Question about 1999 Chevrolet Silverado 1500

1 Answer

How do you get the front bulb assembly out past the lower bumper to replace bulbs ? 2009 Tahoe

Posted by dbutz307 on

Ad

1 Answer

ruben sanchez

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 228 Answers

Each headlight has a rod L shaped on the right and left end of the light. they look like latches. unlatch

the rods and pull them straight up. once the rods are removed you can pull out the headlight assembly,

and you can have access to your running lights. on the battery side you may have to remove the battery

putting the lights back on is the reverse process, you just have to alighn the holes and make sure the

wire does not get in the way. good luck!

Posted on Feb 16, 2011

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW TO REMOVE A HEADLIGHT FROM A 2007 SATURN OUTLOOK XE


Hi Carol , your going to have to remove the headlamp assembly to replace the bulb !


Remove the headlamp assembly. Refer to Headlamp Replacement.



1



Headlamp Bulb Accessory Covers (Qty: 2)



2



Headlamp Bulb Assembly (High Beam)




Caution: Refer to Halogen Bulb Caution in the Preface section.




Tip

Disconnect the electrical connectors and remove the bulbs.



3



Headlamp Bulb Assembly (Low Beam)


Callout

Component Name

Preliminary Procedure

Remove the front bumper fascia. Refer to Front Bumper Fascia Replacement .




Headlamp Assembly Bolt (Qty: 4)

Notice: Refer to Fastener Notice in the Preface section.

Tighten

6 N?·m (53 lb in)







2





Headlamp Fascia Brace Fender Reinforcement Bolt




Tighten

6 N?·m (53 lb in)







3





Headlamp Cam Adjuster




Procedure

Set the headlamp adjusters at the nominal setting of 6 turns off fully seated.







4





Headlamp Cam Locking Nut







5





Headlamp Assembly




Tip

Disconnect the electrical harness as the headlamp assembly is being removed from the vehicle.

Apr 08, 2015 | 2007 Saturn Outlook XE

1 Answer

How do you replace the right head light bulb on a 2009 malib?


Need to take the front bumper off in order to get to the screws of the assembly

Aug 25, 2014 | 2009 Chevrolet Malibu

1 Answer

Changing a parking light bulb in front head light assembly


Remove the front wheel liner from the strut to the front bumper, all light assembly light bulbs will then be accessible. There may be screws however the majority is a plastic clip where you pull the center out then the clip easily removes.

Sep 08, 2013 | 2009 Buick Enclave

1 Answer

How do you remove the front headlight assembly on a 2009 Nissan Quest?


are you trying to replace bulb if so open hood and behind the assembly is the bulb tight fit but un screw a ring and pull old bulb out and put replacement bulb in. if replacing whole assembly there is a couple clips on it may need to remove bumper cover to see bottom clip

Apr 06, 2013 | Cars & Trucks

1 Answer

Need to replace the headlight assembly on front passenger side do i have to take off the bumper? for ponitac vibe 2003 also have dent on the area


Yes you do. This is the steps to do that to replace the entire headlight assembly:


Remove the front fascia.
  • Remove the front fascia extensions, if equipped.
  • Remove the front fender liners.
  • Remove the fog lamps.
  • Remove the bolts (4) from the front bumper fascia (3) at the fender.


506bafd.gif

Remove the bolts from the front bumper fascia at the fender



  • Remove the push-in retainers (2) from the bumper fascia using J38778.
  • Remove the fascia bolts (1) from the fascia.
  • Remove the fascia from the vehicle.
  • Remove the 3 bolts which secure the composite headlamp.


  • 7f1ec16.gif

    Remove the 3 bolts which secure the composite headlamp



    1. Remove the sidemarker bulb electrical connector.
    2. Remove the sidemarker bulb, if necessary.
    3. Remove the composite headlamp assembly from vehicle.

