head. Take them out and clean them with an eraser. This solved my problem, I hope it solves yours. Let Me KNOW!

Posted on Dec 28, 2008

Ad

Anonymous

  • 64 Answers

SOURCE: 1998 dodge ram 1500 Cruise control , speed

Look under the hood to check and make sure there is two steel wire cables connected to the throttle body. i had the same problem on my 02 dodge ram, turns out that just one of the cables came loose

Posted on Sep 15, 2009

Anonymous

  • 1 Answer

SOURCE: cruise control will not engage

pull the plastic cover off the top of the engine and check where the cable from the cruise control connects by the throttle body. There is a plastic connector that might be broken. i had the same problem and a piece of tape fixed it for me but you can replace the part if your picky.

Posted on Sep 30, 2009

Anonymous

SOURCE: 5.2 V8 Cruise control won't hold speed

Bad sending unit -on gas gauge. Remove Fuel Tank to replace.

Posted on Apr 29, 2010

Anonymous

  • 110 Answers

SOURCE: I recently replaced my brake booster. After the

hello there:
you may have over looked the vacuum line for the cruise control that hooks up to or close to brake booster hope this helps you out..sincerely D.Jones

Posted on Jun 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I troubleshoot the cruise control of a 2003 Alero?


It's probably a problem with cruise control module , located under the hood in engine compartment . Or a bad connection somewhere . Do you know how to do electrical testing ? Is the air bag light lit on the instrument cluster ?

Could have DTC'S - diagnostic trouble code's stored .
DTC P1554
The powertrain control module (PCM) inhibits cruise control operation when certain conditions are not appropriate for cruise control operation. The PCM removes the ground from the cruise control inhibit signal circuit in order to disengage cruise control operation.
DTC P1585
Output driver modules (ODMs) are used by the powertrain control module (PCM) in order to turn on many of the current driven devices that are needed to control various engine and transaxle functions. DTC P1558 set indicates that an improper voltage level has been detected on the signal circuit which controls the cruise control inhibit circuit.
Action Taken When the DTC Sets
• The PCM will not illuminate the malfunction indicator lamp (MIL).
• The PCM will store the conditions present when the DTC set as Failure Records data only.

Cruise control is a speed control system that maintains a desired vehicle speed under normal driving conditions. However, steep grades may cause variations in the selected speeds. The electronic cruise control system has the capability to CRUISE, COAST, RESUME SPEED, ACCELERATE, and TAP-UP or TAP-DOWN.
The main parts of the cruise control system are:
• The cruise control module assembly
• The function control switches
• The cruise control release switch
• The clutch pedal position switch (CPP), if equipped
• The stop lamp switch assembly
• The vehicle speed sensor
The cruise control system uses the cruise control module assembly to maintain the desired vehicle cruise speed and operation. The cruise control module assembly has an electronic controller and an electric stepper motor to vary the throttle in each different cruise control mode. The electric controller monitors vehicle speed and operates the electric stepper motor. The stepper motor operates in response to the electronic controller, to maintain the desired cruise speed. The electric stepper motor moves a strap that is attached to the cruise control cable which moves the throttle linkage. The cruise control module assembly contains a low speed limit which will prevent system engagement below a minimum speed of 40 km/h (25 mph). The module assembly is not serviceable.

Dec 11, 2016 | 2003 Oldsmobile Alero

1 Answer

How do i set the cruise control on my 1994 mercedes c220 elegance automatic


Cruise Control
Any given speed above approximately 22 mph (35 km/h) can be maintained with the cruise control by operating the lever.
-see photo

  1. Accelerate and set: Lift lever briefly to set speed. Hold lever up to accelerate.
  2. Decelerate and set:
    Depress lever briefly to set speed. Hold lever down to decelerate.
    Normally the vehicle is accelerated to the desired speed with the accelerator. Speed is set by briefly pushing
    the lever to position 1 or 2. The accelerator can be released. The speed can be increased (e.g. for passing)
    by using the accelerator. As soon as the accelerator is released, the previously set speed will be resumed automatically. If a set speed is to be increased or decreased slightly, e.g. to adapt to the traffic flow, hold lever in position 1 or 2 until the desired speed is reached, or briefly tip the control lever in the appropriate direction for increases or decreases in 0.6 mph (1 km/h) increments. When the lever is released, the newly set speed remains.
  3. Canceling
To cancel the cruise control, briefly push lever to position 3.
When you step on the brake or the vehicle speed drops below approx. 22 rnph (35 km/h), for example when driving upgrade, the cruise control will be canceled.
4. Resume
If the lever is briefly pushed to position 4 when driving at a speed exceeding approx. 22 mph (35 km/h), the vehicle resumes the speed which was set prior to the cancellation of the cruise control. The last memorized speed is canceled when the key in the steering lock is turned to position 1 or 0.
Note:
If the engine does not brake the vehicle sufficiently while driving on a downgrade, the speed you set on the cruise control may be exceeded and you may have to step on the brake pedal to slow down.
As soon as the grade eases, the cruise controlled speed will again be maintained as long as the brakes were not previously applied, or the lever may be used to resume the previously set speed if the brakes were applied.

set-cruise-control-1994-mercedes-c220-sufrpujyrsap3pvz3w2boz5j-3-0.jpg
http://www.benzworld.org/forums/attachments/w202-c36-c43/153145d1197313761-pdf-owners-manual-w202-1995-2000-1999-c280_owners_manual.pdf

Feb 14, 2015 | Mercedes-Benz C-Class Cars & Trucks

1 Answer

Ford focus cruise control


Once you have turned your cruise control on accelerate to desired speed press SET button on right hand side of steering wheel before lifting foot from accelerator, then remove foot from accelerator. pushing RESUME button will deactivate cruise control without turning it off. Then when clear of traffic push resume again to activate cruise control. It will automatically resume to previous set speed.

