Question about Ford Explorer Sport Trac

Open Question

I need a 2005 ford explorer repair manual to replace my signal/wiper control arm

Posted by dcdill06 on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to access linkage rod on wipers ford explorer


remove the wiper arms first of all by pulling back the locking tab at the mounting area of the arm. Pull straight off then remove the plastic cowl vent to gain access to the wiper linkage

Aug 24, 2012 | 2005 Ford Excursion

1 Answer

95 windstar, replaced the wiper transmission and now the windshield wipers wont park in the proper position.brought it to a mechanic and he said it was the wiper control switch.replaced that, he was...


simple actually- 1- on wiper arms- flip up cap on end- remove nut, 2 using a screw driver and small wood block lift arms off driver screw.3 turn key on cycle wipers- turn off 4- reattach arms in correct position and retighten-., test with arms up- not on glass- is still wrong- the link from wiper motor to cross arm wrong- - buy a HAYES repair manual- will show how to remove cowl cover yourself- is easy , then follow instuctions in manual to correct link

May 10, 2011 | Ford Windstar Cars & Trucks

1 Answer

2002 Ford Explorer Wiper activate when making L/R signal


The switch could have a short in it, most llikely you will need to replace the switch.

May 28, 2010 | 2002 Ford Explorer Sport

1 Answer

Replace rear wiper arm


there is a cover at the base lift it up and then you have a nut. 10mm remove this and pull off the arm. sometime they get stuck and you will have to pry it up.

Apr 01, 2010 | 1999 Ford Explorer

1 Answer

How do i replace the bushings on my windshield wipers on a ford explorer? Drivers side wipers bushing is wore and needs replacing. having a hard time putting the arm and new bushing back on the ball of the...


the parts in order for this wiper system has 4 items involved.
the wiper motor, the wiper transmission, the wiper arms, and the wiper blades
if the bushing is too hard to install its destroyed and it will jamb up on you
replace the transmission unit is the best option to do

Mar 06, 2010 | 2001 Ford Explorer Sport

1 Answer

Rear wiper in 2005 barely touches window. Need to


I have a 2002. I thought this problem got fixed before 2005. I couldn't get my arm off because of internal corrosion. I took the wiper blade off to get a little more swing with the arm. I oiled and swung the arm to get it loosened up. Then I bent the arm towards the glass to get more spring pressure and reattached the blade. That will work for a little while. You can get a new arm from Autozone #42536 for $28 plus shipping.

Jan 24, 2010 | Ford Escape Cars & Trucks

1 Answer

The wiper motor on my 1983 Ford Ranger still works but the wipers no longer move. I think there is a failure of the mechanical linkage. Where do I go to find repair parts?


why do you think the motor still works if the wipers don't move? Can you hear the motor run or can you see a little movement when you turn the switch on?

What happens when you activate the washers?

go to a salvage yard that allows you to remove the parts yourself. Then you can see how the motor and linkage assembly comes out.


don't have 1983 info, but here is 1994:

Section 01-16A: Wiper and Washer System, Ranger/Explorer 1994 Ranger and Explorer Vehicles Workshop Manual
DESCRIPTION AND OPERATION Windshield Wiper System, Ranger/Explorer The windshield wipers are actuated by a permanent magnet, rotary-type electric windshield wiper motor (17504) . The two windshield wiper pivot arms (17526) and windshield wiper blades (17528) are mounted on a pivot shaft, one at each side of the windshield. The windshield wiper mounting arm and pivot shaft (17566) are connected to the motor by windshield wiper adapter and connecting arm clip (17531) . Ranger and Explorer vehicles are equipped with an interval wiper and washer (IWW) system featuring a lever-type turn signal and windshield wiper switch (13K359) mounted on the steering column. The IWW windshield wiper governor (17C476) uses a relay contact to control current to the windshield wiper motor . The governor electronic circuitry controls the contact to supply current to windshield wiper motor . A rear wiper/washer system is available on Explorer vehicles. The rear window wiper system consists of a windshield wiper motor mounted inside the liftgate (40010) , an articulating windshield wiper pivot arm and windshield wiper blade , a windshield wiper/washer switch (17A553) and an inline circuit breaker. The front electric windshield washer system consists of a control switch, integral with the turn signal, a windshield washer reservoir (17618) and windshield wiper motor and the necessary windshield washer hoses (17A605) , windshield washer nozzle jet and brackets (17603) and attaching parts.
------------------------------------------------------------------------------------------------
Pivot Shafts and Linkage Removal and Installation
NOTE: The left and right pivot and windshield wiper adapter and connecting arm clip assemblies are serviced separately.
  1. Perform Steps 1 through 9 of Windshield Wiper Motor Removal as described in this section.
  1. If servicing left windshield wiper adapter and connecting arm clip , remove left windshield wiper mounting arm and pivot shaft and windshield wiper blade assembly.
  1. Remove left windshield wiper adapter and connecting arm clip access cover.
  1. Remove left pivot nut, lower windshield wiper adapter and connecting arm clip and slide it out through left access opening. For installation, follow removal procedures in reverse order. Tighten nut to 10-13 Nm (7-10 ft-lb). Make sure the clip is fully seated in the windshield wiper adapter and connecting arm clip . Do not try to install clip with windshield wiper adapter and connecting arm clip on motor crank pin.
----------------------------------------------------------
Windshield Wiper Motor Windshield wiper motor are not serviceable. If worn or damaged, the windshield wiper motor must be replaced as an assembly. Removal
  1. Cycle windshield wiper blades until in straight-up position and turn ignition switch OFF.
  1. Disconnect battery and wiper motor electrical connector.
  1. Remove the right windshield wiper mounting arm and pivot shaft and windshield wiper blade .
  1. Disconnect the battery ground cable (14301).
  1. Remove the right pivot nut and allow the windshield wiper adapter and connecting arm clip to drop into the cowl top outer panel .
  1. Remove the linkage access cover, located on the right side of the dash panel near the windshield wiper motor.
  1. Reach through the access cover opening and unsnap the wiper motor clip.
  1. Push the clip away from the windshield wiper adapter and connecting arm clip until it clears the nib on the crack pin. Then, push the clip off the windshield wiper adapter and connecting arm clip.
  1. Remove the windshield wiper adapter and connecting arm clip from windshield wiper motor crank pin.
  1. Remove nut and ground strap.
  1. Remove three attaching nuts from windshield wiper motor. Remove the windshield wiper motor .
Installation
  1. Position the windshield wiper motor and install the three attaching screws. Tighten to 13.6-19.0 Nm (10-14 ft-lb).
  1. Install nut and ground strap.
  1. Connect wiper motor electrical connector.
  1. Install clip completely onto right windshield wiper adapter and connecting arm clip. Make sure the clip is fully seated. Do not put the windshield wiper adapter and connecting arm clip on the motor crank pin and then try to install the clip.
  1. Install the left windshield wiper adapter and connecting arm clip onto the wiper motor crank pin.
  1. Install the right windshield wiper adapter and connecting arm clip onto the wiper motor crank pin. Pull the windshield wiper adapter and connecting arm clip onto the crank pin until it snaps into place. The clip is properly installed if the nib is protruding through the center of the clip.
  1. Install the right windshield wiper mounting arm and pivot shaft and nut. Tighten the nut to 9.5-12.5 Nm (84-110 in-lb). NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven 10 miles or more to relearn the strategy.
  1. Connect the battery ground cable and turn the ignition switch on. Turn turn signal and windshield wiper switch off so windshield wiper motor will park, then turn ignition switch off. Replace right windshield wiper adapter and connecting arm clip access cover.
  1. Install the windshield wiper mounting arm and pivot shaft and windshield wiper blade assemblies on the pivot shafts to dimension X. Dimension X is the distance between the centerline of the blade saddle and the top edge of the cowl top outer panel grille. The value of Dimension X for each vehicle is given in the Dimension X chart in the Specifications portion of this section.
  1. Test the system.
6bd608c.gif

Jan 04, 2010 | 1983 Ford Ranger

1 Answer

HOW DO I REPLACE A REAR WINDOW WIPER ON 2005 FORD ESCAPE?


Remove the rear pivot arm.
Lift the pivot arm to the upright position.
Slide the locking tab out.
Pull up and remove the pivot arm.
Remove the rear wiper motor shaft nut cover.
Remove the rear wiper motor shaft nut.
Remove the rear wiper motor cover.
Remove the rear wiper motor bracket nut.
Remove the bolt and the rear wiper motor.

Jan 29, 2009 | 2005 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...