    To install:

    1. Install the sidemarker bulb to the composite headlamp, if removed.
    2. Connect the sidemarker bulb electrical connector.
    3. Secure the composite headlamp to the vehicle with the 3 bolts. Tighten the headlamp mounting bolts to 89 inch lbs. (10 Nm).
    4. Install the front fascia.
    5. Install the headlamp bulb to the composite headlamp, if removed.
    6. Fasten the headlamp bulb retainer clip.
    7. Install the socket to the headlamp bulb.
    8. Install the rubber cover to the composite headlamp.
    9. Aim the headlamps.
    10. Close the hood.

    Oct 12, 2010 | 2003 Pontiac Vibe

    1 Answer

    How do I replace a front turn signal bulb in my 2009 Impala?


    Remove the headlamp assembly and replace the bulb.If you have under 36k miles this is still under the bumper to bumper warranty and the dealership will fix it for free.Hope this helps.Good luck.

    Mar 24, 2010 | 2009 Chevrolet Impala

    1 Answer

    How do I change my front turn signal? I can access the lower signal from under the bumper, I can't access the signal that is next to the headlight. There are no screws in front to take the plate off,...


    The signal light on the grill next to the head light can be accessed by removing the the front grill. Your going to need a torque screw driver to remove the grill to get to the light bulb. The signal from under the bumper can be accessed from behind the bumper and you need not to take the turn light assemble off from the bumper. There are LED light bulbs available now and last much longer then the conventional bulbs and cost not that much more. Auto Zone carries these replacement LED bulbs and they can give you the step by step instruction to getting the job done if you need more illustration. Good luck and hope this helps and please rate, keep me posted. Be glad to help you get your lights replaced.

    Jan 10, 2010 | 1991 GMC Sonoma

    1 Answer

    How do you replace the fog light bulbs on a 2004 buick regal?


    Notes FOG LAMP BULB REPLACEMENT - FRONT

    REMOVAL PROCEDURE
    f98bf40.gif
    1. Remove the front bumper fascia deflector.
    2. Disconnect the electrical connector from the front fog lamp bulb/socket. CAUTION: Refer to Halogen Bulb Caution in Service Precautions.
    01c84b0.gif
    1. Rotate the front fog lamp bulb/socket counterclockwise to release.
    2. Remove the fog lamp bulb/socket from the front fog lamp assembly.
    4065803.gif


    1. Install the fog lamp bulb/socket to the fog lamp rotating clockwise until fully seated. CAUTION: Refer to Halogen Bulb Caution in Service Precautions.
    b182709.gif
    1. Connect the electrical connector to the front fog lamp bulb/socket.
    2. Install the front bumper fascia deflector.

    Jun 16, 2009 | Buick Regal Cars & Trucks

    1 Answer

    Access headlight bulbs for 2007 tahoe


    When you open the hood, you will see little plastic tabs that you can pull up. This will release the headlight assembly, and give you access to the bulbs.

    Mar 24, 2009 | 2007 Chevrolet Tahoe

    1 Answer

    How to replace front turn light bulb on Caddy SRX 2004?


    1. Open the hood.
    2. Remove the push-pin retainers that secure the top of the upper fascia and grille assembly to the upper tie bar to allow the upper fascia and grille assembly to flex forward.
    3. Remove the bolt and the push-pin retainer that secures the top of the headlamp assembly to the upper tie bar.
      1. Gently pull the upper fascia and grille assembly forward only far enough to remove the bolt located at the bottom inboard side of the headlamp assembly.
      2. Pull the headlamp assembly straight out to disengage the snap-in retainer at the lower outboard back surface of the assembly. Turn the assembly so that the front inboard corner clears the front fascia.
      3. Pull the headlamp assembly out and away from the vehicle
      4. Disconnect the headlamp electrical connector.
      5. Remove the headlamp assembly from the vehicle.
      6. Remove the headlamp bulb cover from the headlamp assembly.
      7. Remove the headlamp bulb socket from the headlamp assembly.
      8. Remove the headlamp bulb.
      9. Remove the side marker bulb socket from the outer side of the headlamp assembly.
      10. Remove the side marker bulb.

    Feb 12, 2009 | 2006 Cadillac SRX

    Not finding what you are looking for?
    1999 Chevrolet Silverado 1500 Logo

    183 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    Marvin
    Marvin

    Level 3 Expert

    85239 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22485 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8984 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...