Apr 30, 2013 | 2006 Ford Focus

1 Answer

How do you set the cruise control on a 92 ford thunderbird sc


If you mean using it, you bring the car up to the desired speed, turn on the cruise with the on-off button on the horn pad, then hit "set" for the desired speed.

Aug 07, 2012 | Ford Thunderbird Cars & Trucks

1 Answer

How can i activate my cruise control in my 2004 grand cherokee


The cruise control switches are located on the steering wheel. When the cruise control is turned on there will be a green light luminated on the dash that says "cruise". When at the desired speed press "set" to set the cruise control at that speed.

Oct 09, 2010 | Jeep Cherokee Cars & Trucks

1 Answer

How to use cruise control


Here are the steps in using cruise control:

  1. Get on a road you will be traveling at the same speed for a long period of time, such as a freeway.
  2. Reach your desired speed. Choose a speed that allows you to move with the flow of traffic and not go over or under the designated speed limit for that road.
  3. Locate the ON and SET buttons on your steering wheel. Press ON first and SET after. Your cruise control is now activated. Most vehicles must be traveling at least 30 miles per hour to set the cruise control.
  4. Press and hold the SET button if you wish to use cruise control at a higher speed. Hold until your desired speed is reached.
  5. Decrease speed by pressing the COAST button.
  6. Push the brake pedal to disengage the cruise control function. If you wish to return to the previous set speed, use the RES (resume) button. You must be traveling at least 30 miles per hour for this function to resume.
  7. Erase any previous speed by pressing the OFF button.

Feb 11, 2010 | 2000 Nissan Maxima

2 Answers

How do i use cruise control on focus


Hello,
First the vehicle has to be operating at least 35mph. There will be two sets of switches, one set is to the left and the other set is to the right of the horn on the steering wheel. The switches on the left will be labeled on/off, the ones on the right we be labeled Coast/Accel/Resume..

At a steady highway speed press the ON switch, (at the left hand side of the horn) This will activate and turn the speed control system ON...

Then you have to set and adjust your desired speed...

To SET YOUR DESIRED speed , press and hold the accel switch (Right side of Horn) until your desired speed has been reached and then release the switch.. Speed control will now be on, activated and set, you will be in cruise mode..

If you need to coast due to possible traffic, press and hold the coast switch as long as you need to.. This is like taking your foot off of the accelerator pedal.. When you let go of the coast switch you will return to you set cruising speed.

Stepping on the brake pedal at any time will deactivate the system.. If you step on the brake, and then want to return to your previous set cruising speed... All you have to do is press resume...

I hope this has helped you? You can find detailed speed control activation instructions in your 2005 Ford Focus Owners manual.. If you did not receive your owners manual when you bought the vehicle.. You can purchase one at your local Ford, Lincoln or Mercury dealership..

Bill Andrade Ford Master Technician/Shop Foreman

Sep 22, 2009 | 2005 Ford Focus

2 Answers

What are the functions of Resume &Coast buttons in steering wheel


If set at a specific speed and you have to slow down by hitting the brakes, The brakes turn off the cruise control. Pressing resume automatically turns the cruise control back on and accelerates to the previous speed setting. You can also use it to accelerate and by releasing it the new speed will be set.

Jun 18, 2009 | 1996 Mercury Grand Marquis

1 Answer

Why cruise control won't work on 2003 ford explorer


If you hit "On", cruise control is on. It's just not set to the speed.

To properly set the cruise control, do the following procedure:

  1. Select the "On" button on the left side of the steering wheel
  2. On the right side of the steering wheel, there is a "+" along with "Set", press that button after you have accelerated to the speed you desire to maintain.
  3. Use the "+ and -" to speed up or slow down your vehicle.
  4. To temporarly disable the cruise control, simply press the brake pedal.
  5. To resume the previously desired speed, press the top button "Resume"

Jan 20, 2009 | 2003 Ford Explorer Sport

1 Answer

How to set cruise control


cruise control on your escape will work at 30 mph and up. Press 'on 'button, then press gas pedal 'til u reach desired speed, press 'set acc' and you'll be cruisen. You can also do it this way, press 'on' button, then press and hold 'set/acc' button, car will accelerate, let go of button when u reach desired speed. Putting on brakes will deactivate cruise, u can then press 'RSM' to resume speed.

Oct 21, 2008 | 2002 Ford Escape

Not finding what you are looking for?
2001 Honda Accord Logo

Related Topics:

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...